• Journal of the Korea Institute of Building Construction
• /
• v.17 no.2
• /
• pp.127-134
• /
• 2017

In this study, moist curing equipment was used in the exist gang-form system. By achieving sufficient spray curing, the quality of the concrete was improved and the cracking occurred in building's side wall was decreased. The following results could be made as the conclusion. For the compressive strength, all zones showed the similar results. Comparing with the zone without using moist curing equipment, the zone used moist curing equipment showed higher rebound hardness results. For the cracking, the zone utilized moist curing equipment showed the cracking averaged as 6.6 m and the zone without using moist curing equipment showed the cracking averaged as 10.3m. The effectof reducing cracking by utilizing moist curing equipment is about 36 %. Using moist curing equipment is considered as a good solution to reduce the cracking in the structure. Considering all the factors analysed, using moist curing equipment improved the quality of the concrete and decreased the cracking. When this equipment was used in the construction site, it is expected that the construction periodcan be shrunk and the ratio of defect caused by drying shrinkage can be decreased. In this research conditions, The 0.3mm sized moist curing equipment provided the most desirable results on concrete quality and preventing cracking.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.73-78
• /
• 2017

In this paper, the fire risk using a bimetal type thermometer for construction installation is presented. Because construction equipment is used widely in the field and the site is exposed to explosions and fire by combustible gas or fume, strong restrictions on the structure and usage are applied. Moreover, the risk of fire increases as precise temperature measurements are poorly conducted via an inner temperature sensor inside construction furnace. Therefore, this paper presents the results of structural analysis of a bimetal temperature sensor which is used widely in construction installation and temperature measurement experiments relative to the material property of the target object. The results revealed the relatively precise temperature of the liquid object, whereas those of the gas and solid object showed a lower temperature compared to the real temperature. This shows that bimetal-type temperature sensor is more suitable for measuring a liquid state object than measuring a gas or solid state object.

• Journal of the Korean Institute of Gas
• /
• v.19 no.4
• /
• pp.49-54
• /
• 2015

The purpose of this study is to assess the risk of depending on the presence or absence of safety device of domestic heating and drying furnaces, by derivation and analysis of accident frequency of safety devices through FTA (Fault Tree Analysis). Installation standards are lacking in Korean for the safety device of LPG heating and drying furnace, which have a risk of explosion due to structure to trap the leaked gas. Four different safety devices were selected on the basis of NFPA and national standards for combustors of other equipment. Effects of frequency reduction in accidents were analyzed before and after installing the safety devices respectively. As a result, a minimal leakage safety device was presented for preventing damages from gas leak of domestic LPG heating and drying furnace.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.37-45
• /
• 2018

An electric vehicle is an environmentally friendly vehicle because there is no exhaust gas, unlike gasoline automobiles. On the other hand, because the electric vehicle is driven by electric power charged in batteries, the distance to go through a single charge depends on the energy density of the batteries. Therefore, a lithium-ion battery with a high energy density is a good candidate for batteries in electric vehicles. Because the electrode is an essential component that governs the efficiency of a lithium-ion battery, the electrode manufacturing process plays a vital role in the entire production process of lithium-ion batteries. In particular, the drying process during the electrode manufacturing process is a critical process that has a significant influence on the performance. This paper proposes an innovative process for improving the efficiency and productivity of the drying process in electrode manufacturing and describe the equipment design method and development results. In particular, the design procedure and development method for enhancing the electrode adhesion power, atmospheric pressure superheated steam drying technology, and drying furnace slimming technologies are presented. As a result, high-speed drying technology was developed for battery electrodes through the world's first turbo dryer technology for mass production using open/integrated atmospheric pressure superheated steam. Compared to the conventional drying process, the drying furnace improved the productivity (Dry Lead Time $0.7min{\rightarrow}0.5min$).

• Journal of the Korean Ceramic Society
• /
• v.38 no.4
• /
• pp.307-307
• /
• 2001

Combustion process with citrate was used to produce the LiMn$_2$O$_4$powder. Precursors are pre-ignited in open air followed by post-heating in the range from $600^{\circ}C$ to 80$0^{\circ}C$ for 4h. With varying the molar ratio (R) of ethylene glycol (EG) to citric acid (CA) from 0 to 4, the effect of EG content on powder characteristics is evaluated. Vacuum drying promote the auto-ignition at room temperature. With small addition of EG metal ion was selectively segregated with organic substances and undesired lithium evaporation occurred during post-heating. LiMn$_2$O$_4$phase which is produced by combustion reaction was decomposed back to Mn$_3$O$_4$because the reaction temperature was higher than 95$0^{\circ}C$. With increasing EG content, the homogeneity of LiMn$_2$O$_4$powder increased and specific surface area increased. And lithium evaporation during vacuum drying and/or ignition also increased.

