• Journal of Soil and Groundwater Environment
• /
• v.22 no.4
• /
• pp.27-32
• /
• 2017

In this study, a remedial investigation using reductive stabilization was conducted to treat Cr(VI)-contaminated soil. The influences of various operational parameters, including reaction time and the mass of ferrous iron, were also evaluated. The study site was contaminated with a large amount of Cr(III) and Cr(VI), and the selected treatment method was to stabilize Cr(VI) with ferrous iron, which reduced Cr(VI) to Cr(III) and stabilized the chromium, although a greater mass of ferrous iron than the stoichiometric amount was required to stabilize the Cr(VI). However, some Cr(III) re-oxidized to Cr(VI) during the drying process, and addition of a strong reducing agent was required to maintain reducing conditions. With this reducing agent, the treated soil met the required regulatory standard, and the mass of Cr(III) re-oxidized to Cr(VI) was significantly reduced, compared to the use of only Fe(II) as a reducing agent.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.425-430
• /
• 2019

Zinc coatings are widely used because of their environmental friendliness and high performance. In general, the coating temperature is a major factor in determining the coating layer thickness and coating quality. In the case of a zinc coating, a uniform and appropriate coating temperature is required. In this study, a thermal flow simulation of the air flow was performed to analyze the temperature distribution of a zinc spray coating room in a natural convection state. Using SolidWorks, modeling was performed for two spray coating rooms, a preheating room, and a drying room, and a thermal flow coupled analysis was performed using ANSYS-FLUENT. As a result of the analysis, the temperature distribution characteristics in the spray coating rooms were determined. It was found that the present temperature was below the target temperature of $25^{\circ}C$. Simulations were conducted for two different boundary conditions (one with a heater added and another with the open part closed). The simulation results show that the method of closing the open part is better than adding the heater.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.6
• /
• pp.635-641
• /
• 2018

To select the operating condition of 0.5 MWth chemical looping combustion system, minimum fluidization velocity, transition velocity to fast fluidization and solid circulation rate were measured using mass produced new oxygen carrier (N016-R4) which produced by spray drying method for 0.5 MWth chemical looping combustion system. A minimum fluidization velocity decreased as the pressure increased. The measured transition velocity to fast fluidization was 2.0 m/s at ambient temperature and pressure. The measured solid circulation rate increased as the solid control valve opening increased. We could control the solid circulation rate from 26 to $93kg/m^2s$. Based on the measured minimum fluidization velocity and transition velocity to fast fluidization, we choose appropriate operating conditions and demonstrated continuous solid circulation at high pressure condition (5 bar-abs) up to 24 hours.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.3
• /
• pp.112-121
• /
• 2019

In this study, silicon / carbon nanotube / carbon composite particles with high capacity were fabricated by using micro-sized silicon particles and carbon nanotubes as an anode material for lithium ion batteries. The silicon / carbon nanotube / carbon composite particles were prepared by spray drying method to prepare spherical composite particles. The composite particles have the network structure of the carbon nanotubes around the silicon particles, in which the silicon particles and the carbon nanotubes are bonded by amorphous carbon. It appears that the volume expansion of silicon is effectively buffered and the electrical contact is maintained in the network structure of the composite particles during charge-discharge cycles.

• Journal of the Korean Geosynthetics Society
• /
• v.20 no.4
• /
• pp.9-18
• /
• 2021

In this study, the overconsolidation ratio (OCR) of soft clay soil was calculated by conducting an indoor physical experiment and a dynamics test using undisturbed soil samples from a soft clay soil field in South Korea. The OCR by depth was predicted by comparing the experimental results with the existing empirical equations. Methods using the liquidity index and the existing empirical equation by the Naval Facilities Engineering Systems Command (NAVFAC) were examined, and the results were compared with the actual measured values. The method using the liquidity index was found to be suitable for estimating the rough OCR of the ground. However, the effect of drying was not considered for the ground above the groundwater level. Therefore, an equation for the correlation equation between the depth and OCR of each region, including the ground above the groundwater level, was proposed. The proposed equation was applied to the OCR prediction of the adjacent area. The predicted values in the area composed of clay (CL, CH) were found to be in good agreement with the actual values. In the region composed of silt (ML), however, the predicted values were not consistent with the actual values. This suggests that the sedimentation and compositional characteristics, rather than the engineering characteristics of the soil, are important factors that affect the OCR prediction.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.367-372
• /
• 2022

The effect of the addition of a polyvinylchloride (PVC) non-solvent to a PVC-tetrahydrofuran (THF) solution on the surface properties of the PVC thin film was analyzed. The non-solvents used were composed of alcohol-based and non-alcoholic ones. Surface morphologies of PVC thin films according to the addition of the non-solvent were compared. In addition, the hydrophobic properties relying on the surface characteristics were compared. The micro-bubbles generated in the preparation of PVC-THF solution affected the surface morphology of the thin film. In order to implement the normal surface physical properties of the coating thin film at the relatively high concentration of PVC-THF solution, the selection of appropriate drying method was required. When an alcohol-based non-solvent was added, a PVC thin film having a granular porous surface was obtained and exhibited super hydrophobic properties. The volume ratio of the PVC-THF solution to the non-solvent affects the surface shape of the coating thin film. The larger the amount of non-solvent was added, the more advantageous it was to form a super hydrophobic PVC thin film.

