• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.439-439
• /
• 2011

기존의 고온에서 제작되는 TiO2 나노 입자를 이용한 염료감응형 태양전지를 저온에서 제작하기 위해 전자 이동층으로 ZnO 나노 입자를 사용하여, 저온($200^{\circ}C$)에서 염료감응태양전지(DSSC)를 제작하였다[1,2]. 상대전극(counter electrode)으로는 RF magnetron sputtering을 사용하여 ITO/glass위에 Pt를 증착하여 태양전지의 특성을 측정하였다. $180^{\circ}C$ 이상에서 hydropolymer가 증발되는 것을 이용하여, ZnO 나노입자와 hydropolymer 혼합한 paste 제작하여 소결 후 ZnO 나노입자 사이에 다공성을 생성시켜 Dye가 잘 침투하여 ZnO 나노입자 표면에 잘 흡착 되도록 하였다[3]. 20 nm 및 60 nm 크기의 ZnO 나노 입자를 사용하여 실험 해본 결과, 20 nm에 비하여 60 nm ZnO 나노입자의 경우 IPCE 값이 약 7% 정도로 높은 전환효율 값을 보였다. 60 nm ZnO 나노입자를 전자 수송층으로 사용한 DSSC 소자에서 단위면적당 흐르는 전류(Jsc), 전압 (Voc), fill factor (ff), 그리고 효율(${\eta}$)의 최대값은 4.93 mA/$cm^2$, 0.56V, 0.40, and 1.12%, 로 보였다.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.116-119
• /
• 2010

Adsorption structures of the self-assembled thin films of $\alpha$-cyano-4-hydroxycinnamic acid (CHCA) anchoring on $TiO_2$ surfaces have been studied by using temperature-dependent diffuse reflectance infrared Fourier-transform (DRIFT) spectroscopy. From the presence of the strong $\nu(COO^-)$ band at ~1390 $cm^{-1}$ along with the disappearance of the OH bands in the carboxylic acid group in the DRIFT spectra at room temperature, CHCA appeared to adsorb onto $TiO_2$ surfaces as a carboxylate form. The absence of the out-of-plane benzene ring modes of CHCA in the DRIFT spectra suggests a rather vertical orientation of CHCA on $TiO_2$. Above ~220$ ^{\circ}C$, CHCA seemed to start to thermally degrade on $TiO_2$ surfaces referring from the disappearance of most vibrational modes in the DRIFT spectra, whereas the $\nu$(C ≡ N) bands were found to remain relatively conspicuous as the temperature increased even up to ~460$^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.392-397
• /
• 2022

We present the structural and optical properties of Au@TiO₂ core-shell microsphere structure prepared by a hydrothermal synthesis method. As a way to improve the efficiency of organic solar cells, the Au@TiO₂ core-shell microsphere was synthesized to use the local surface plasmon resonance (LSPR) phenomenon. The synthesized results were confirmed to have the Au@TiO₂ core-shell structure using a high-resolution transmission electron microscopy. An absorption was observed to occur at 527 nm belonging to the visible light region using a visible light spectroscopy, which supports the LSPR phenomenon. We suggest that the Au@TiO₂ core-shell microsphere is highly likely to be applied to organic solar cells including dye-sensitized solar cells. In addition, we expect it to be widely used not only in the energy but also in the bio as well as in the environmental fields.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.309-311
• /
• 2007

Supramolecules containing double hydrogen bonding sites at their both chain ends were self-polymerized to become solid state polymer and were utilized to improve the efficiency of solid state DSSCs. Hydrogen bonding sites were attached at the chain ends of PEG of Mw=2000, such as pyrimethamine and glutaric acid. The solar cell with the solid state supramolecular polymer electrolyte resulted in the overall energy conversion efficiency of 4.63 % with a short circuit current density $(J_{sc})$ of 10.41 $mAcm^{-2}$, an open circuit voltage $V_{oc}$, of 0.71 V and a fill factor (FF) of 0.62 at one sun condition ([oligomer]:[1-methyl-3-propyl imidazolium iodide (MPII)]:$[I_2]$ = 20 : 1 : 0.19, active area = 0.16 $cm^2$, $TiO_2$ layer thickness = 10 ${\mu}m$). The ionic conductivity of the sol id state electrolyte was $5.11{\times}10^{-4}$ (S/cm). The cell performance was characterized by electrochemical impedance spectroscopy and ionic conductivity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.608-613
• /
• 2013

