• Design & Manufacturing
• /
• 제15권4호
• /
• pp.32-36
• /
• 2021

In this study, the cause of the decrease in transmittance of the outer lens among the causes of the decrease in the amount of light in the automobile headlamp was identified, and the improvement method was selected to determine the effect. The causes of defects that lower the transmittance of the outer lens are divided into a moisture problem and a haze problem. The moisture problem is caused by the temperature difference between the inside and the outside of the head lamp, and the haze problem occurs when the heat inside the head lamp evaporates the haze component contained in the plastic material and attaches it to the outer lens. In order to improve the haze problem that occurs in plastic raw materials, the structures of the bulb light source type headlamp and the LED chip light source type headlamp were analyzed. Among them, the housing material of the LED chip light source type headlamp, which is structurally prone to haze gas, was selected as the test target. In the mass-production injection process of the housing, the drying process was selected as a method to minimize haze gas without adding a separate production process. After extracting a sample every drying time at a constant drying temperature, the sample was put into a haze tester and the residual amount of haze gas was measured. As a result, it was confirmed that the residual amount of Haze gas in the material decreased as the drying time increased.

• 한국식품영양과학회지
• /
• 제45권9호
• /
• pp.1358-1365
• /
• 2016

본 연구에서는 원적외선을 이용하여 1차 열풍건조 한 고추 다진 양념을 건조할 경우 두께, 건조온도와 송풍속도에 따른 건조특성과 건조제품의 색도 변화, 건조 전후 고추 다진 양념의 capsaicinoid 등 품질특성을 분석하여 원적외선 건조 기초 자료를 제시하고자 하였다. 고추 다진 양념의 건조속도는 원적외선 건조온도와 송풍속도가 증가할수록 빨라지고 건조시간이 단축되는 경향을 보였으며, 건조 두께 10 mm 조건이 20 mm 조건보다 빠른 것으로 나타났다. 특히 두께 10 mm, 원적외선 건조온도 $80^{\circ}C$, 송풍속도 0.8 m/s 조건에서 건조시간이 63분으로 건조속도가 가장 빠른 것으로 나타났다. 본 연구에서 검증한 건조모델 중 Page 및 Henderson 모델의 경우 전체적인 건조시간대에서 비교적 잘 일치하는 것으로 나타나, 고추 다진 양념의 원적외선 건조 시 Page 및 Henderson 모델을 이용할 경우 높은 정밀도에서 함수율비 예측이 가능한 것으로 나타났다. 원적외선 건조 후 고추 다진 양념의 색차(${\Delta}E$) 값은 두께 10 mm 조건보다 20 mm 조건에서 증가하는 경향을 보였고, 건조온도 $70^{\circ}C$ 조건에서 약간 높은 것으로 나타났으나 오차 범위로 큰 차이는 나타나지 않았다. 원적외선 건조 후 고추 다진 양념의 적색도(a) 값은 두께 20 mm, 건조온도 $80^{\circ}C$ 조건에서 갈변하는 현상이 심화하는 것으로 나타났다. Capsaicin 함량은 건조 두께가 두껍고, 건조온도가 낮으며, 송풍속도가 느릴수록 감소하는 경향을 보였다. 또한, 모든 조건에서 건조 전 capsaicin 함량인 22.15 mg/100 g에 비해 건조 후 capsaicin 함량이 2.24~4.70 mg/100 g 감소하는 것으로 나타났으며, 두께 10 mm, 건조온도 $80^{\circ}C$, 송풍속도 0.8 m/s 조건에서 감소폭이 작은 것으로 나타났다. Dihydrocapsaicin 함량의 경우에도 원적외선 건조 후 1.05~3.82 mg/100 g 감소하는 것으로 나타났고, 두께 10 mm, 건조온도 $80^{\circ}C$, 송풍속도 0.8 m/s 조건에서 감소폭이 작은 것으로 나타났다. 원적외선 건조 중 에너지 소비량은 송풍속도가 느리고 건조온도가 높을수록 감소하였으며, 건조 두께 10 mm 조건이 20 mm 조건보다 적은 경향을 나타내었다. 또한, 두께 10 mm, 건조온도 $80^{\circ}C$, 송풍속도 0.6 m/s 조건에서 에너지 소비량은 5.08 kWh/kg-water로 가장 적은 값을 보였다. 따라서 고추 다진 양념의 건조시간, 건조 중 변색, capsaicinoid 함량 및 에너지 소비량 등을 고려하면 건조 고추 다진 양념의 고품질화를 위해서는 원적외선 건조온도 $80^{\circ}C$, 송풍속도 0.6 m/s, 두께 10 mm 조건이 적절한 건조조건으로 판단된다.

