• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.6
• /
• pp.320-328
• /
• 2003

A specimen of Cu-35%Sn alloy has been subjected to the unidirectional heat treatment in an attempt to examine the evolution of microstructures under varying thermal conditions. The specimen was cast in the form of a cylinder 10 mm in diameter and 200 mm in length, which was then installed in the temperature gradient field established inside a vertical tube furnace. The furnace temperature was adjusted to make the upper part at $750^{\circ}C$ and bottom end part at $300^{\circ}C$ of the specimen. The experiment was terminated by dropping it into water after the 30 minutes holding at given temperature. By the rapid cooling, the high temperature phases, ${\gamma}$ and ${\zeta}$, were retained at ambient temperature with some of ${\gamma}$ phase transformed to ${\varepsilon}$ phase, especially at the grain boundaries of ${\gamma}$ phase. The presence of ${\varepsilon}$ phase was found to determine the nature of phase transformations of the ${\zeta}$ phase undergoes upon cooling. In the close area of the ${\varepsilon}$ phase, ${\varepsilon}$ phase grew separately out of ${\zeta}$, and adds to the preexisting ${\varepsilon}$ whereas in areas away from ${\varepsilon}$, both ${\delta}$ and ${\varepsilon}$ grew simultaneously out of ${\zeta}$, and formed a lamella eutectoid structure. The transformation to ${\delta}$ was found to occur only in slow cooling. The hardness on each phase showed that the retained phases, ${\gamma}$ and ${\zeta}$, could be plastically deformed without brittle fracture while the phases, ${\varepsilon}$ and ${\delta}$, were too brittle to be deformed.

• International Journal of Highway Engineering
• /
• v.16 no.3
• /
• pp.119-129
• /
• 2014

PURPOSES : This investigational survey is to observe a proper spatial aggregation method for path travel time estimation using the hi-pass DSRC system. METHODS : The links which connect the nodes of section detectors location are used for path travel time estimation traditionally. It makes some problem such as increasing accumulation errors and processing times. In this background, the new links composition methods for spatial aggregation are considered by using some types of nodes as IC, JC, RSE combination. Path travel times estimated by new aggregation methods are compared with PBM travel times by MAE, MAPE and statistical hypothesis tests. RESULTS : The results of minimum sample size and missing rate for 5 minutes aggregation interval are satisfied except for JC link path travel time in Seoul TG~Kuemho JC. Thus, it was additionally observed for minimum sample size satisfaction. In 15, 30 minutes and 1 hour aggregation intervals, all conditions are satisfied by the minimum sample size criteria. For accuracy test and statistical hypothesis test, it has been proved that RSE, Conzone, IC, JC links have equivalent errors and statistical characteristics. CONCLUSIONS : There are some errors between the PBM and the LBM methods that come from dropping vehicles by rest areas. Consequently, this survey result means each of links compositions are available for the estimation of path travel time when PBM vehicles are missed.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.7
• /
• pp.2653-2657
• /
• 2015

Nasopharyngeal carcinoma (NPC) is the second most common neoplasm of head and neck in Tunisia. The distribution is bimodal with a first period occurrence between 15 and 20 years old and a second peak at around 50 years of age. Undifferentiated carcinoma of nasopharynx type III (UCNT) is the predominant histological type (93.4%). Data of cancer registry of North Tunisia confirmed that it is an intermediate risk area for NPC with overall ASRs of 3.6 and 1.6/100,000 respectively in males and females. This study aimed to present the evolution of incidence rate of nasopharyngeal carcinoma over a period of 12 years (1994-2006). Data of cancer registry of North Tunisia (NTCR), covering half of the Tunisian population, were used to determine evolution of NPC incidence, calculated by 5 year periods. The estimated annual percentage change (EAPC) was used as an estimate of the trend. To best summarize the behavior or the data trend across years, we used a join-point regression program. Between 1994 and 2006, we observed negative annual average change of standardized incidence in men and women (-3.3%and -2.7%) also for the standardized incidences which showed a rather important decline (26.4% in males and 22.3% in females). The truncated age standardized incidence rate of NPC in adults aged of 30 years old and more (N= 1209) decreased by -0.4% per year from 1994 to 2006 over time in north Tunisia dropping from 6.09 to 4.14 person-years. However, the rate was relatively stable during this period among youths aged 0-29 years (N= 233) in both sexes. NPC demonstrated a favorable evolution from 1994-2006 probably due to a improvement in socioeconomic conditions.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.5 no.5
• /
• pp.1049-1068
• /
• 2011

