• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.11
• /
• pp.77-83
• /
• 2010

This paper presents the dual resonance PIFA(Planar Inverted F-Antenna) which satisfies the requirements of the 802.11n standard at both 2.4 GHz and 5 GHz frequency bands. Patch for 2.4 GHz and U-Type slot for 5 GHz were used for dual resonance, respectively. In this paper, the characteristics of an antenna were investigated by varying locations of short plate and feed point, the width of the short plate, the thickness and the location of U-Type slot. To investigate the characteristics of the PIFA, HFSS(High Frequency Structure Simulation) for the simulation was used. And the measurement results of a fabricated PIFA were compared with the simulated ones. The measurement and simulation results show that good dual resonance characteristics as the thickness of U-type slot decreases and when the location of U-type slot is far from the feed point.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.1 s.104
• /
• pp.74-80
• /
• 2006

This paper presents the characteristics of electromagnetic field uniformity in a reverberation chamber that can be used alternatively for the analysis, test and evaluation of electromagnetic interference and immunity. The dual-band diffuser, which can be used at two different frequency bands in a reverberation chamber, is applied, and it is made of two different single-band Schroeder's Quadratic Residue Diffusers. The FDTD method is used to analyze the field characteristics. Compared with single-band diffuser, the dual-band diffuser shows the improvement in not only expansion of test frequency band but also in characteristics of the field uniformity, polarity, power efficiency, and tolerance. Therefore, the reverberation chamber with the dual-band diffuser is a better facility, for the analysis and measurement of electromagnetic interference and immunity, than the reverberation chamber with a single-band diffuser.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.67-75
• /
• 2013

The advantages of the orthogonal frequency division multiplexing (OFDM) are high spectral efficiency, resiliency to RF interference, and lower multi-path distortion. To further utilize vast channel capacity of the multiuser OFDM, one has to find the efficient adaptive subchannel and bit allocation among users. In this paper, we compare the performance of the linear programming dual of the 0-1 integer programming formulation with the existing convex optimization approach for the optimal subchannel and bit allocation problem of the multiuser OFDM. Utilizing tight lower bound provided by the LP dual formulation, we develop a primal heurisitc algorithm based on the LP dual solution. The performance of the primal heuristic is compared with MAO, ESA heuristic solutions, and integer programming solution on MATLAB simulation on a system employing M-ary quadrature amplitude modulation (MQAM) assuming a frequency-selective channel consisting of three independent Rayleigh multi-paths.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1423-1431
• /
• 2010

In this paper, the dual-band compact broad bandpass filter using parallel coupled line is proposed. The proposed filter has reduced size and can be controlled bandwidth. And it is also possible to operate in the dual-band purpose. Futhermore, the inserted bandstop fiilter with T-type configuration is also possible to operate in the same purpose. The dual-band bandpass filter has the first operating frequencies and its bandwidth which are 5.8 GHz and 60 % respectively and the second operating frequency and the bandwidth are 16.2 GHz and 60 % respectively. The insertion loss and the return loss of the first frequency has 0.4 dB and 17.4 dB and the insertion loss and the return loss of the second frequency has 0.62 dB and 19.8 dB, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.13-18
• /
• 2015

This study presents the structure design of antenna to have the dual band characteristics in a desired frequency band through the structural modification of an antenna structure. For the experiment, a wideband crossed planar monopole antenna was used. The target frequency band was set to ISM 2.45GHz/5.8GHz. To give the properties, an additional antenna element was added to the crossed planar monopole antenna, which is a main body of the antenna. And then structural adjustment parameter was set to change the length(shape) of the antenna. Various simulations were conducted to find the dual band characteristics in the desired frequency band. The simulations brought forth the antenna bandwidth above the normal values for ISM 2.45GHz/5.8GHz. The structural adjustment parameter introduced in this study for structural modification of an antenna can be useful in developing an antenna featured with dual band(multiband) characteristics.

• Journal of Navigation and Port Research
• /
• v.32 no.6
• /
• pp.481-487
• /
• 2008

Ship's wireless LAN was in the limelight as equipment of ease, cost reduction, various func tion al i ty. In the paper, a dual-bandpass filter for wireless LAN has proposed, which was designed by using dual-mode square loop resonator with square patch in compliance with 2.4 GHz and 5 GHz band of wireless LAN. The dual-bandpass filter could be designed by adjusting sizes of one perturbation element and three of reference elements in compliance with the frequency bands of 2.4 GHz and 5.8 GHz, Furthermore, new dual-bandpass filter was also designed by adjusting stopband of using open stubs in compliance with the frequency bands of 2.4 GHz and 5.2 GHz. The measured results for the fabricated dual-bandpass filters agreed well with the simulated ones, and hence, it was confirmed that the proposed design method is valid.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.48-48
• /
• 2003

