• 한국산학기술학회논문지
• /
• 제14권1호
• /
• pp.57-62
• /
• 2013

카트 차체에는 현가장치와 차동장치가 존재하지 않으므로 카트주행 중 발생하는 프레임의 변형은 탄성변형으로 인한 주행성능과 프레임의 피로수명에 영향을 미친다. 선회주행 시 비틀림 변형에 의한 카트의 거동은 이 두 가지 변형에 결정적 원인을 제공한다. 이러한 곡선구간에서 카트의 동적 거동을 분석하기 위하여 GPS를 이용하여 차량의 궤적을 추적하고 카트 프레임 강에 작용하는 비틀림 응력을 측정하였다. 레저와 레이싱 카트 프레임의 기계적 성질을 파악하기 위해 재질 분석과 인장시험을 실시하여 각 프레임의 재료 특성을 분석하였다. 비틀림 응력집중과 프레임 비틀림은 프레임 해석을 통해 조사되었다. 또한 주행 분석 장치를 이용하여 레저와 레이싱 카트를 각 조건별로 실차실험을 수행하였고, 이를 통해 곡선구간에서 카트의 주행거동을 분석하였다. 선회주행 시 차량에 원심력에 의한 하중이동의 현상이 발생했으며, 이로 인해 카트 프레임 강에 비틀림 응력이 발생하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.282-286
• /
• 2000

In this paper, magneto-rheological(MR) damper is studied for vibration control of large infra structures under earthquake. Generally, active control devices need a large control force and a high power supply system to reduce the vibration effectively. Large and miss tuned control force may induce the dangerous situation such that the generated large control force acts to amplify the structural vibration. Recently, to overcome the weaknesses of the active control, the semi-active control method is suggested by many researchers. Semi-active control uses the passive control device of which the characteristics can be modified. Control force of the semi-active device is not generated from the actuator with power supply. It is generated as a dynamic reaction force of the device same as in the passive control case, so the control system is inherently stable and robust. Unlike the case of passive control, control force of semi-active control is adjusted depending on the measured response of the structure, so the vibration can be reduced more effectively against various unknown environmental loads. Magneto-rheological(MR) damper is one of the semi-active devices. Dynamic characteristics of the MR material can be changed by applying the magnetic fields. So the control of MR damper needs only small power. Response time of MR to the input voltage is very short, so the high performance control is possible. MR damper has a high force capacity so it is adequate to the vibration control of large infra structure. Because MR damper has a nonlinear property, normal control method used in active control may not be effective. Clipped optimal control, modified bang-bang control etc. have been suggested to MR damper by many researchers. In this study, sliding mode fuzzy control(SMFC) is applied to MR damper. Genetic algorithm is used for the controller tuning. To verify the applicability of MR damper and suggested algorithm, numerical simulation on the aseismic control is carried out. Simulation model is three-story building structure, which was used in the paper of Dyke, et al. The control performance is compared with clipped optimal control. The present results indicate that the SMFC algorithm can reduce the earthquake-induced vibration very effectively.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.65-72
• /
• 2019

In long freight trains, there is a brake time delay in neighboring freight cars, which causes damage and fractures in the couplers, especially at their knuckle. A problem in the couplers of the cars can cause derailment and damages of human life and property. In this study, maximum forces on the couplers are studied when a long freight car brakes with the brake delay time and coupler gap. We make a dynamic model of 50 freight cars and couplers, applying contact between the couplers and a characteristic curve to express the force and displacement of the buffers using SIMPACK, which is a multi-body dynamics program. We use EN 14531-2, which is a standard of freight car brakes, to verify the dynamic model. Then, we compare the analyzed impact force with the coupler knuckle standard after applying the two carriages of a locomotive in the model based on the dispersed double head control system. The result shows that all coupler gap conditions satisfy the infinite lifetime of the material when the brake delay time is 0.1 second.

