• Fire Science and Engineering
• /
• v.27 no.3
• /
• pp.1-7
• /
• 2013

The wildland fire intensity and scale are getting bigger owing to climate change in the world. In the case of domestic, the forest is distributed over approximately 63.7 % of country and the main facilities like a industrial facility or gas facility abuts onto it. Therefore there is potential that the wildland fire is developed to a large-scale disaster. In this study, the effect distances of the radiant heat flux from the crown fire are analysed according to the change of wind velocity. The safety criteria concerning the radiant heat flux to influence on the surrounding were researched to analyse the effect distances. The criteria of radiant heat flux were chosen $5kW/m^2$, $12.5kW/m^2$, $37.5kW/m^2$. WFDS, which is an extension of NIST's Fire Dynamics Simulator, was used to consequence analysis of the forest fire. In order to apply the analysis conditions, it is researched the forest conditions that is generally distributed in domestic region. As the result, the maximum effect distances by radiant heat were showed at the horizontal and vertical direction. When the wind velocity varied from 0 to 10 m/s, the maximum effect distance increased as the wind velocity increases. Interesting point is that the maximum effect distance were shown at the wind velocity of 8 m/s. The maximum effect distance was decreased according as the fuel moisture of trees increase. This study can contribute to analyse quantitative risk about the damage effect of the surrounding facilities caused by wildland fire.

• Applied Chemistry for Engineering
• /
• v.23 no.5
• /
• pp.433-439
• /
• 2012

In this study, a cationic surfactant BHMAS (N,N-bis-(3'-n-dodecyloxy-2'-hydroxypropyl)-N-methyl-2-hydroxyethylammonium methyl sulfate) having two lauryl and three hydroxyl groups was synthesized by the reaction of n-dodecyl glycidyl ether and 2-aminoethanol followed by the quarternization with dimethyl sulfate. The structure of the product was elucidated by $^{1}H-NMR$ and FT-IR. The CMC (critical micelle concentration) and surface tension of BHMAS at CMC condition were found to be $9.12\;{\times}\;10^{-4}$ mol/L and 28.71 mN/m respectively. Dynamic surface tension measurements using a maximum bubble pressure tensiometer indicated that a relatively long time was required to saturate the interface between air and aqueous surfactant solution. The interfacial tension measured between 1 wt% surfactant solution and n-decane reached an equilibrium value of 0.045 mN/m in 5 min. The adsorption capacity of the synthesized surfactant was observed to be excellent, which suggests that the surfactant can be used as a softening agent during a laundry process.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.1-7
• /
• 2010

In the present work, an electrowinning process in the LiCl-KCl/Cd system is considered to model and analyze the electrotransport of the actinide and rare-earth elements. A simple dynamic modeling of this process was performed by taking into account the material balances and diffusion-controlled electrochemical reactions in a diffusion boundary layer at an electrode interface between the molten salt electrolyte and liquid cadmium cathode. The proposed modeling approach was based on the half-cell reduction reactions of metal chloride occurring on the cathode. This model demonstrated a capability for the prediction of the concentration behaviors, a faradic current of each element and an electrochemical potential as function of the time up to the corresponding electrotransport satisfying a given applied current based on a galvanostatic electrolysis. The results of selected case studies including five elements (U, Pu, Am, La, Nd) system are shown, and a preliminary simulation is carried out to show how the model can be used to understand the electrochemical characteristics and provide better information for developing an advanced electrowinner.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.1
• /
• pp.92-100
• /
• 2008

The existing transportation systems is emerged as a major obstacle to solve the problems such as a traffic jam and the increasing cost for a distribution and a traffic safety. In hun, ITS targeting intellectual vehicles and transportation infrastructure like road and signals is getting more important and the standards of ITS wireless communication is also getting attention. New traffic control strategies are being developed to utilize real-time traffic information collected by detection method using ITS wireless technology. Especially, DSRC system is being expanded wit ETCS and the use of OBU is spreading. These infrastructures will have much influence on ITS industry and a profound study on the method of utilizing a present infrastructure is going on in various fields. The optimum traffic signal control system using quality real-time information through these infrastructure is under development and so is WISDOM. Accordingly, this paper proposes communication protocol utilizing DSRC to collect real-time traffic information in WISDOM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3C
• /
• pp.307-314
• /
• 2003

