• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.3
• /
• pp.278-283
• /
• 2004

Due to the complex arrangement of frequency plans and spatial overages in modern satellite communications, channels that are non-contiguous in frequency may be amplified by a single power amplifier and transmitted to the ground through one beam. In this paper, a dual-mode canonical filter with dual-passband is presented. The filter adopts dual-mode technique for mass and volume reduction. Canonical structure is adopted for maximum transmission zero realization. To validate the design technique, a 6-pole dual-mode canonical dual-passband filter for Ka-band(30/20 ㎓) satellite transponder is realized. The measured frequency response of the filter shows good agreement with the computed one.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.3
• /
• pp.260-264
• /
• 2008

In this paper, a dual mode baseband analog channel selection filter is described which is designed for the Bluetooth and WCDMA wireless communications. Using the presented current-mode integrator, a dual mode channel selection filter is designed. To verify the current-mode integrator circuit, Hspice simulation using 1.8V Hynix $0.18{\mu}m$ standard CMOS technology was performed and achieved $50.0{\sim}4.3dB$ gain, $2.29{\sim}10.3MHz$ unity gain frequency. The described third-order dual mode analog channel selection filter is composed of the current-mode integrator, and used SFG(Signal Flow Graph) method. The simulated results show 0.51, 2.40MHz cutoff frequency which is suitable for the Bluetooth and WCDMA baseband block each.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1088-1092
• /
• 2018

In this paper, we propose a dual-mode frequency tripler using push-push and stacked FET structures. The proposed circuit can operate either in frequency multiplier mode or in amplifier mode. In the frequency multiplier mode, push-push frequency multiplication is achieved by allowing input signals with particular phase shifts. In the amplifier mode, the device operates as a distributed amplifier to obtain high gain. Also both modes were designed using stacked FET structure. The designed circuit showed frequency tripled output power of 9.7 dBm at 2.4 GHz with the input at 800 MHz. On the other hand, in the amplifier mode, the device showed 8.9 dB of gain to generate 19.5 dBm at 800 MHz.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1527-1529
• /
• 2002

본 논문은 저손실 소형 대역통과 여파기인 기지국용 RF/Microwave 수동소자의 다중 공진 모드(Multi-Mode)에 관한 연구로 한개의 유전체 공진기(Dielectric Resonator)로 두개의 공진 모드(Dual-Mode)를 형성하고 그의 결합량을 조절하여 대역통과 여파기를 설계 및 제작하고, 기지국용 Dual-Mode 대역통과 여파기의 소형화, 경량화를 50%이상 향상시켜 양질의 Dual-Mode 공진 특성을 관찰하였다.

• Advances in Energy Research
• /
• v.8 no.4
• /
• pp.213-222
• /
• 2022

Our overdependence on the limited supply of fossil fuel with the burden of emission as a consequence of its utilization has been a major concern. Biodiesel is emerging as a potential diesel substitution for its similar performance, with the additional benefits of emitting lesser emissions. Due to the easy availability of feedstock for Biogas production, Biogas is studied for its use in CI engines. In this study, we considered Linseed Biodiesel and Biogas to run on dual fuel mode in a CI engine. An energy and exergy analysis was conducted to study the rate of fuel energy and exergy transformation to various other processes. Exergy relocation to exhaust gases was observed to be an average of 5% more for dual fuel mode than the diesel mode, whereas exergy relocation to the diesel mode was observed to be more than the dual fuel modes. Also, exergy loss to exhaust gas is observed to be more than the exergy transferred to cooling water or shaft. The exergy efficiency observed for biodiesel-biogas mode is only lesser by 3% compared to diesel-biogas mode, suggesting Biodiesel can be a substitute fuel for diesel.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.9
• /
• pp.1733-1740
• /
• 2011