• 한국의상디자인학회지
• /
• 제15권2호
• /
• pp.77-89
• /
• 2013

This study investigated the formation of silhouette and hemline shape of knit flare skirts according to the properties of knit material through virtual clothing with a 3D virtual clothing system called i-Designer of Technoa, thus building a database of the property data of knit material to reduce the number of sample making steps repeated and implemented several times in the process of clothes making. The results would help to estimate a silhouette in advance, offer assistance to the development of original knit wear, and explore ways to provide basic data for the development of the knit industry of the nation. The investigator made 12 kinds of experimental clothes to the angles(width of skirt: $90^{\circ}$ and $180^{\circ}$), gauge(7G, 12G, and 15G), and grain directions(wale and bias direction) of experimental clothes for virtual clothing. The dynamic characteristics of knit skirt samples according to each gauge were measured with the KES-FB system. Draper shapes were analyzed with the sectional shape data of hemline based on i-Designer. As for the measurements of the sectional shape of hemline and the formation of silhouette, the number of nodes, the average height of node mountains and valleys, and the hemline width right and left and before and after increased at the angle of $180^{\circ}$ than $90^{\circ}$. As gauges multiplied, the number of nodes, and silhouette angle dropping. When considering grain directions, the number of nodes and silhouette index increased in the wale direction at the angle of $90^{\circ}$ with the number of nodes and silhouette angle increasing in the wale direction at the angle of $180^{\circ}$.

• 공업화학
• /
• 제24권1호
• /
• pp.104-111
• /
• 2013

본 연구에서는 생분해성 지방족 폴리에스터 중 비교적 고가인 poly(butylene adipate-co-terephthalate) (PBAT)와 상대적으로 저가의 생분해성 고분자인 polylactic acid (PLA)의 블렌드에 3종류의 개질제를 사용하여 그 효과를 조사하였다. 개질제로는 에폭시계의 커플링제와 diisocyanate계열의 methylenediphenyl 4,4'-diisocyanate (MDI)와 hexamethylene diisocyanate (HDI)를 사용하였다. 여러 가지 조성의 블렌드에 용융흐름지수, 동적 점탄성을 조사하였다. 또한, 인장시험을 통한 기계적 물성 조사와 FE-SEM으로 시편의 파단표면을 관찰하였다. 이를 통해 PLA/PBAT 블렌드의 상용성과 개질제의 효과 및 기계적물성에 미치는 영향을 고찰하였다. 개질제로 HDI를 사용했을 때 PLA/PBAT의 인장물성이 크게 증가하였다.

• 대한조선학회논문집
• /
• 제53권2호
• /
• pp.85-91
• /
• 2016

The most important factor in the structural design of ships and offshore structures operating in arctic region is ice load, which results from ice-structure interaction during the ice collision process. The mechanical properties of ice related to strength and failure, however, show very complicated aspect varying with temperature, volume fraction of brine, grain size, strain rate and etc. So it is nearly impossible to establish a perfect material model of ice satisfying all the mechanical characteristics completely. Therefore, in general, ice collision analysis was carried out by relatively simple material models considering only specific aspects of mechanical characteristics of ice and it would be the most significant cause of inevitable errors in the analysis. Especially, it is well-known that the most distinctive mechanical property of ice is high dependency on strain rate. Ice shows brittle attribute in higher strain rate while it becomes ductile in lower strain rate range. In this study, the simulation method of ice collision to ship hull using the nonlinear dynamic FE analysis was dealt with. To consider the strain rate effects of ice during ice-structural interaction, strain rate dependent constitutive model in which yield stress and hardening behaviors vary with strain rate was adopted. To reduce the huge amount of computing time, the modeling range of ice and ship structure were restricted to the confined region of interest. Under the various scenario of ice-ship hull collision, the structural behavior of hull panels and failure modes of ice were examined by nonlinear FE analysis technique.

• 대한토목학회논문집
• /
• 제37권2호
• /
• pp.289-301
• /
• 2017

국내외적으로 지진의 발생이 빈번함에 따라 인명 및 재산 피해가 발생하고 추가적인 경제적 손실을 초래한다. 국내의 비내진으로 설계된 구조물의 보수 보강이 시급할 뿐만 아니라 지진에 대한 관심이 고조됨에 따라 내진보강에 대한 연구가 활발히 진행되고 있다. 최근 고연성 보강재를 사용한 내진보강기법이 소개되면서 강성보강보다는 연성보강에 대한 신뢰도가 높아지고 있다. 따라서 본 연구에서는 연성보강 재료로써 최근 각광받고 있는 폴리우레아를 이용한 내진보강공법을 소개하기 위해서, 폴리우레아로 보강한 RC 시편에 대하여 일축압축시험과 유사동적실험을 수행하였다. 일축압축시험에서 폴리우레아 보강시 강도가 증진되었을 뿐 아니라 연성거동을 확인할 수 있었으며, 실제 지진파를 적용한 유사동적실험에서는 상대변위, 주철근의 변형률, 변위연성도, 소산에너지 모두 향상된 보강성능을 확인할 수 있었다. 연성보강의 목적으로 개발한 폴리우레아 보강방법은 기둥부재의 내진보강에 유용하게 사용될 것이라고 판단된다.

