• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.1
• /
• pp.44-49
• /
• 2013

Hydrogen penetration into a metal leads to damages and mechanical degradations and its content measurement is of importance. For a precise measurement, a sample preparation procedure must be optimized through a series of studies on sample washing and drying. In this study, two-step washing with organic solvents and thermal soaking in inert gas were tried with a rod-shaped, API X65 steel sample. The samples were machined from a steel plate and then washed in acetone and etyl-alcohol for 5 minute each and dried with compressed air. After then, the samples were thermally soaked in a home-made nitrogen gas chamber during 10 minute at different heat gun temperatures from 100 to $400^{\circ}C$ and corresponding temperature range in the soaking chamber was from 77 to $266^{\circ}C$ according to the temperature calibration. Hydrogen residue in the samples was measured with a hot extraction system after each soaking step; hydrogen residue of $0.70{\pm}0.12$ wppm after the thermal soaking at $77^{\circ}C$ decayed with increase of the soaking temperature. By adopting the heat transfer model, decay behavior of the hydrogen residue was fitted into an exponential decay function of the soaking temperature. Saturated value or lower bound of the hydrogen residue was 0.36 wppm and chamber temperature required to lower the hydrogen residue about 95% of the lower bound was $360^{\circ}C$. Furthermore, a thermal desorption spectroscopy was done for the fully soaked samples at $360^{\circ}C$. Weak hydrogen peak was observed for whole temperature range and it means that hydrogen-related contaminants of the sample surface are steadily removed by heating. In addition, a broad peak found around $400^{\circ}C$ means that parts of the hydrogen residue are irreversibly trapped in the steel microstructure.

• Restorative Dentistry and Endodontics
• /
• v.12 no.2
• /
• pp.45-53
• /
• 1987

The purpose of this study was to evaluate the tensile bond strength between composite resin and the human enamel. Three composite resin systems, two chemical (Clearfil Posterior, and Clearfil Posterior-3) and one light cure (Photo Clearfil-A), used with and without an intermediate resin (clearfil bonding agent), were evaluated under different amounts of load (10g, 200g and 200g for a moment) for in vitro tensile bond strength to acid-eched human enamel. Clinically intact buccal or lingual surfaces of 144 freshly extracted human permanent molars, embedded in acrylic were flattened with No #600 carborundum discs. Samples were randomly assigned to the different materials and treatments using a table of random numbers. Eight samples were thus prepared for each group(Table 2) these surfaces were etched with an acid etchant (Kurarey Co. Japan) in a mode of etching for 30 seconds, washing for 15 seconds, and drying for 30-seconds. During the polymerization of composite resin on the acid-etched enamel surfaces with and without bonding agent 10-gram, 200 gram and temporary 200 gram of load were applied. The specimens were stored in 50% relation humidity at $37^{\circ}C$ for 24 hours before testing. An universal Testing machine (Intesco model No. 2010, Tokyo, Japan) was used to apply tensile loads in the vertical directed (fig 5), and the force required for separation was recorded with a cross head speed of 0.25 mm/min and 20 kg in full scale. The results were as follow: 1. The tensile bond strength was much greater in applying a bonding agent than in not doing that. 2. The tensile bond strength of chemical cure composite resin was higher than that of light cure composite resin with applying on bonding agent on the acid-etched enamel. 3. In case of not applying a bonding agents on the acid-etching enamel, the highest tensile bond strength under 200 gram of load was measured in light cure composite resin. 4. The tensile bond strength under 200-gram of load has no relation with applying the bonding agent. 5. Under the load of 10-gram, There was significant difference in tensile bond strength as applying the bonding agent.

