• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.421-424
• /
• 2007

Dry sliding wear behavior of ultra-fine grained (UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.149-152
• /
• 2006

Dry sliding wear behavior of low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the dual phase steel was compared with that of a plain carbon steel which was normalized at $950^{\circ}C$ for 30min and then air-cooled. Dry sliding wear tests were carried out using a pin-on-disk type tester at various loads of 1N to 10N under a constant sliding speed condition of 0.2m/sec against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss measured to the accuracy of $10^{-5}g$ by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and a profilomter. Micro vickers hardness values of the cross section of worn surface were measured to analyze strain hardening behavior underneath the wearing surfaces. The were rate of the dual phase steel was lower than the plain carbon steel. Oxidation on the sliding surface and strain hardening were attributed for the higher wear resistance of the dual phase steel.

• 소성∙가공
• /
• 제16권4호
• /
• pp.299-303
• /
• 2007

Dry sliding wear behavior of ultra-fine grained(UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• 대한전자공학회논문지SD
• /
• 제45권5호
• /
• pp.82-87
• /
• 2008

본 논문은 고속 위상 고정이 가능한 새로운 듀얼 슬로프 위상고정루프를 제안한다. 기존의 듀얼 슬로프 위상고정루프는 각각 2개의 전하펌프와 위상 주파수 검출기로 구성되었다. 본 논문에서는 위상차에 따라 전하펌프의 전류를 조절해 하나의 전하펌프와 위상 주파수 검출기만으로 듀얼 슬로프 위상고정루프를 구현하였다. 제안된 회로는 $0.35{\mu}m$ CMOS 공정 파라미터 값으로 HSPICE 시뮬레이션을 수행하여 회로의 동작을 검증하였다. 제안된 듀얼 슬로프 위상고정루프의 위상 고정 시간은 $2.2{\mu}s$로 단일 슬로프 위상고정루프의 위상 고정 시간인 $7{\mu}s$보다 개선된 결과를 얻었다.

• 한국세라믹학회지
• /
• 제44권8호
• /
• pp.424-429
• /
• 2007

Novel conductive $CO_2$ membranes composed of dual phases, molten carbonates and electronic conducting ceramics, were investigated. As the microstructure control of electronic conducting ceramic supports is extremely important to keep the molten carbonates stable in the membranes by a capillary force applied by the pore structure of the supports, we have scrutinized the microstructure of the electronic conducting supports utilizing microscopic images and gas permeability measurement. From the evaluation of the electrical conductivities of the molten carbonates and the electronic conducting ceramic supports, we found that the ionic conductivity of the molten carbonates could determine $CO_2$ flux through the dual phase membranes if the surface exchange rate were relatively high enough.

• 전기학회논문지P
• /
• 제67권2호
• /
• pp.82-89
• /
• 2018

This paper presents a novel prototype of dual mode control based phase shift ZVS PWM high frequency load resonant inverter with lossless snubber capacitors in addition to a single active auxiliary resonant snubber for electromagnetic induction heating(IH) foam metal based consumer fluid dual packs(DPA) heater. The operating principle in steady state and unique features of this voltage source soft switching high frequency inverter circuit topology are described in this paper. The lossless snubber and auxiliary active resonant snubber assisted constant frequency phase shift ZVS PWM high frequency load resonant inverter employing IGBT power modules actually is capable of achieving zero voltage soft commutation over a widely specified power regulation range from full power to low power. The steady state operating performances of this dual mode phase shift PWM series load resonant high frequency inverter are evaluated and discussed on the basis of simulation and experimental results for induction heated foam metal heater which is designed for compact and high efficient moving fluid heating appliance in the consumer pipeline systems.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.275-278
• /
• 1999

In this paper, Dual PFD(Phase Frequency Detector) with improved phase locking time is proposed. The proposed PFD consists of positive and negative edge triggered D flip-flop. In order to confirm the characteristics of proposed PFD, HSPICE simulations are performed using a 0.25${\mu}{\textrm}{m}$ CMOS process. As a result of simulations, the proposed PFD has a characteristic of fast phase locking time with dead zone free.

• 조명전기설비학회논문지
• /
• 제27권6호
• /
• pp.23-30
• /
• 2013

This paper shows the method of winding connection and the balance of three phase of dual inverter systems used for offshore wind power generator. In order to satisfy low cost manufacturing of large scaled wind generator, the number of slot per pole per phase should be reduced. For this reason, in this research, the number is selected as '1' which is the minimum number that stator can have. Based on the prototype machine, three types of machine for the analysis are selected, and various performances especially in terms of electrically balanced condition are also investigated. Moreover, in this paper, new inductance modeling of dual 3-phase considering cross-coupling between two inverter systems is proposed. The several inductances such as mutual-, synchronous inductances are studied. By using FEA, based on calculated the flux linkage of d and q-axis, the validity of the proposed inductance modeling is confirmed.

• 전자공학회논문지A
• /
• 제32A권5호
• /
• pp.14-23
• /
• 1995

A new dual-mode algorithm for blind equalization of quadrature amplitude modulation (QAM) signals is proposed. To solve the problem that the constant modulus algorithm (CMA) converges to the constellation with the arbitrary phase rotation, with the modification of the CMA, the proposed algorithm accomplishes blind equalization and carrier phase recovery simultaneously. In addition, the dual-mode algorithm combining the modified constant modulus algorithm (MCMA) with decision-directed (DD) algorithm achieves the performance enhancement of blind convergence speed and steady-state residual ISI. So we can refer the proposed algorithm to as a scheme for joint blind equalization and carrier phase recovery. Simulation results for i.i.d. input signals confirm that the dual-mode algorithm results in faster convergence speed, samller residual ISI, and better carrier phase recovery than those of the CMA and DD algorithm without any significant increase in computational complexity.

• 한국해양공학회지
• /
• 제6권2호
• /
• pp.85-93
• /
• 1992

The only hardness of 2nd phase of martensite in dual phase steel which was composed of the martensite and ferrite was changed. Fatigue test was conducted by cantilever type of self-made rotated bending fatigue testing machine. The corrosion fatigue fracture behaviors of dual phase steel were investigated in 3% NaCl solution at $N_f$ = $1.5\times$$10^5$ $N_f$=1.0 $\times$ $10^6$ cycles. The fatigue strength was increased with increasing the hardness of 2nd phase. The size and number of corrsion pits were influenced by the 2nd phase hardness and pits remain constant in size just after they were transited into cracks. The life of crack initiation was effected by stress level. The shape of relation of $\Delta$K and da/dn has smaller scattering in it in 3% NaCl solution than that in air. The higher the 2nd phase hardness is, the higher the corrosion fatigue life becomes. Corrosion fatigue fracture behavior was effected by mechanics in case of $N_f$=1.5$\times$10$^5$$N_f$=1.5$\times$10$^6$ cycles.