In the general multiple video object coder, more interested objects such as speaker or moving object is consistently coded with higher priority. Since the priority of each object may not be fixed in the whole sequence and be variable on frame basis, it must be adjusted in a frame. In this paper, we analyze the independent rate control algorithm and global algorithm that the QP value is controled by the static parameters, object importance or priority, target PSNR, weighted distortion. The priority among static parameters is analyzed and adjusted into dynamic parameters according to the visual interests or importance obtained by camera interface. Target PSNR and weighted distortion are proportionally derived by using magnitude, motion, and distortion. We apply those parameters for the weighted distortion control and the priority-based control resulting in the efficient bit-rate distribution. As results of this paper, we achieved that fewer bits are allocated for video objects which has less importance and more bits for those which has higher visual importance. The duration of stability in the visual quality is reduced to less than 15 frames of the coded sequence. In the aspect of PSNR, the proposed scheme shows higher quality of more than 2d13 against the conventional schemes. Thus the coding scheme interfaced to human- eye proves an efficient video coder dealing with the multiple number of video objects.

• Korean Chemical Engineering Research
• /
• v.46 no.4
• /
• pp.799-805
• /
• 2008

In general, anionic and cationic surfactants are incompatible because their mixtures form insoluble complexes and precipitate in the water. There are, however, some equimolar complexes of anionic and cationic surfactant that are soluble and behave like regular surfactants, specifically like nonionic surfactants, thus named pseudo-nonionic surfactant complexes. Pseudo-nonionic complexes are more effective and efficient in surface activities than their ionic surfactant components as shown by their equilibrium and dynamic surface tensions. They pack at the interface more than their ionic components. When a novel cationic surfactant, diglyceryl dodecyl dimethyl ammonium chloride(DGDAC), having the polyhydroxyl group at the hydrophilic head group, was mixed with a conventional anionic surfactant (sodium dodecyl sulfate; SDS) at equimolar ratio, we found that the aqueous equimolar mixture showed strong positive synergism in which molecular interaction parameter ${\beta}^M$ was very low, -17.2. According to the studies of equilibrium phase behavior and microscopy, this mixed system could form homogenous solutions containing vesicles.

• Publications of The Korean Astronomical Society
• /
• v.21 no.2
• /
• pp.67-74
• /
• 2006

We have developed a control electronics system for an infrared detector array of KASINICS (KASI Near Infrared Camera System), which is a new ground-based instrument of the Korea Astronomy and Space science Institute (KASI). Equipped with a $512{\times}512$ InSb array (ALADDIN III Quadrant, manufactured by Raytheon) sensitive from 1 to $5{\mu}m$, KASINICS will be used at J, H, Ks, and L-bands. The controller consists of DSP(Digital Signal Processor), Bias, Clock, and Video boards which are installed on a single VME-bus backplane. TMS320C6713DSP, FPGA(Field Programmable Gate Array), and 384-MB SDRAM(Synchronous Dynamic Random Access Memory) are included in the DSP board. DSP board manages entire electronics system, generates digital clock patterns and communicates with a PC using USB 2.0 interface. The clock patterns are downloaded from a PC and stored on the FPGA. UART is used for the communication with peripherals. Video board has 4 channel ADC which converts video signal into 16-bit digital numbers. Two video boards are installed on the controller for ALADDIN array. The Bias board provides 16 dc bias voltages and the Clock board has 15 clock channels. We have also coded a DSP firmware and a test version of control software in C-language. The controller is flexible enough to operate a wide range of IR array and CCD. Operational tests of the controller have been successfully finished using a test ROIC (Read-Out Integrated Circuit).