• 약학회지
• /
• 제43권6호
• /
• pp.793-797
• /
• 1999

Salmonella typhi Ty21a is an attenuated strain of S. typhimurium and used for oral typhoid vaccine. In an attempt to increase the stability of Ty21a manufacturing typhoid vaccine, we studied about the stability of freeze-dried Th21a including additives at various temperature conditions. In order to investigate the freeze-drying rate of Ty21a according to various absorbance, we lyophilized Ty21a by using 8% sucrose as a stabilizer. The optimal freeze-drying rate of Ty21a was appeared when OD (optical density) value of the growth was between 2.5 and 3.0. To investigate the stability of Ty21a at various temperature, the viability was measured after storaging the freeze-dried Ty21a at the room temperature, cold and freezing condition for 1 week. The viability of Ty21a in cold and freezing storage condition was 5 times more stable than in room temperature. To search the most stable additives for the freeze-dried Ty21a, the viability of Ty21a including additives at the various storage condition was estimated. Mannitol and loctose were the most stable additives. Theses results suggest that the OD value of Ty21a growth, low temperature, mannitol and lactose are important factors for the optimal freeze-drying rate, the stable storage and the most stable additives, respectively.

• 한국연초학회지
• /
• 제17권1호
• /
• pp.68-78
• /
• 1995

A study of expanding tobacco includes the steps of adjusting the moisture content of cut tobacco, without the use of exogenous impregnants by contacting the filler with a high velocity gaseous medium at elevated temperature such that heat is rapidly and substantially uniformly transferred from the medium to the filler for a total contact time sufficient to expand the tobacco leaves. Study is disclosed for drying and expanding cut tobacco by introducing the tobacco into an elongated tubular shaped conduit through which steam high temperature 150-35$0^{\circ}C$ and high velocity above the 18m1sec, super steam is recycled. moisture content of shreded tobacco leaves, immediately before treatment within the range of from 10% to 24% and, most preferably, within the range of from 18% to 21%. Expanding rate showed 70% in NC -82(B.3) and 42% in Burley -21(B.1) which is produced in 1993 under this condition. When expanding tobacco expanded tobacco did not change significally, but they were decreased at 27$0^{\circ}C$ very largely. The curtailment of cost price and physical and chemical properties of various items were improved in cigarettes. Key words : Expanding tobacco, Super steam tobacco expansion, Fast drying tobacco, High temperature treat tobacco, Puffing tobacco.

• 한국약용작물학회지
• /
• 제25권2호
• /
• pp.89-94
• /
• 2017

Background: The purpose of improving the quality of oriental medicinal herbs is to contribute to the improvement of the income of farm. The present study investigated the effect of reasonable drying methods, different storage conditions and packageing materials on quality and stability of Scutellaria baicalensis Georgi and for developing GAP (good agricultural practice) guide book. Methods and Results: Three methods of drying Scutellaria baicalensis roots produced over two years were used to estimate loss rate owing to drying, storage, and packaging. The methods of drying were categorized into natural drying (36 - 60 h by sunshine), drying with heat dryer (2 - 10 h), or drying with gas bulk dryer (2 - 10 h). After cleaning, and initial drying for a few days under controlled temperature conditions, the second phase of drying was carried out at 35, 45 and $55^{\circ}C$. Changes in hunter color values and quality under the two studied storage treatments (at $20^{\circ}C$ indoors and at $4^{\circ}C$ in a refigerator) were evaluated. Storage period for 60, 120, and 180 days in three packaging materials, PE (polyethylene package), PP (polypropylene gunnysack), and WP (watertight packing paper) were studied. Conclusions: Initial cleaning, reasonable gas drying and hot air drying, and drying in an oven at 35 and $45^{\circ}C$ after cutting the roots resulted in the lowest loss rates in S. Baicalensis root. Hunter color valuse indicated that stroage of dry roots at room temperature was better than PP packaging, and that cold stroage was better than PE packaging for long-term stability.