• 한국도로학회논문집
• /
• 제10권1호
• /
• pp.87-95
• /
• 2008

형상이 일정하지 않은 구조에 충돌하는 차량의 탑승자 안전을 확보하기 위해서 그 구조물의 앞에 공간이 허용하는 한도의 깊이만큼 충격을 흡수하는 재료로 만든 모듈을 쌓아두는 방법을 생각할 수 있다. 충격흡수모듈로 사용되기 위해서는 재료가 충분한 에너지 흡수능력을 가져야 하고 동시에 탑승자의 안전을 확보할 수 있어야 한다. 본 논문에서는 에너지 흡수능력과 더불어 탑승자의 안전을 보장하기 위하여 충격흡수재료가 가져야 할 조건을 설명하고 auard-Guard 시스템 모듈, 샌드백, 재활용 타이어, 지오컨테이너, 지오셀 그리고 EPS 블록에 대한 정적압축실험을 실시하여 그 결과를 분석하였다. 이로부터 $30kg/m^{3}$의 밀도를 갖는 EPS 블록이 쿠션모듈로 사용되기 적합한 재료임을 보였다. 한편 시속 35.6km/h까지의 충돌조건으로 Drop Test를 실시하여 EPS블록의 정적특성과 동적특성간 큰 차이가 없음을 보여 주었으며 쿠션모듈로서의 성질을 개선시키기 위한 방안으로 EPS 블록에 공극을 두는 방안을 제안하고 공극이 있는 EPS블록에 대하여 Drop Test를 실시하여 EPS 블록을 이용한 충격흡수시설의 설계에 필요한 재료적 특성치를 제시하였다.

• 한국염색가공학회지
• /
• 제27권1호
• /
• pp.18-26
• /
• 2015

para-aramid fibers were treated by atmosphere air plasma to improve the interfacial adhesion. The wettability of plasma-treated aramid fiber was observed by means of dynamic contact angle surface free energy measurement. Surface roughness were investigated with the help of scanning electron microscopy and atomic force microscopy. The tensile test of aramid fiber roving was carried out to determine the effect of plasma surface treatments on the mechanical properties of the fibers. A pull-out force test was carried out to observe the interfacial adhesion effect with matrix material. It was found that surface modification and a chemical component ratio of the aramid fibers improved wettability and adhesion characterization. After oxygen plasma, it was indicated that modified the surface roughness of aramid fiber increased mechanical interlocking between the fiber surface and vinylester resin. Consequently the oxygen plasma treatment is able to improve fiber-matrix adhesion through excited functional group and etching effect on fiber surface.

• 복식문화연구
• /
• 제23권5호
• /
• pp.737-754
• /
• 2015

The structural aesthetics of architecture are becoming an inspirational source for many fashion designers and have been reborn in structural fashion. This study planned to analyze the method of expression of structural aesthetics expressed in modern structural fashion design and the construction method to maximize such an effect on the basis of the construction characteristic of Santiago Calatrava as the representative architect of the structural aesthetic. According to the study, the structural aesthetics expressed in modern structural fashion design are as follows: 1) The symbolical formative aesthetic expressed by symbolical inference and analyzation; 2) the dynamic beauty of physic expressed by visual emphasis and dynamics; and 3) the asymmetric beauty of symmetry expressed by metastasis toward the boundary between balance and imbalance. In addition, to maximize structural aesthetics, we used repetition and a progressive technique based on rhythm, asymmetry, and incision-based variances, such as balance, polygon flux, and inference, and analyzation-based distortion as the structuring principle. The following expression methods for maximizing structural aesthetics were found: 1) symbolical and structural exaggeration of appearance; 2) detail technique expansion and material property diversification; and 3) the three-dimensional transformation of structure and shell expression. Structural fashion design was found to have maximized structural aesthetics by using such expression methods to secure artistic esthetics, destroy existing shapes and patterns, and create unique shapes.