In this research, a MEMS vibratory gyroscope with dual-mass system in the sensing mode has been proposed to increase the stability of the device using wide bandwidth. A wide flat region between the two resonance peaks of the dual-mass system removes the need for a frequency matching typically required for single mass vibratory gyroscopes. Bandwidth, mass ratio, spring constant, and frequency response of the dual-mass system have been analyzed with MATLAB and ANSYS simulation. Designed first and second peaks of sensing mode are 5,917 and 8,210Hz, respectively. Driving mode resonance frequency of 7,180Hz was located in the flat region between the two resonance peaks of the sensing mode. The device is fabricated with anodically bonded silicon-on-glass substrate. The chip size is 6mm x 6mm and the thickness of the silicon device layer is $50{\mu}m$. Despite the driving mode resonance frequency decrease of 2.8kHz and frequency shift of 176Hz from the sensing mode due to fabrication imperfections, measured driving frequency was located within the bandwidth of sensing part, which validates the utilized dual-mass concept. Measured bandwidth was 768Hz. Sensitivity calculated with measured displacement of driving and sensing parts was 22.4aF/deg/sec. Measured slope of the sensing point was 0.008dB/Hz.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.5
• /
• pp.45-55
• /
• 2010

While Long Term Evolution-Frequency Division Duplexing (LTE-FDD) is regarded as one of the strong candidates for "4G" wireless broadband access in FDD field, LTE-Time Division Duplexing (TDD) is emerging as one possible migration path for WiMAX-TDD in some cases as well as the migration path for Time Division-Synchronous Code Division Multiple Access (TD-SCDMA). In this paper, we analyze the feasibility of dual mode with LTE-TDD in two combinations: dual mode LTE-FDD/TDD and dual mode Worldwide Interoperability for Microwave Access (WiMAX)-TDD/LTE-TDD. Thanks to the commonality in numerology, terminology, and frame structure between LTE-FDD and LTE-TDD, dual mode LTE-FDD/TDD looks feasible in a cost-effective manner. Thanks to the commonality in scheduling algorithm, control mechanism, and supported spectrum bands, it is shown that dual mode WiMAX-TDD/LTE-TDD looks feasible as well. It should be also noted that the commonality in numerology and frame structure is critical for building a chip while the commonality in algorithms and control mechanisms is critical to make it work.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.10
• /
• pp.53-59
• /
• 1997

In this paper, we present a 20 GHz low-loss dual-mode channel filter designed by using mode matching method. The performance of dual-mode channel filter mainly depends on iris characteristics. Therefore the exact design of iris is the key point to get good frequncy response of the filter. MOde matching technique is widely used ot design several kinds of waveguide filters because it is simple in theory and can easily calculate the scattering matrices at the discontinuities with simple structure like iris coupled filters. Additionally the effect for finite thickness of the iris in the dual-mode cavity iflter is analyzed by te full-wave method, providing the exact filter implementation without trial and error.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.7A
• /
• pp.978-985
• /
• 2000

Blind equalizers recover the transmitted data using statistical characteristics of the signal alone. Among many alternatives, steepest gradient descent type algorithms such as the CMA and Sato algorithm are most widely utilized in practice. In this paper we propose a dual-mode NCMA algorithm, which combines the advantages of the dual mode CMA and Normalized CMA (NCMA) with the dual mode phase recovery algorithm. In addition, we perform computer simulations to demonstrate the performance improvement of the proposed algorithm with a QAM system. Simulation results show that the presented algorithm has a faster convergence speed and smaller steady-state residual error than the CMA and dual-mode CMA.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.41-44
• /
• 1998

Dual mode resonators were fabricated using high temperature superconductor. The deposited material was $Y_1Ba_2Cu_3O_{7-x}$(YBCO) on MgO(100) substrate using pulsed laser deposition. Dual mode resonators were patterned by standard photolithography process and wet etching. At the back-side of the substrate, the ground plane with the metal layer of Ti and Ag was fabricated. The transition temperatures of YBCO films were 85-88 K, and network analyzer was used for testing the performance of the resonators. The input/output feedline angles of each resonator were $60^{\circ}$and $100^{\circ}$. The resonant frequency of resonators was 10 GHz. In this paper, dual mode resonator was fabricated for the application of satellite communication.