• Geomechanics and Engineering
• /
• v.33 no.1
• /
• pp.29-40
• /
• 2023

Xanthan gum and starch compound biopolymer (XS), an environmentally friendly soil-binding material produced from natural resources, has been suggested as a slope protection material to enhance soil strength and erosion resistance. Insufficient wet strength and the consequent durability concerns remain, despite XS biopolymer-soil treatment showing high strength and erosion resistance in the dried state, even with a small dosage of soil mass. These concerns need to be solved to improve the field applicability and post-stability of this treatment. This study explored the utilization of an alkaline-based cation crosslinking method using calcium hydroxide and sodium hydroxide to induce non-thermal gelation, resulting in the enhancement of the wet strength and durability of biopolymer-treated soil. Laboratory experiments were conducted to assess the unconfined compressive strength and cyclic wetting-drying durability performance of the treated soil using a selected recipe based on a preliminary gel formation test. The results demonstrated that the uniformity of the gel structure and gelling time varied depending on the ratio of crosslinkers to biopolymer; consequently, the strength of the soil was affected. Subsequently, site soil treated with the recipe, which showed the best performance in indoor assessment, was implemented on the field slope at the bridge abutment via compaction and pressurized spraying methods to assess feasibility in field implementation. Moreover, the variation in surface soil hardness was monitored periodically for one year. Both slopes implemented by the two construction methods showed sufficient stability against detachment and scouring, with a higher soil hardness index than the natural slope for a year.

• Journal of the Korean Society of Food Culture
• /
• v.22 no.2
• /
• pp.261-265
• /
• 2007

The antidepressant effects of Cirsium japonicum was revealed in previous studies using open field test and forced swimming test. The contents of total flavonoids and apigenin of Cirsium japonicum were analyzed and sensory evaluation of Cirsium japonicum tea was performed in order to develop Cirsium japonicum tea as an antidepressant. Among the different plant parts of Cirsium japonicum, leaves had the highest level of total flavonoids and apigenin contents and were followed by flowers and stems. Drying method affected total flavonoids and apigenin content of Cirsium japonicum, but regular pattern was not revealed. In sensory evaluation, overall acceptance of Cirsium japonicum flower-leaf mix tea was higher than those of Cirsium japonicum leaf tea. Also purchase intention of Cirsium japonicum flower-leaf mix tea was higher than those of Cirsium japonicum leaf tea.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5D
• /
• pp.813-819
• /
• 2006

Skid Resistance is a index to represent the friction between tire and road surface, which influences driving safety. Skid resistance varies with the conditions of tire, abrasion of road surface, vehicle speed, drying, wet and freezing condition of road surfaces. Especially, freezing occurs when temperature drops below $0^{\circ}C$ followed by snow or rain causes decrease of skid resistance. To recover the decreased skid resistance deicing work is applied. As a results of deicing works, freezing condition is changed into wet condition. However the wet road surfaces containing the remaining deicings agents may not show the skid resistance of normal wet condition. In this study, skid resistances in the condition of freezing, deicing process and deicing agents remained after snow-removal are evaluated. The test results, skid resistance recover quickly when Pre-wetted salt spreading and NaCl was used as deicing method. Skid resistance of Deicing agents remained on the road surface showed that concrete is higher than asphalt. superior effect. Recovery rate of skid resistance by comparison wet condition is 54~80%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.178-189
• /
• 1994

Fine $BaTiO_3$ powder was synthesized from the various starting solution with 0.05 M by ultrasonic spray pyrolysis method. The conditions of synthesis were fixed on flow rate was 0.5 cm/sec, low temperature furnace was $300^{\circ}C$, and high temperatures furnace was $700^{\circ}C$. The formation procedure was investigated directly by SEM with the collected particle from the each reaction step. Also, the trace of particle in reaction tube was researched theoretically. Fine $BaTiO_3$ was synthesized only in the case of nitrate aqueous solution. The synthesized $BaTiO_3$ powder was porous and spherical which was consist of primary particle at the size of 19.1 nm. The formation procedure was as follows : the particle size decreased in drying step and then increased in initial thermal decomposition step. Finally, particle size was decreased to $0.42 {mu}m$. The trace of particle in reaction tube was also theoretically simulated and discussed.