• Journal of Welding and Joining
• /
• v.10 no.2
• /
• pp.51-62
• /
• 1992

A torch was designed and fabricated in order to develope the technology of "locally drying underwater welding" by water curtain method. The condition for the formation of the possible local cavity, the mechanical properties and the thermal cycle of welds were investigated in the developed welding equipment compared with in-air welding. The possibility of highly reliable and practical underwater welding was found. The proper local cavity was formed above the water flowrate of 30l/min and CO$_{2}$ gas flowrate of 100l/min. The bead width and penetration depth were increased with increasing welding current. The hardness of weldments is about 160Hv in air welding, but about 210Hv in underwater welding. The elongation and the impact value of underwater weldments are 15% and 6Kg/cm$^{2}$ respectively, which are only half as much as the values of in-air welding. The cooling time in the temperature range from 800.deg.C to 500.deg.C affecting the structure and the hardness of weldments is about 22sec. in air welding while about 10sec. in underwater welding.r welding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1849-1852
• /
• 2005

An automatic cap-washing machine is developed for rinse and dry of synthetic resin cap which is used in spring water bottle. This machine should be achieved all processes washing and drying, array, transfer automatically. A cap is washed by an ozonized water and pure water first. Next, a cap is dried by a hot wind drying equipment. In this paper, structural and modal analysis for the cap-washing machine is carried out to check the design criterion of the machine. The analysis is carried out by FEM simulation using the commercial software, CATIA V5. And a fictitious mass properties was used for the analysis of the machine. Finally, the machine performance is shown to be satisfactory.

• Applied Biological Chemistry
• /
• v.20 no.1
• /
• pp.95-100
• /
• 1977

To get a basic information for improving Korean's pattern of comsuming red pepper and the possibility of its industrial production, consumer's ways of red pepper processing and his present dietary habits were surveyed and the results are follows; (1) Korean's daily consumption of red pepper was on the average 9.2 g on the basis of the whole dried red pepper. (2) The tendency of evading the home drying method was increased; 72.22% in urban community and 50.4% in rural community purchased the dried red pepper in the lump yearly. The household purchasing the fresh red pepper and using the home drying was 27.8% in urban community and 49.6% in rural community, so one third of urban household was still using the home drying method. The case of dependence on tine drying factory was no more than 2.6%. (3) Drying method was mainly sun drying which done on the poor circumstance like as the street side without the proper equipment of drying. Home process of red pepper by housewife was 70.8%, and the old, housekeeper were only 7.3% respectively. (4) The hygienic sense in the drying was rare; 68.8% was not washed and 51.9% of decayed red pepper was eaten. (5) Koreans prefered the strong pungency, deep red color and fine powder form. (6) While the 45.5% of seed was collected by second hand dealer and made use of as resources of edible oil, it was not used effectively due to complexity of its collection system. (7) While 40.1% desired the improvement of red pepper dietary life, 41.1% distrusted the present commercial red pepper powder on the market. From the results above, we conclude the fact many households have still hygienically poor red pepper processed at home, in spite of the red pepper is one of the most important spices in Korea. Considering the growing urban population, reduction of unemployed labor due to the increasing nuclear family and hygienic problems caused by the serious pollution, the improvement of red pepper processing method is urgently required. And it is believed that red pepper has a good prospect to be processed on the industrial scale in Korea.

• Korean Journal of Materials Research
• /
• v.28 no.4
• /
• pp.201-207
• /
• 2018

Infrared(IR) heating has many advantages, such as energy efficiency, reduced heating time, cleanliness, equipment compactness, high drying rate and easy automation. These features of IR heating provide widely industrial applications, such as surface heat treatment in semiconductor fabrication, thermoforming of polymers, drying and disinfection of food products, heating to metal forging, and drying of wet materials. In this study, the characteristics of a protected gold mirror were examined by spectrophotometer and the lifetime of the coating layers were evaluated by a cross-cutting method and salt spray test. The effects of manufacturing conditions on the protected gold mirror were seen and remedies for these effects were noted in order to improve the properties of the protected gold mirror in the drying process. The reflectance and lifetime of the protected gold mirror was influenced by manufacturing conditions, such as surface roughness and forming conditions of the anti-oxide layer, the adhesion layer, the reflecting layer and the protection layer. The results of this study showed that the protected gold mirror manufactured using a buffing method for pre-treatment resulted in the most effective reflectance. In addition, $Al_2O_3$ coating on an Al substrate as an anti-oxide layer was more effective than the anodizing process in the test of reflectance. Furthermore, the protected gold mirror manufactured by layers forming of various materials resulted in the most effective reflectance and lifetime when coated with $Al_2O_3$ as the anti-oxide layer, coated Cr as the adhesion layer, and coated $MgF_2$ as the protection layer.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.146-147
• /
• 2006

In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heat using hot air between sludge particle and heated gas. In this paper, a numerical analysis was performed for the structural analysis of the 3-pass rotary dryer through the finite elemeny method and an experiment was done for the structural stability. And reasonable relation was found between analysis and experiment.