• Food Engineering Progress
• /
• v.14 no.2
• /
• pp.112-117
• /
• 2010

Black ginger, obtained from steaming and drying process, provides the various functional properties. This study was performed to investigate the optimum processing conditions for black ginger with high content of biologically active substance such as anti-oxidations. Optimum processing conditions such as temperature and time for black ginger was determined by response surface methodology (RSM) with manufacturing process and functionality. The optimum steaming condition was determined 6 hours at 93.2$^{\circ}C$, and 82.7 mg/L DPPH scavenging activities was obtained at this condition. The black ginger drink was made with black ginger extracts, Japanese apricot, and honey. Interaction effects of these ingredients were investigated by modified distance based on design and analyzed by linear, nonlinear regression model, and RSM. The optimization of mixture ratio was made by statistical modeling using DPPH scavenging activities and sensory properties which are the important target constraints in drink. Total flavonoids showed a linear canonical form, while preference and antiradical activity showed a nonlinear canonical form indicating the higher interaction among mixtures. The response trace plot revealed that antiradical activity, sensory properties and total flavonoids were quite sensitive to the drink blending. The optimum formulation of the drink was set at 14.2% of black ginger extracts, 5% of Japanese apricot, and 10.8% honey.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.54 no.6
• /
• pp.869-879
• /
• 2021

Methods for the development of home meal replacement seafood tailored to consumer needs for the advanced use of Broughton's ribbed ark Scapharca broughtonii (BRA) in Korea are required. In this study, we developed a cheese-topped, semi-dried, and seasoned Broughton's ribbed ark (S-BRA) tailored for the younger generation with an improved texture and fish odor. The optimization of conditions to improve the texture and fish odor was performed using RSM. The design of the model was appropriate because there was no significant difference (P>0.05) between the predicted and actual values of moisture content, hardness, and overall acceptance, and the optimal preparation conditions were a vinegar content of 2.68%, a soaking time of 62 min, a drying temperature of 60℃, and a time of 162 min. The S-BRA manufactured under these optimal conditions exhibited a lower odor intensity compared to the unsoaked and undried control, suggesting that the fish odor of S-BRA has been improved. The moisture content related to the texture of the S-BRA was lower than that of the control, and the hardness was higher. Therefore, the S-BRA developed in this study will appeal to people of all ages, especially the younger generation; their consumption is expected to increase.

• Journal of Korean Academy of Dental Administration
• /
• v.6 no.1
• /
• pp.19-27
• /
• 2018

The purpose of this study was to determine the level of toothbrush bacterial growth, whether the dryness of the toothbrush head differs depending on the number of holes in the head, and to use these results as a reference for future toothbrush design. Two-millimeter holes were created on the head of the toothbrushes in groups of three, one, or zero holes. We made the solution with Streptococcus mutans, and the toothbrushes were placed in the solution and agitated. The toothbrushes were shaken to remove moisture and allowed to air-dry. The toothbrush heads were swabbed with saline and then placed in two inoculation groups. The first group was inoculated with a 102 dilution of the S. mutans culture and the second was inoculated with the original culture. After incubation, bacterial colony numbers were measured. The number of holes on the toothbrush head correlated with a decrease in number of cultured bacterial colonies. Our model of a toothbrush head with holes indicated that these holes in the toothbrush head were effective in reducing the level of microbial contamination and that a greater number of holes creates an improved toothbrush sanitation effect. The average number of colonies on the head of toothbrush by number of holes was high, followed by the number of holes 0, 1 and 3, and the average number of colony among toothbrush heads was same. The use of a toothbrush with holes between the toothbrush head indicates that it is effective in reducing the level of microbial contamination between the toothbrush head and toothbrush and the higher the number of holes, the better the effect.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4A
• /
• pp.373-384
• /
• 2009

