• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.619-624
• /
• 1990

This study deals with the effectiveness and its reaction of stearic acid, ethyl silicate and ethylene glycol as grinding aids in grinding of Hwasun flint clay by dry ball milling process. Results are follows ; 1) It was effective that stearic acid and ethyl silicate act as the grinding aids in grinding of Hwasun flint clay. Also, it was proven that addition of stearic acid and ethyl silicate was the most effective in 1.0 and 0.75wt%, respectively. 2) The addition of ethylene glycol below 0.5wt% showed better result than none, but when added more than 0.5wt% it behaved as the inhibitor of grinding process. 3) It was investigated that grinding aids increased the ability of the particle dispression by reducing the strong chhesive forces which is caused by extensive surface tension of water.

• YAKHAK HOEJI
• /
• v.46 no.2
• /
• pp.102-107
• /
• 2002

The particle size of medicinal materials is an important physical property which affects the pharmaceutical behaviors such as dissolution, chemical stability, compressibility and bioavailability of solid dosage forms. The size reduction of raw pharmaceutical powder is needed to formulize insoluble drugs or slightly soluble drugs and to improve the pharmaceutical properties such as the solubility, the pharmaceutical mixing and the dispersion. The objective of the present study is to evaluate the grinding characteristics of ursodeoxycholic acid(UDCA) as a model of insoluble drugs. The effects of the grinding time and the amount of additive on particle size distribution of ground UDCA were investigated. Grinding of insoluble drug, UDCA and a series of dry co-grinding experiments of UDCA with sodium lauryl sulfate(SLS) as an additive were carried out using a planetary ball mill. It was measured that the median diameter and the particle size distribution of ground products with grinding UDCA and additive SLS by Mastersizer. As a result of co-grinding of UDCA and SLS, the particle size of co-grinding products was decreased more than single grinding one. However, it was observed that co-grinding products were reaggregated to larger particles after 120 min.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.11 no.2
• /
• pp.32-41
• /
• 1991

This paper is to analyze the surface roughness in wet and dry surface grinding in which working conditions are table feed, cross feed and down feed. FFT analyzer is used to identify the surface roughness and the data of surface roughness are stored and displayed using an interfaced computer. In results, components affecting surface roughness exist within 200Hz with respect the conditions and methods of grinding operation. Also, with increase of table feed, cross feed and down feed, the value of surface roughness increases. Of them, cross feed has first influence on surface roughness. In dry, preciser surface can be obtained than one in wet.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.870-874
• /
• 1997

Super-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with resinoid-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance and the surface roughness are measured and discussed. The results are as follows.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.227-234
• /
• 2010

We investigated the effect of dry grinding of laterite on the extraction of nickel and cobalt. The major chemical compositions of the sample for this work were $SiO_2$, $Fe_2O_3$ and MgO. The sample contained 0.81% Ni and 0.02% Co. The major minerals of the sample were lizardite and quartz with minor amounts of forsterite and enstatite. The mean particle size, specific surface area and density of the ground sample decreased with increasing grinding time, while the amorphization of lizardite increased as identified by XRD analysis. The grinding enabled the extraction ratio of Ni and Co to increase by the breakdown of Mg-OH bonding in the lizardite structure. However, physical properties of quartz were not changed by grinding. The extraction ratio of Ni and Co increased with increasing grinding time. Approximately 80% of Ni and Co were extracted regardless of the kind of acid solutions when the sample was ground for 60 minutes.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.11-17
• /
• 2001

• Journal of the Korean Society of Safety
• /
• v.5 no.1
• /
• pp.31-39
• /
• 1990

In this paper, the influence of the table speed, metal removal rate and grinding fluid on long wheel workpiece contact zone at high effect grinding was investigated by theoretical analyses and measuring the temperature, and discussed by the temperature distribution in grinding surface layer. Main results obtained are as follows, 1) Rega.dless of the table speed, the temperature gap of the workpiece(heat influx) is about 6-8 times as high in dry condition as in wet condition. 2) Good grinding condition can be obtained owing to the effect of grinding fluid without any burning defect under the condition of the metal removal rate(1.0mm$^3$/mm.s) in case of wet grinding. 3) When the depth from the surface layer is about 1.25-1.5mm under the condition of the slow table speed, surface temperature goes up higher as the table speed slows down, because long contact time is laked at the surface layer. 4) In case of the same metal removal rate, the lower the table speed becomes, the higher the surface temperature is, because grinding depth has a far more influence on wheel workpiece contact zone than the table speed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.338-346
• /
• 2000

Although the net-shape molding of composites is generally recommended, molded composites are frequently required cutting or grinding due to the dimensional inaccuracy for precision machine elements . During the composite machining operations such as cutting and grinding, the temperature at the cutting point may increase beyond the allowed limit due to the low thermal conductivity of composites, which might degrade the matrix of composite. Therefore, in this work, the temperature at the cutting point during cut-off grinding of carbon fiber epoxy composites was measured. The cutting force and surface roughness were also measured to investigate the cut-off grinding characteristics of the composites. The experiments were performed both under dry and wet grinding conditions with respect to cutting speed and feed rate. From the experimental investigation, the optimal conditions for the composite cut-off grinding were suggested.

• Composites Research
• /
• v.13 no.5
• /
• pp.44-49
• /
• 2000

Although the net-shape molding of composites is generally recommended, molded composites frequently requires cutting or grinding due to the dimensional inaccuracy for precision machine elements. The surface roughness and cutting force were also measured to investigate the surface grinding characteristics of the composites using the vitrified bonded wheel (WA, GC). The experiments were performed dry grinding conditions with respect to cutting speed, feed speed, depth of cut of the stacking sequence $[O]_{nT.}$ From the experimental investigation, the optimal conditions both the vitrified bonded wheel WA and GC for the surface grinding are suggested.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.606-611
• /
• 2007

This study was conducted to beneficiation of magnesite by dry grinding and air classification. The raw ore was ground in a ball mill and pin mill controlled with grinding time and linear velocity of grinding media and fractionated in an air classifier. Pin mill is more efficient than the ball mill for liberation. As a result, the MgO grade of concentrate was 47.1% with recovery of 51.51% for classified with 3,000rpm of air classifier for ground at 13,000rpm in pin mill.