In this paper, the low-temperature sintering of $TiO_2$ is approached to solve the problem of high temperature sintering which decreases the interconnection between particles or between substrate and particle. $TiO_2$ paste is prepared with Titanium (IV) isopropoxide as the precursor material and calcinate at different conditions (low temperature). In the results, since the changing of temperature and time of sintering, crystalline phase do not change and the intensities of anatase, rutile phase are higher. At $110^{\circ}C$, 7 h sintering condition, crystalline size of anatase and rutile phase are the smallest which are 13.07 and 17.47 nm, respectively. In addition, the highest zeta potential is about 32.77 mV and the repulsive force increases thus leading to the best of the dispersion characteristics between $TiO_2$ particles. Futhermore, DSSCs at that condition exhibits the highest efficiency with the values of $V_{oc}$, $J_{sc}$, FF and ${\eta}$ are 0.69 V, $8.60mA\;cm^{-2}$, 67.93% and 4.06%, respectively.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.23 no.1
• /
• pp.59-66
• /
• 2021

This study aimed to a basic research for the development of dye-sensitized solar cells that the wavelength band required for crop growth is passed, and the wavelength band that is not necessary for crop growth can be used for the generation of electricity. The transmissivity according to the illuminance was about 10% higher in the Blue filter and the Green filter than in the Red filter, but the transmissivity according to the PPFD was about 10% higher in the Red filter and the Blue filter than in the Green filter. In addition, the greenhouse attached with 30% infrared blocking filter was predicted to have a lower air temperature than other greenhouses, but it was investigated that there was no significant difference. Therefore, it was investigated that the application of the infrared cut filter would not be appropriate in a greenhouse that controls the temperature by opening a window. As a result of investigating, it was found that the Green and Blue filter greenhouses had the severe overgrowth and the stems grew weaker. The fresh weight of paprika in the infrared blocking filter greenhouse was the highest at 678.9g, and the growth of Red filter and the control greenhouses was relatively poor. Photosynthetic rate, amount of transpiration, and stomatal conductivity were the infrared blocking filter and control greenhouse higher than others. On the other hand, the water use efficiency did not show a big difference.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.1-7
• /
• 2017

Cobalt silicide was used as a counter electrode in order to confirm its reliability in dye-sensitized solar cell (DSSC) devices. 100 nm-Co/300 nm-Si/quartz was formed by an evaporator and cobalt silicide was formed by vacuum heat treatment at $700^{\circ}C$ for 60 min to form approximately 350 nm-CoSi. This process was followed by etching in $80^{\circ}C$-30% $H_2SO_4$ to remove the cobalt residue on the cobalt silicide surface. Also, for the comparison against Pt, we prepared a 100 nm-Pt/glass counter electrode. Cobalt silicide was used for the counter electrode in order to confirm its reliability in DSSC devices and maintained for 0, 168, 336, 504, 672, and 840 hours at $80^{\circ}C$. The photovoltaic properties of the DSSCs employing cobalt silicide were confirmed by using a simulator and potentiostat. Cyclic-voltammetry, field emission scanning electron microscopy, focused ion beam scanning electron microscopy, and energy dispersive spectrometry analyses were used to confirm the catalytic activity, microstructure, and composition, respectively. The energy conversion efficiency (ECE) as a function of time and ECE of the DSSC with Pt and CoSi counter electrodes were maintained for 504 hours. However, after 672 hours, the ECEs decreased to a half of their initial values. The results of the catalytic activity analysis showed that the catalytic activities of the Pt and CoSi counter electrodes decreased to 64% and 57% of their initial values, respectively(after 840 hours). The microstructure analysis showed that the CoSi layer improved the durability in the electrolyte, but because the stress concentrates on the contact surface between the lower quartz substrate and the CoSi layer, cracks are formed locally and flaking occurs. Thus, deterioration occurs due to the residual stress built up during the silicidation of the CoSi counter electrode, so it is necessary to take measures against these residual stresses, in order to ensure the reliability of the electrode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.412-412
• /
• 2016