For the first step on the quantitative evaluation of shrinkage reduction and differential shrinkage analysis of lightweight aggregate concrete, this study sets the moisture transport model of concrete by pre-absorbed water of porous lightweight aggregates and measured effective moisture diffusion coefficient, moisture capacity, degree of humidity supply and degree of humidity consumption by water binder ratio and aggregate type. The effective moisture diffusion coefficient in steady state caused by humidity difference between inside and outside of concrete had low value as low water-binder ratio. And in case of same water-binder ratio, effective moisture diffusion of mixtures used normal aggregates were lower than those used lightweight aggregates. To determine moisture store capability of concrete - moisture capacity, moisture contents were measured in 9 humidity conditions. As a result moisture contents of mixtures used lightweight aggregates was higher than mixtures used normal aggregates in all humidity conditions. This study measured lightweight aggregates' degree of humidity supply that applicable to normal atmospheric environment (above RH 50%) and made it quantitatively. Also amount of moisture release was set as a exponential function that represents a clear trend proportion to time and inverse proportion to humidity of the surroundings. As the result of measurement about degree of moisture consumption inside concrete following the internal consumption caused by cement hydration self-drying, it was showed that rapid decrease of humidity, around 10%, at early ages (7~10 days) when water-binder ratio is 0.3 and slow decrease around 5% and 1% when water-binder ratio is 0.4 and 0.5.

• Journal of Korean Academy of Nursing
• /
• v.24 no.4
• /
• pp.597-615
• /
• 1994

This study is designed to facilitate the creation of home environment conducive to the family taking care of chronic bed-ridden patients with more effective method. The need for this study has emerged against the background of marked changes in the structure of ailments and causes of death, resulting in the number and plights of chronic bed-ridden patients as well as of a rapid increase in demand for medical care and resulting premature discharge. Keeping these in mind, this study focused on home-wards where the majority of chronic bed-ridden patients are being cared for. Despite. their overriding importance, home-words are less than efficient in caring (or chronic bed-ridden patients. These circumstances require the designing of home-wards that can offer greater comfort to patients and at the same time make things easier for caregivers, on the basis of an overall analysis of patients' life and home - ward situation. According1y this study adopted a Participant Observation Method derived cultural anthropology, Toward this end, 3 patients were chosen as subjects of this study for intensive interviewing and participant observation. In the process of this field re-search efforts were made to collect emprical data, that is, to faithfully record the words of the subjects and their caregivers for analysis and interpretation. The findings of these analyses are as follows. Firstly, the chronic bed-ridden patients are mostly being taken care by close family members. Secondly, a room for the exclusive use of the patient, floor, kitchen, bathroom and multipurpose space were found to be necessary for proper caring of the patient. These spaces were respectively used with a view to 1) accomodating the patient as well as caregivers' activities, 2) keeping general and medical supplies and other appliances for patient's care and drying the patient's washing, 3) preparing and keeping the patient's foods and beverages, 4) keeping the supplies necessary for cleaning the patient's body and treating the patient's eliminations, 5) washing the patient's clothes, underwears and bedclothes. The patient's room in turn is subdivided into six portions in terms of uses : specifically the places for accomodating 1) the patient, 2) medical supplies, 3) medicines, 4) linens St clothes, 5) bedclothes and, 6) diapers. Thirdly, the activities of the caregiver are subdivided into seven key areas : hygiene, exercise, diet, elimination, therapeutic nursing, prevention of sore, and other activities. Each area is further classified into several different activities of caring. These activities we mainly carried out in the patient's room. Fourthly, the supplies for caring the chronic bed-ridden patient is divided into two large domains : medical and general supplies. Finally, three main problems areas were found in this study on the part of caregivers, that is, sore prevention, hygiene problem related frequent urination / defecation, the caregiver's physical, psych ological and emotional burden. In consideration of the aforesaid problem areas, a model home-ward was developed in this study. The newly-developed model has been found to have the following six advantages. Firstly, the time and effort required for maintaining the patient's hygiene are reduced, thus relievins the caregiver's physical and psychological bur-den. Secondly, the patient's hygiene can be maintained in satisfactory conditions, because the patient's eliminations are more easily removed. Thirdly, skin irritations caused by the patient's eliminations were remarkably reduced and so were the patient's sores due to moisture and bacteria. Fourthly, the home-ward have a tilt-table ef-fect thanks to the inclining room floor. This improves the patient's cardiovascular function as well as constantly changes pressed skin areas and thus prevents sores. Fifthly, improved shelf arrangements help make the best use of patient's supplies. Sixthly, the trouble of continuously changing clothes, underwears, diapers & bedclothes is remarkably reduced simply by covering the patient with cotton sheets when laid in bed. This is espected to cut down expenses by reducing the comsumptions of diapers and other disposable supplies.

