• 한국통신학회논문지
• /
• 제31권7C호
• /
• pp.743-754
• /
• 2006

본 논문에서는 두 개의 다른 밀리미터 파장을 적용하는 광전계통의 구조 변경을 시도하고 신호 흡수나 환경적 간섭 왜곡에 취약한 싱글 빔(single beam) 레이저 방식의 단점을 보완한 듀얼 빔(dual beam) 방식의 레이저 레이더 시스템을 제안한다. 본 논문에서 제한 한 듀얼 빔 방식 레이더 시스템은 적은 신호 검파의 신뢰성 측면에서 통계적이며 분석적인 방법으로 제안하여 시스템의 우수성을 입증하고 AWGN 배경 잡음과 흡수 또는 간섭에 의해 레이저 신호의 왜곡이 발생하는 채널환경에서 시뮬레이션을 수행함으로써 신호 검파의 신뢰성 향상이 가능하다는 분석적 결과에 대한 정량적 재검증을 한다.

• 대한기계학회논문집B
• /
• 제28권9호
• /
• pp.1110-1116
• /
• 2004

Experimental measurements of laser-induced ion mobility(LIIM) were performed for ethene/air premixed flames operated near the soot inception point. Soot was ionized using a pulsed laser operated at 532 nm. The ionization signal was collected with a tungsten electrode located in the post-flame region. ionization signals were collected using both a single electrode and dual electrode configuration. Prior LIIM studies have focused on the use of a single biased electrode to generate the electric field, with the burner head serving as the path to ground. In many practical combustion systems, a path to ground is not readily available. To apply the LIIM diagnostic to these geometries, a dual electrode geometry must be employed. The influence of electrode configuration, flame equivalence ratio, and flame height on ionization signal detection was determined. The efficacy of the LIIM diagnostic to detect soot inception in the post-flame region of a premixed flame using a dual electrode configuration was investigated. For the different dual electrode configurations tested, the dual parallel electrode geometry was observed to be most sensitive to detect the soot inception point in a premixed flame.

• 한국기계가공학회지
• /
• 제20권2호
• /
• pp.1-7
• /
• 2021

A computer simulation was performed to study the effectiveness of temperature on the type of laser heat source in the context of the heterogeneous welding of aluminum and copper materials. Three different types of heat sources were used in the computer simulation: 1) Single Beam Straight Scan, 2) Single Beam Wobble Scan, and 3) Dual Beam Straight Scan. Among these sources, dual beam straight scan was found to be the most effective from the viewpoint of heat source control. Because the difference between the melting temperatures of copper and aluminum is approximately 400℃, a clear separation of heating temperature was required, and the dual beam straight scan provided superior controllability in this regard. When using the dual beam, the temperature of the 90:10 split was considerably easier to control than that of the 50:50 split. The optimal offset was calculated to be 4 mm off to the copper side, where the melting temperature and thermal conductivity were higher. In this manner, computer simulation was effectively used for determining the optimal laser beam hear source control without performing an actual laser welding experiment.

• Structural Engineering and Mechanics
• /
• 제75권2호
• /
• pp.133-144
• /
• 2020

This investigation is to study the effect of gravitational field and diffusion on a microstretch thermoelastic medium heating by a non-Gaussian laser beam. The problem was studied in the context of the dual-phase-lag model. The normal mode analysis is used to solve the problem to obtain the exact expressions for the non-dimensional displacement components, the micro-rotation, the stresses, and the temperature distribution. The effect of time parameter, heat flux parameter and gravity response of three theories of thermoelasticity i.e. dual-phase-lag model (DPL), Lord and Shulman theory (L-S) and coupled theory (CT) on these quantities have been depicted graphically for a particular model.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권1호
• /
• pp.153-158
• /
• 2009

Stable and tunable dual-wavelength erbium-doped fiber ring laser(EDFL) using a single fiber Bragg grating(FBG) and two coil heaters is proposed and demonstrated. Installing two identical coils into a single FBG, the FBG is symmetrically divided into two different portions. While a current supply to the coil, the refractive index of the FBG under the coil is changed. The FBG can operate as a joint of two different FBGs. Due to the thermo-optic effect of a fiber, the resonance wavelength split into two peaks. The spacing between two adjacent channels was changed as much as the difference of heating power. It was tuned up to 3 nm of wavelength under the electrical power with a 1000 mW. Moreover, the lasing wavelength can be individually tuned without influencing to the adjacent channel.

• 한국정보통신학회논문지
• /
• 제15권3호
• /
• pp.654-659
• /
• 2011

반도체 레이저의 직접 변조 시에 발생하는 레이저의 주파수 처핑(chirping) 현상을 감소시켜 직접 변조를 하는 레이저 다이오드의 변조 특성을 향상시키기 위하여 이중 전극을 가진 구조의 반도체 레이저를 제안하였다. 이중 전극 레이저는 일반적인 측면 방출형 반도체 레이저와 달리 하나의 광이득 매질에 대하여 전기적으로 전극을 분리한 구조이다. 본 논문에서는 이중 전극 구조의 반도체 레이저를 이용하여 직접 변조시 발생하는 처핑(chirping)과 이에 따른 광신호의 선폭을 감소시킴으로써 단일 전극 구조의 레이저 다이오드와 비교하여 10-Gbps NRZ(non-return-to zero) 신호의 80-km 광전송에 대하여 2.5 dB의 광링크 수신감도 향상을 달성하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.53-55
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using phase locked loop(PLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1838-1840
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using digital phase locked loop(DPLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• Medical Lasers
• /
• 제9권2호
• /
• pp.110-118
• /
• 2020

The non-ablative fractional dual laser is equipped with two types of lasers, 1550 nm and 1927 nm in one device, and was approved by the United States Food and Drug Administration in 2013. The advantages of the non-ablative fractional laser (NAFL) include fewer side effects such as erythema, edema, post-laser pigmentation, and scab formation. Thus, the NAFL is preferred by both practitioners and consumers because it is convenient and safe for use. The 1550 nm erbium glass and 1927 nm thulium lasers are representative NAFLs that have been developed separately and are often used as a single-wavelength laser with proven clinical efficacy in various indications. The 1550 nm wavelength laser penetrates the dermis layer and the 1927 nm wavelength laser is effective for epidermal lesions. Therefore, targeting the skin layer can be easily achieved with both the 1550 and 1927 nm lasers, respectively, or in combination. Clinically, the 1550 nm laser is effective in the treatment of mild to moderate sagging and wrinkles, scars, and resurfacing. The 1927 nm laser improves skin texture and treats skin pigmentation and wounds. It can also be used for drug delivery. The selection and utilization rate of NAFL has been increasing in recent times, due to changes in lifestyle patterns and the need for beauty treatments with fewer side effects and short downtime. In this study, we present a plan for safe and effective laser therapy through a review of literature. Clinical applications of the multifunctional NAFL are also described.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.71-76
• /
• 2013

Gas nitriding is a surface hardening process where nitrogen is introduced into the surface of a ferrous alloy. During fusion welding of nitrided carbon steel, the nitride inside weld metal is dissolved and generates nitrogen gas, which causes porosities - blow holes and pits. In this study, several laser welding processes such as weaving welding, two-pass welding, dual beam welding and laser-arc hybrid welding were investigated to elongate the weld pool to enhance nitrogen gas evacuation. The surface pits were successfully eliminated with elongated weld pool. However blowholes inside the weld metal were effective reduced but not fully disappeared.