염료감응 태양전지(dye-sensitized solar cells, DSSCs)는 식물의 광합성원리와 매우 유사한 작동원리를 갖고 있는 전지이며, 간단한 구조, 저렴한 제조단가, 친환경성 등의 등의 장점으로 인하여 많은 관심을 모으고 있다. 이러한 염료감응 태양전지는 빛을 받아들인 염료분자가 전자-홀 쌍을 생성하며 전자는 반도체 산화물을 통해 이동되고 전해질의 산화환원 과정을 통해 염료 분자가 다시 환원되는 순환메커니즘을 따르고 있다. 일반적으로 염료감응 태양전지는 밴드 갭 에너지가 큰 반도체 산화물을 포함하는 작업전극, 산화환원 반응을 통해 전자를 염료로 보내는 전해질, 환원 촉매역할을 하는 상대전극으로 구성되어 있다. 특히, 상대전극으로는 우수한 촉매특성과 높은 전도성을 갖는 백금이 가장 많이 이용되고 있지만 가격이 비싸고 요오드에 취약하기 때문에 상용화에 큰 장애물이다. 따라서, 백금을 대체하기 위해 저가의 탄소나 고분자에 대한 연구가 활발히 진행되고 있고, 그 중 탄소나노섬유(carbon nanofiber, CNFs)는 높은 표면적과 뛰어난 화학적 안정성으로 촉매효율을 증대시킬 수 있어 촉매물질로서 관심이 높아지고 있다. 본 연구에서는 상대전극에 탄소나노섬유기반 복합체를 합성하였고, 성공적으로 저가격 및 고성능의 염료감응 태양전지를 제작하였다. 이때, 지지체인 탄소나노섬유는 전기방사법을 통해 합성하였으며, 수열합성법을 이용하여 금속산화물을 담지하였다. 이렇게 제작된 탄소나노섬유-Fe2O3 복합체는 scanning electron microscopy, transmission electron microscopy, X-ray diffraction, 그리고 X-ray photoelectron spectroscopy 통해 구조적, 화학적 특성을 평가하였으며 전기화학적 특성 및 광전변환 효율을 분석하기 위해 cyclic voltammetry, electrochemical impedance spectroscopy, 그리고 solar simulator를 사용하였다. 본 학회에서 위와 관련된 더 자세한 사항에 대해 논의할 것이다.

• Membrane Journal
• /
• v.21 no.3
• /
• pp.213-221
• /
• 2011

Using poly(ethylene oxide) (PEO) as a polymer host, poly(ethylene glycol) (PEG) as a plasticizer, potassium iodide and iodine as sources of $I^-/I_3^-$, polymer electrolyte membranes were prepared. Based on the polymer electrolytes, solid-state dye-sensitized solar cell (DSSC)s were fabricated. The content of PEG in the electrolyte was controlled to be 95%. The mole number of KI per 1 mole of EO ([KI]/[EO] ratio) in the electrolyte was changed to be 0.022, 0.044, 0.066 and 0.088. The electrolyte membrane showed wax phase in ambient temperature. The ionic conductivity increased with increasing KI content to reach the maximum value at which [KI]/[EO] ratio is 0.066. After the maximum value, the ionic conductivity decreased with increasing KI content. In the case of DSSC, the Voc decreased continuously with increasing KI content in the polymeric electrolyte membrane. The $J_{SC}$ increased with increasing KI content to show maximum value at which [KI]/[EO] ratio is 0.044. In the higher KI content region, $J_{SC}$ value decreased with increasing KI content.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.632-637
• /
• 2015

Mesoporous $TiO_2$ granules were prepared by spray pyrolysis using nano-sized titania particles which were synthesized by a hydrothermal method, and they were evaluated as the photoanode of dye-sensitized solar cells. To enhance the cell efficiency, nanoparticles within granules were chemically interconnected by adding titanium ethoxide (TEOT) to colloidal spray solution. The resulting titania particles had anatase phase without forming rutile. $TiO_2$ granules obtained showed about 400 nm in size, the specific surface area of $74-77m^2/g$, and average pore size of 13-17 nm. The chemical modification of $TiO_2$ granules by adding TEOT initially to the colloidal spray solution was proved to be an effective way in terms of increasing both the light scattering within photoanode and the lifetimes of photo-excited electrons. Consequently, the light-harvesting efficiency of TEOT-modified granules (${\eta}=6.72%$) was enhanced about 14% higher than primitive nanoparticles.