• Korean Journal of Agricultural Science
• /
• v.14 no.1
• /
• pp.98-133
• /
• 1987

The mechanical and rheological properties of agricultural materials are important for engineering design and analysis of their mechanical harvesting, handling, transporting and processing systems. Agricultural materials, which composed of structural members and fluids do not react in a purely elastic manner, and their response when subjected to stress and strain is a combination of elastic and viscous behavior so called viscoelastic behavior. Many researchers have conducted studies on the mechanical and rheological properties of the various agricultural products, but a few researcher has studied those properties of rice plant, and also those data are available only for foreign varieties of rice plant. This study are conducted to experimentally determine the mechanical and the rheological properties such as axial compressive strength, tensile strength, bending and shear strength, stress relaxation and creep behavior of rice stems, and grain detachment strength. The rheological models for the rice stem were developed from the test data. The shearing characteristics were examined at some different levels of portion, cross-sectional area, moisture content of rice stem and shearing angle. The results obtained from this study were summarized as follows 1. The mechanical properties of the stems of the J aponica types were greater than those of the Indica ${\times}$ Japonica hybrid in compression, tension, bendingand shearing. 2. The mean value of the compressive force was 80.5 N in the Japonica types and 55.5 N in the Indica ${\times}$ Japonica hybrid which was about 70 percent to that of the Japonica types, and then the value increased progressively at the lower portion of the stems generally. 3. The average tensile force was about 226.6 N in the Japonica types and 123.6 N in the Indica ${\times}$ Japonica hybrid which was about 55 percent to that of the Japonica types. 4. The bending moment was $0.19N{\cdot}m$ in the Japonica types and $0.13N{\cdot}m$ in the Indica ${\times}$ Japonica hybrid which was 68 percent to that of the Japonica types and the bending strength was 7.7 MPa in the Japonica types and 6.5 MPa in the Indica ${\times}$ Japonica hybrid respectively. 5. The shearing force was 141.1 N in Jinju, the Japonica type and 101.4 N in Taebaeg, the Indica ${\times}$ Japonica hybrid which was 72 percent to that of Jinju, and the shearing strength of Taebaeg was 63 percent to that of Jinju. 6. The shearing force and the shearing energy along the stem portion in Jinju increased progressively together at the lower portions, meanwhile in Taebaeg the shearing force showed the maximum value at the intermediate portion and the shearing energy was the greatest at the portion of 21 cm from the ground level, and also the shearing strength and the shearing energy per unit cross-sectional area of the stem were the greater values at the intermediate portion than at any other portions. 7. The shearing force and the shearing energy increased with increase of the cross-sectional area of the rice stem and with decrease of the shearing angie from $90^{\circ}$ to $50^{\circ}$. 8. The shearing forces showed the minimum values of 110 N at Jinju and of 60 N at Taebaeg, the shearing energy at the moisture content decreased about 15 percent point from initial moisture content showed value of 50 mJ in Jinju and of 30 mJ in Taebaeg, respectively. 9. The stress relaxation behavior could be described by the generalized Maxwell model and also the compression creep behavior by Burger's model, respectively in the rice stem. 10. With increase of loading rate, the stress relaxation intensity increased, meanwhile the relaxation time and residual stress decreased. 11. In the compression creep test, the logarithmic creep occured at the stress less than 2.0 MPa and the steady-state creep at the stress larger than 2.0 MPa. 12. The stress level had not a significant effect on the relaxation time, while the relaxation intensity and residual stress increased with increase of the stress level. 13. In the compression creep test of the rice stem, the instantaneous elastic modulus of Burger's model showed the range of 60 to 80 MPa and the viscosities of the free dashpot were very large numerical value which was well explained that the rice stem was viscoelastic material. 14. The tensile detachment forces were about 1.7 to 2.3 N in the Japonica types while about 1.0 to 1.3 N in Indica ${\times}$ Japonica hybrid corresponding to 58 percent of Japonica types, and the bending detachment forces were about 0.6 to 1.1 N corresponding to 30 to 50 percent of the tensile detachment forces, and the bending detachment of the Indica ${\times}$ Japonica hybrid was 0.1 to 0.3 N which was 7 to 21 percent of Japonica types. 15. The detachment force of the lower portion was little bigger than that of the upper portion in a penicle and was not significantly affected by the harvesting period from September 28 to October 20. 16. The tensile and bending detachment forces decreased with decrease of the moisture content from 23 to 13 percent (w.b.) by the natural drying, and the decreasing rate of detachment forces along the moisture content was the greater in the bending detachment force than the tensile detachment force.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.6
• /
• pp.327-340
• /
• 2017