• Journal of Biosystems Engineering
• /
• 제3권2호
• /
• pp.100-113
• /
• 1978

Drying grain with conventional artificial drying methods requires great quantities of petroleum fuels. Depletion of fossil fuel increases the need of the utilization of solar energy as an alternative to petroluem fuels for drying grain , an energy intensive agricultural operation. Many techniques for the utilization of solar energy in grain drying have been developed, however, there are many problems in adopting solar energy as an energy sources for drying grain. Futhermore, very little research has been done on solar grain drying in Korea. This study was conducted to evaluate the availability of solar energy for drying of rough rice in Chuncheon, Suweon, and Jinju areas based on 50year meteorological data, and to analyze experimentally the performance of a solar air collector for dying grain, and to find the effects of solar heated air compared to unheated air on the rate of drying and energy consumption required for drying of rough rice. The results of this study was may be summarized as follows ; 1. Monthly average daily total radiation on a horizontal surface in October was 260.6 ly/day for Chuncheon, 240.3 ly/day for Suweon , and 253.4 ly/day for Jinju area, respectively. 2. the ratio of monthly average daily diffuse radiation to daily total radiation on a horizontal surface was approximately 0.41 for Chuncheon, 0.45 for Suweon, and 0.44 for Jinju area, respectively. 3. Although the statistical distribution curves of daily total radiation for the three locations were not identical , the differences among them were not large and may be neglected for many practical purposes. 4. I was estimated that the optimum tilting angle of the collector in October was approximately 46 degrees for Chuncheon and Suweon and 45 degrees for Jinju. 5. The ratio of the total radiation on a optimum tilting plane to that on a horizontal plane was estimated to be 1.36 for Chuncheon, 1.31 for Suweon, and 1.27 for Jinju , respectively. 6. The collection efficiency of the solar air collector ranged from 47. 8 to 51. 5 percent at the air flow rates of 251. 1-372.96 $m^3$/hr. High efficiency remained nearly , constant during the best sunshine hours, 10 a.m. to 2 p.m. and decreased during other hours. More energy was collected as the air flow rate incresed. 7. The average temperature rise in the drying air from the solar collector for the test period varied from $6.5^\circC$ to $21.8^\circC$ above the ambient air temperature. 8. Solar-dried rough rice averaged 13.7 percent moisture (w.b.) after 130 hours of drying with the air flow rate of 1. 64 ccm/$m^3$, and rough rice dried with natural air averaged 15.1 percent moisture (w.b.) after 325 hours of drying with the same air flow rate. 9. Energy saving of 2.4 kwh per $m^3$ percentage point of moisture removed was obtained from solar heated air drYing. The solar bin used 53.3 percent less energy per percentage point of moisture removed than the natural air bin.

• 에너지공학
• /
• 제21권1호
• /
• pp.43-46
• /
• 2012

A fluidized bed drying approach was utilized to the synthesis of water glass based silica aerogel powders. The effects of the fluidized bed drying conditions such as the superficial velocity and temperature of hot air and bead size as well as bead/wet-gel ratio, on the physical properties such as tapping density and productivity of the aerogel powders were systematically investigated. The experimental results showed that the amount of beads mixed with wet-gels in the fluidized bed column has the most profound impact on the fluidization efficiency, greatly enhancing the yield of the aerogel powders up to 98% with a proper bead/wet-gel weight ratio as compared to 72% without using beads. No significant change was observed in the tapping density over a wide range of the fluidized drying condition. Consequently the fluidized bed drying approach shows a good promise as an alternative route for the large-scale production of the aerogel powders.

• 한국가구학회지
• /
• 제19권2호
• /
• pp.116-123
• /
• 2008

Kiln schedule development was based on two schedule phases, the first being to determine the maximum safe kiln temperature during the check prone initial stage of drying, with the second stage determining how to accelerate drying once the danger of checking had passed. This was achieved by using 38 mm thick boards which were pre-screened for susceptibility to internal checking, and then drying matched sample boards over a range of kiln temperatures. Research has shown that below 50% MC there is no further risk of internal checking. However, difference in drying rate due to board width and the increased occurrence of wet patches in wide boards means that it is essential to modify the basic schedule according to the maximum board width. A condition of 52/40 $^{\circ}C$ was selected for the checking-free initial kiln drying step and a 5-step kiln-schedule dried the boards from 109% to 8% MC for 72.5 hours without internal checking.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.151-156
• /
• 2002

Drying shrinkage cracking which may be caused by the relatively large specific surface is a matter of grave concern for latex modified concrete(LMC) overlay and rapid-setting cement latex modified concrete(RSLMC) overlay. LMC and RSLMC were studied for field applications very actively in terms of strength and durability in Korea. However, there were no considerations in drying shrinkage. Therefore, the purpose of this study was to investigate the drying shrinkage properties of LMC and RSLMC with the main experimental variables such as cement types(ordinary portland cement, rapid setting cement), latex contents(0, 5, 10, 15, 20%), W-C ratios, and curing days at a controlled environment of 60% of relative humidity and 2$0^{\circ}C$ of temperature. The drying shrinkage for specimens was measured with a digital dial gauge of Demec. The test results showed that the drying shrinkage of LMC and RSLMC were considerably lower than that of OPC and RSC, respectively. This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.99-102
• /
• 2010

In the present study, a three-dimensional numerical simulation was performed in a paint drying system of vehicle assembly line. In the drying system hot air and cool air are blown in turn from the nozzles to dry the trim of vehicle. Inlet boundary condition using user subroutine code is adopted to consider the moving motion of the vehicle. The present paper aims to improve the performance of the drying system. The transient distribution of temperature and velocity at the surface of the vehicle were predicted numerically. From these results, optimal operating condition of the drying system are to be suggested.