• ETRI Journal
• /
• v.31 no.4
• /
• pp.475-477
• /
• 2009

A balanced dual-band bandpass filter based on ${\lambda}$/2 stepped-impedance resonators and open-loop resonators is proposed in this letter. By employing a type of self-feedback structure, an extra transmission zero is introduced near the common-mode resonance frequency, and the common-mode signal is suppressed. The measured results indicate that the filter can operate in 2.46 GHz and 5.6 GHz bands, and the insertion loss is 1.85 dB and 1.9 dB, respectively. Also, better common-mode suppression is achieved.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.6
• /
• pp.17-24
• /
• 2010

This study was performed to make a close inquiry into a pseudo 3-dimensional structure of the liquid-propellant spray emerging from nonimpinging-type injector. Spray configuration near the injector exit was captured by a high-speed camera, and then its periodic phenomena (shedding) was observed. Detailed spatial structure of spray was investigated by spray characteristic parameters (velocity, diameter, volume flux, etc.) with the aid of a Dual-mode Phase Doppler Anemometry (DPDA). Experiment was carried out at various locations along the geometric axis of the nozzle orifice and on the plane normal to the spray stream with the injection pressures of 17.2 to 27.6 bar.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.64-68
• /
• 2007

Commercial WiBro and 3G HSDPA services are launched last year in order to provide high speed wireless Internet access and multimedia service. Currently mobile communication service providers concentrate on the deployment of indoor mobile network since indoor traffic is remarkably increased. For fine indoor wireless communication, an installation of access point system via Public IP network which is called Femtocell is required. The development of indoor Femtocell system must be considered in the viewpoint of low hardware complexity, cost reduction, interlocking with WiBro/HSDPA network without change of network component and easy element management. In this paper, we review the implementation issue and technology of dual mode AP which provides WiBro and HSDPA signal to the user simultaneously. Especially, we describe on the HSDPA Femtocell standardization status and possible 3 types of HSDPA communication module development design. Furthermore we analyze the merits and demerits of each HSDPA Femtocell design type and propose a system which enables handover between indoor HSDPA Femtocell and outdoor commercial HSDPA mobile network.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.337-340
• /
• 2001

In this paper, we propose two types of dual-mode voltage controlled oscillators (VCO) for PCS/IMT-2000 applications. One is a VCO with controllable resonant circuit. The other type is a VCO with single output and two independent parts

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.2
• /
• pp.321-325
• /
• 2001

In this paper, we propose two types of dual-mode voltage cont.oiled oscillators (VCO) for PCS/IMT-2000 applications. One is a VCO with controllable resonant circuit. The other type is a VCO with single output and two independent parts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.7-11
• /
• 2007

In this paper, we proposed the dual-mode stepped impedance ring resonator bandpass filter for MMIC (Microwave Monolithic Integrated Circuit) applications using the dielectric-supported air-gapped microstrip line (DAML). The ring resonator fabricated by surface micromachining technology. This filter consists of a DAML resonator layer and a CPW feed line. The DAML ring resonator is elevated with $10{\mu}m$ height from GaAs substrate surface. This bandpass filter is $1-{\lambda}g$ type stepped impedance ring resonator including dual-mode resonance. From the measurements, we obtained attenuation of over 15 dB and insertion loss of 2.65 dB at the center frequency of 97 GHz. Relative bandwidth is about 12 % at 97 GHz. Furthermore, the proposed bandpass filter is useful to integrate with conventional MMICs.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.424-429
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.152-162
• /
• 2016

Electrical resistivity tomography (ERT) is a technique to reconstruct the internal resistivity distribution using the measured voltages on the surface electrodes. ERT inverse problem suffers from ill-posedness nature, so regularization methods are used to mitigate ill-posedness. The reconstruction performance varies depending on the type of regularization method. In this paper, an interacting dual-mode regularization method is proposed with two different regularization methods, L1-norm regularization and total variation (TV) regularization, to achieve robust reconstruction performance. The interacting dual-mode regularization method selects the suitable regularization method and combines the regularization methods based on computed mode probabilities depending on the actual conditions. The proposed method is tested with numerical simulations and the results demonstrate an improved reconstruction performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.7
• /
• pp.903-909
• /
• 2014

As a direct drive type washing machine requires two operating modes, washing and spinning modes, a design of the motor with high efficiency in each mode is not applicable to a conventional procedure. To achieve the requirements, a multi-pole outer rotor type switched reluctance motors are considered. To select a suitable motor type for the application, a static toque is compared based on the FEM analysis. The selected type is obtained for high and wide toque than other types of the motor. Further, the pole shape and arc are optimized to meet the required torque and torque ripple. To verify the proposed structure, the prototype is designed and manufactured. And the simulation and experimental results verify the validity of the proposed structure.