• Journal of Dental Rehabilitation and Applied Science
• /
• v.35 no.4
• /
• pp.235-243
• /
• 2019

Osseointegration has been reported to be a dynamic process in which the alveolar bone comes in direct contact with the implant. Various methods were tried to evaluate degree of osseointegration and the measurement of bone-implant contact (BIC) have been commonly used among them. To properly assess the BIC, only histologic analysis is available. However, few studies evaluated BIC of successfully osseointegrated implants in humans. Thus, this is a unique opportunity when implants should be explanted due to inappropriate positioning of implant, presence of pain or sensory disturbance, or broken screw or fixture. This report presents a case of the implant underwent 3-year functional load and a histologic analysis after the fixture fracture. The histomorphometric analysis revealed 53.1% of BIC measured along the whole implant and 70.9% measured only in subcrestal area, respectively. In the present study, although the implant was fractured, a high degree of BIC was observed.

• Journal of KIISE:Software and Applications
• /
• v.29 no.9
• /
• pp.605-618
• /
• 2002

The CBD (Component Based Development) is a requisite technique for the Time-To-Market, and a highly reusable component should be provided to develop a variety of domain applications with the use of components. To increase the reusability of components, they should be developed by analyzing requirements of many different kinds of domains. However, to analyze requirements of a variety of domains related to the components to be developed and to include them inside the components will give burden to developers. Also, providing only general components that have common facilities for the several domains is not easy to accomplish the time-to-market since there are other domains that the developers have to develop. As such, developing common component through the analysis of several domains at the time of the CD (Component Development) does not always guarantee high reusability of the component, but gives burden to developers to develop another development since such components have common functions. Considering this, this paper proposes the component customization technique to reuse common components as well as special components. The reusability of the component can be increased by providing changeability of the attribute, behavior and message flow of the component. This customization technique can change the message flow to integrate developed components or to provide new functions within the component. Also, provides a technique to replace the class existing within the component with other class or to exchange the integrated component with the component having a different function so that requirements from a variety of domains may be satisfied. As such, this technique can accept the requirements of several domains. As such, this customization technique is not only the component with a common function, but it also secures reusability components in the special domain.

• Earthquakes and Structures
• /
• v.16 no.2
• /
• pp.221-234
• /
• 2019

Today, many important concrete face rockfill dams (CFRDs) have been built on the world, and some of these important structures are located on the strong seismic regions. In this reason, examination and monitoring of these water construction's seismic behaviour is very important for the safety and future of these dams. In this study, the nonlinear seismic behaviour of Ilısu CFR dam which was built in Turkey in 2017, is investigated for various reservoir water heights taking into account 1995 Kobe near-fault and far-fault ground motions. Three dimensional (3D) finite difference model of the dam is created using the FLAC3D software that is based on the finite difference method. The most suitable mesh range for the 3D model is chosen to achieve the realistic numerical results. Mohr-Coulomb nonlinear material model is used for the rockfill materials and foundation in the seismic analyses. Moreover, Drucker-Prager nonlinear material model is considered for the concrete slab to represent the nonlinearity of the concrete. The dam body, foundation and concrete slab constantly interact during the lifetime of the CFRDs. Therefore, the special interface elements are defined between the dam body-concrete slab and dam body-foundation due to represent the interaction condition in the 3D model. Free field boundary condition that was used rarely for the nonlinear seismic analyses, is considered for the lateral boundaries of the model. In addition, quiet artificial boundary condition that is special boundary condition for the rigid foundation in the earthquake analyses, is used for the bottom of the foundation. The hysteric damping coefficients are separately calculated for all of the materials. These special damping values is defined to the FLAC3D software using the special fish functions to capture the effects of the variation of the modulus and damping ratio with the dynamic shear-strain magnitude. Total 4 different reservoir water heights are taken into account in the seismic analyses. These water heights are empty reservoir, 50 m, 100 m and 130 m (full reservoir), respectively. In the nonlinear seismic analyses, near-fault and far-fault ground motions of 1995 Kobe earthquake are used. According to the numerical analyses, horizontal displacements, vertical displacements and principal stresses for 4 various reservoir water heights are evaluated in detail. Moreover, these results are compared for the near-fault and far-faults earthquakes. The nonlinear seismic analysis results indicate that as the reservoir height increases, the nonlinear seismic behaviour of the dam clearly changes. Each water height has different seismic effects on the earthquake behaviour of Ilısu CFR dam. In addition, it is obviously seen that near-fault earthquakes and far field earthquakes create different nonlinear seismic damages on the nonlinear earthquake behaviour of the dam.