• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.4
• /
• pp.80-87
• /
• 2014

This paper suggests the dual-gap for generating power and increasing the torque of a direct-drive permanent magnet synchronous motor in a hybrid-cycle. To consider easy coil winding, we applied a structure of dual-gap for the permanent magnet synchronous motor (PMSM). Because the torque of PMSM with the dual-gap is very large, we are designed the appropriate specifications of the PMSM by selected the appropriate dual-gap slot and poles combination. The prototype model is selected by design theory for increasing torque and maximizing output power of PMSM. And the detailed structure design of the model was designed by the loading distribution method. The PMSM models were analyzed by finite element method. Finally, we have suggested appropriate rotor structure has benefit to further increasing torque and prevent decreasing of the output power in PMSM with dual-gap.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.273-277
• /
• 1989

This paper concerns to drive Induction Motor with open delta winding, and improve general performance, speed response, operation region and flexibility of control, etc. And a control algorithm, which reduces large zero-phase current at this operation, is presented.

• Journal of Power Electronics
• /
• v.13 no.5
• /
• pp.806-813
• /
• 2013

This paper aims to compare the performance of three phase induction motor drives using Five Leg Inverter (FLI) and Three Leg Inverter (TLI) configurations. An Indirect Field Oriented Control (IFOC) method using a TLI is well established and incorporated for high performance speed drives in various industries. The FLI dual motor drive system on the other hand shows good workability in the independent control of two induction motor drives simultaneously. In this experiment, the IFOC method is utilized for both drive systems, and Space Vector Pulse Width Modulation (SVPWM) is used to generate pulses for both inverters. For the FLI, the Double Zero Sequence (DZS) Injection technique is used to generate the modulation signal. The complete experiment setup is done by using a DSpace 1103 controller board. The individual motor performances are analyzed using similar schemes, equipment setups and controller parameter values. The results show similar speed performance response capability between the single motor operation using a TLI system and the two motor operation using a FLI system based on the variable speed range either in forward or reverse operation. They also show similar load rejection abilities. However, the single motor with a TLI has a better power quality aspect such as ripple current and total harmonics distortion (THD).

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.107-114
• /
• 2005

With the recent progress in flexible manufacturing systems (FMS) in industry, increasing attention has been given to Automatic Guided Vehicle (AGV) systems. An AGV is a self-powered unit for transporting materials between stations without needing to be controlled by an operator. Such a system has several sensors to recognize the external state, and it is designed to travel between stations automatically without external assistance. To manage each device automatically in real time it requires a distributed controller with a main computer as the host, as well as a number of micro-controllers. In this study, an AGV system with dual motor drive was constructed. A Pentium 4 personal computer was set up as the main host for the distributed control, and this communicated with other micro-controllers in the management of the motor. The speed of each motor was also controlled by a micro-controller.

• Journal of Power Electronics
• /
• v.13 no.2
• /
• pp.250-255
• /
• 2013

This paper proposes an optimal current distribution method of dual-rotor brushless DC machines (DR-BLDCMs) which have inner and outer surface-mounted permanent-magnet rotors. The DR-BLDCM has high power density and high torque density compare to the conventional single rotor BLDCM. To drive the DR-BLDCM, dual 3-phase PWM inverters are required to excite the currents of a dual stator of the DR-BLDCM and an optimal current distribution algorithm is also needed to enhance the system efficiency. In this paper, the copper loss and the switching loss of a DR-BLDCM drive system are analyzed according to the motor parameters and the switching frequency. Moreover, the optimal current distribution method is proposed to minimize the total electrical loss. The validity of the proposed method was verified through several experiments.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.673-676
• /
• 2002

Real time communication is very important in factory automation system using FieldBus. In this paper, we Propose the method to drive dual motors with one controller using CAN In traditional induction motor control technique, two independent Inverters are used to drive dual motors independently. In this case, two controllers are needed. Our proposed dual motors control scheme which use only one microprocessor has many advantages in the view of economic and performance compared to conventional technique.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.564-567
• /
• 1991

In this paper a predictive current control strategy is adopted in the D.C motor drive using dual converter. It is a kind of feedforward control working without overshoot within very short settling time. The difference to the well-known PI current control lies in considering the computer's ability of pre-calcurating the converter's behavior. By simulation it is shown that the predictive current control solve the problems of optimal PI current control, such as overshoot and settling time.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1614-1622
• /
• 2014

A novel equivalent flux sliding-mode observer (SMO) is proposed for dual three-phase interior permanent magnet synchronous motor (DT-IPMSM) drive system in this paper. The DT-IPMSM has two sets of Y-connected stator three-phase windings spatially shifted by 30 electrical degrees. In this method, the sensorless drive system employs a flux SMO with soft phase-locked loop method for rotor speed and position estimation, not only are low-pass filter and phase compensation module eliminated, but also estimation accuracy is improved. Meanwhile, to get the regulator parameters of current control, the inner current loop is realized using a decoupling and diagonal internal model control algorithm. Experiment results of 2MW-level DT-IPMSM drives system show that the proposed method has good dynamic and static performances.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.175-178
• /
• 1991

The drive system of servo motor is requested to have robustness of disturbance and parameter variation. However, the dynamics of PMSM drive change significantly by forced disturbance and parameter variation. Moreover, the state error caused by them should be suppressed completely and rapidly. In this paper, the vector-control system of PMSM using dual adaptive control loop is investigated. In the proposed system, linear adaptive control loop rapidly recovers the state error caused by both disturbance and parameter variation. In the dual adaptive control loop, the inner loop reduces the system sensitivity of parameter variation and disturbance, and the outer loop suppresses the state error caused by them completely. The proposed servo system is verified through a computer simulations and experimental results.