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2016. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of flow, heat and mass transfer, the reduction of pollutant exhaust gas, cooling and heating, the renewable energy system and the flow around buildings. CFD schemes were used more for all research areas. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results of the long-term performance variation of the plate-type enthalpy exchange element made of paper, design optimization of an extruded-type cooling structure for reducing the weight of LED street lights, and hot plate welding of thermoplastic elastomer packing. In the area of pool boiling and condensing, the heat transfer characteristics of a finned-tube heat exchanger in a PCM (phase change material) thermal energy storage system, influence of flow boiling heat transfer on fouling phenomenon in nanofluids, and PCM at the simultaneous charging and discharging condition were studied. In the area of industrial heat exchangers, one-dimensional flow network model and porous-media model, and R245fa in a plate-shell heat exchanger were studied. (3) Various studies were published in the categories of refrigeration cycle, alternative refrigeration/energy system, system control. In the refrigeration cycle category, subjects include mobile cold storage heat exchanger, compressor reliability, indirect refrigeration system with $CO_2$ as secondary fluid, heat pump for fuel-cell vehicle, heat recovery from hybrid drier and heat exchangers with two-port and flat tubes. In the alternative refrigeration/energy system category, subjects include membrane module for dehumidification refrigeration, desiccant-assisted low-temperature drying, regenerative evaporative cooler and ejector-assisted multi-stage evaporation. In the system control category, subjects include multi-refrigeration system control, emergency cooling of data center and variable-speed compressor control. (4) In building mechanical system research fields, fifteenth studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, renewable energies, etc. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which could be help for improving the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the analyses of indoor thermal environments controlled by portable cooler, the effects of outdoor wind pressure in airflow at high-rise buildings, window air tightness related to the filling piece shapes, stack effect in core type's office building and the development of a movable drawer-type light shelf with adjustable depth of the reflector. The subjects of building energy were worked on the energy consumption analysis in office building, the prediction of exit air temperature of horizontal geothermal heat exchanger, LS-SVM based modeling of hot water supply load for district heating system, the energy saving effect of ERV system using night purge control method and the effect of strengthened insulation level to the building heating and cooling load.

• Korean Journal of Food Science and Technology
• /
• v.47 no.1
• /
• pp.95-102
• /
• 2015

The Maillard reaction is a non-enzymatic reaction between amino and carbonyl groups. During milk processing, lactose reacts with milk protein through this reaction. Infant formulas (IFs) are milk-based products processed with heat-treatments, including spray-drying and sterilization. Because IFs contain higher Maillard reaction products (MRPs) than breast milk, formula-fed infants are subject to higher MRP exposure than breast milk-fed ones. In this study, we investigated the optimization of conditions for minimal MRP formation with the addition of $\small{L}$-carnitine ($\small{L}$-car), pyridoxine hydrochloride (PH), and $\small{DL}$-${\alpha}$-tocopheryl acetate (${\alpha}$-T) in an IF model system. MRP formation was monitored by response surface methodology using fluorescence intensity (FI) and 5-hydroxymethylfurfural (HMF) content. The optimal condition for minimizing the formation of MRPs was with $2.3{\mu}M$ $\small{L}$-car, $15.8{\mu}M$ PH, and $20.6{\mu}M$ ${\alpha}$-T. Under this condition, the predicted values were 77.4% FI and 248.7 ppb HMF.