A precision orbit determination (POD) system of low Earth orbiter using the GPS dual frequency measurements has been developed. It is an option of KOMPSAT-2 POD process system. In this research, the orbit determination using the real dual frequency carrier phase measurements of the SAC-C satellite was conducted to verify KOMPSAT-2 POD system reliability. The SAC-C satellite is an international cooperative mission between NASA, the Argentine Commission on Space Activities (CONAE), Centre National d'Etudes Spatiales (CNES or the French Space Agency), Instituto Nacional De Pesquisas Espaciais (Brazilian Space Agency), Danish Space Research Institute, and Agenzia Spaziale Italiana (Italian Space Agency). The SAC-C was launched at November 21, 2000. The altitude of SAC-C is 702 km and it carries a TurboRogue III GPS and four high gain antennas developed by the JPL. The receiver is able to generate the dual frequency code and carrier phase data. Double-differenced carrier phase measurements were formed using 25 IGS stations. The data were sampled at 30 seconds interval. Fully dynamic approach was adopted for POD. The POD results were compared with those of JPL using GOA n software. The comparison verifies that deci-meter level 3D position accuracy of low Earth orbiting satellite could be achieved. The POD system has been developed successfully.

• Journal of Advanced Navigation Technology
• /
• v.17 no.4
• /
• pp.396-403
• /
• 2013

Recently, GNSS users can utilize various navigation satellite thanks to GPS modernization, renewal of GLONASS, and development of Galileo and Beidou. And availability performance of users is expected to be improved because these new navigation satellites transmit L5 signal as well as L1 signal, and users can directly estimate the ionospheric delays. In accordance with these changes existing Satellite Based Augmentation System (SBAS) which considers only GPS L1 signal is being developed to support dual frequency and multi-constellation GNSS users. This paper describes the main features of dual-frequency, multi-constellation SBAS algorithms and estimates the performance in Korean region by simulation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.472-472
• /
• 2011

The capacitive coupled plasma (CCP) has been extensively used in the semiconductor industry because it has not only good uniformity, but also low electron temperature. But CCP source has some problems, such as difficulty in varying the ion bombardment energy separately, low plasma density, and high processing pressure, etc. In this reason, dual frequency CCP has been investigated with a separate substrate biasing to control the plasma parameters and to obtain high etch rate with high etch selectivity. Especially, in this study, we studied on the etching of $SiO_2$ by using the pulse-time modulation in the dual-frequency CCP source composed of 60 MHz/ 2 MHz rf power. By using the combination of high /low rf powers, the differences in the gas dissociation, plasma density, and etch characteristics were investigated. Also, as the size of the semiconductor device is decreased to nano-scale, the etching of contact hole which has nano-scale higher aspect ratio is required. For the nano-scale contact hole etching by using continuous plasma, several etch problems such as bowing, sidewall taper, twist, mask faceting, erosion, distortions etc. occurs. To resolve these problems, etching in low process pressure, more sidewall passivation by using fluorocarbon-based plasma with high carbon ratio, low temperature processing, charge effect breaking, power modulation are needed. Therefore, in this study, to resolve these problems, we used the pulse-time modulated dual-frequency CCP system. Pulse plasma is generated by periodical turning the RF power On and Off state. We measured the etch rate, etch selectivity and etch profile by using a step profilometer and SEM. Also the X-ray photoelectron spectroscopic analysis on the surfaces etched by different duty ratio conditions correlate with the results above.

• Journal of information and communication convergence engineering
• /
• v.6 no.3
• /
• pp.305-309
• /
• 2008

This paper presents an innovative prototype of a new conceptual electromagnetic induction eddy current based fluid heating appliance using voltage-fed quasi resonant zero voltage soft switching PWM high-frequency inverter using IGBTs, which can operate at a constant frequency variable power regulation scheme. The promising simple high efficient low noise inverter type electromagnetic induction eddy current based pipeline fluid heating appliance is proposed for saturated steam generator, superheated steam generator, hot water and hot air producer, metal catalyst heating for exhaust gas cleaning in engine. Under these technological backgrounds, a novel electromagnetic induction eddy current Dual Packs Heater(DPH) based pipeline fluid heating incorporates thin metal layer type package for continuous fluid heating appliances applying two types of voltage-fed quasi load resonant ZVS-PWM high frequency inverter. The unique features of a novel electromagnetic induction eddy current DPH based continuous pipeline fluid heating appliance is illustrated on the basis of simulation and discussed for the steady state operating characteristics and experimental results.