In this paper a simple and effective call admission control (CAC) scheme is proposed for the emerging interleave-division multiple-access (IDMA) systems, supporting a variety of traffic types and offering different quality of service (QoS) requirements and priority levels. The proposed scheme is signal-to-interference-plus-noise ratio (SINR) evolution based CAC (SE-CAC). The key idea behind the scheme is to take advantage of the SINR evolution technique in the process of making admission decisions, which is developed from the effective chip-by-chip (CBC) multi-user detection (MUD) process in IDMA systems. By virtue of this semi-analytical technique, the MUD efficiency can be estimated accurately. Additionally, the computational complexity can be considerably reduced. These features make the scheme highly suitable for IDMA systems, which can combat intra-cell interference efficiently with simple CBC MUD. Analysis and simulation results show that compared to the traditional CAC scheme considering MUD efficiency as a constant, the proposed SE-CAC scheme can guarantee high power efficiency and throughput for multimedia traffic even in heavy load conditions, illustrating the high efficiency of CBC MUD. Furthermore, based on the SINR evolution, the SE-CAC can make accurate estimation of available resource considering the effect of MUD, leading to low outage probability as well as low blocking and dropping probability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.7A
• /
• pp.711-723
• /
• 2002

A finer granular scalable (FGS) version of ISO/IEC MPEG-4 video streaming is investigated in this work with the prioritized stream delivery over loss-rate differentiated networks. Our proposed system is focused on the seamless integration of rate adaptation, prioritized packetization, and simplified differentiation for the MPEG-4 FGS video streaming. The proposed system consists of three key components: 1) rate adaptation with scalable source encoding, 2) content-aware prioritized packetization, and 3) loss-based differential forwarding. More specifically, a constant-quality rate adaptation is first achieved by optimally truncating the over-coded FGS stream based on the embedding rate-distortion (R-D) information (obtained from a piecewise linear R-D model). The rate-controlled video stream is then packetized and prioritized according to the loss impact of each packet. Prioritized packets are transmitted over the underlying network, where packets are subject to differentiated dropping and forwarding. By focusing on the end-to-end quality, we establish an effective working conditions for the proposed video streaming and the superior performance is verified by simulated MPEG-4 FGS video streaming.

• Journal of the Korea Institute of Building Construction
• /
• v.4 no.1
• /
• pp.97-103
• /
• 2004

In case of a fire in road or railway tunnel it is always necessary to keep the escape condition as good as possible. Most of the victims of major fires in tunnels are because they couldn't leave the tunnel in time and were trapped by smoke, or rescue teams couldn't reach the place of the accident due to low visibility and high temperature. In spring 2003 a comprehensive field experiment was undertaken in a large scaled tunnel in Youngin City to test the effectiveness of a new water spray curtain system, designed to the air qualify inside of a tunnel in case of fire during passenger's escape to safe routes, In order to control the smoke propagation, fixed water sprayed nozzles were used to make water curtain system, which can be installed or hanging water piping line below ceiling. The experiment was accompanied by an extensive measurement campaign in order to measure temperature dropping effect and flow conditions as well as CO concentration for various water sprayed curtains produced by sprinkler heads or water spray nozzle. Eventually comparison analysis were undertaken to investigate the performance of water curtains under fixed water pressure. Therefore most effective water curtain system was presented on the basis of water droplet size in long tunnel.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.1
• /
• pp.33-39
• /
• 2022

As 3D printer-related patents expire and major technologies are disclosed, the price of 3D printers is dropping, creating an environment where you can easily find the product you want. In particular, the cheapest FDM (Fused Deposition Modeling) 3D printer is being used in various fields. The FDM method can be manufactured without collapsing of the shape only by attaching a support under certain conditions when outputting the shape. When printing a shape without a support, the irregular surface that occurs at a certain angle is a defect in the product, but it is considered that it can be used as another fun factor in terms of arts and crafts. In this paper, to obtain such an irregular surface, factors that can affect the output were controlled and only the output angle was tested as a displacement factor. As a result of the experiment, it was possible to obtain an irregular surface without the filament flowing down when printing at an angle of 62° to 70° from the vertical. Also, artificially irregular surfaces were applied to craft products.

• Resources Recycling
• /
• v.32 no.2
• /
• pp.33-42
• /
• 2023

Metal emulsions have been studied for several decades as a method of increasing the efficiency of the steelmaking process. This study was performed using a water model, observable at room temperature, to compensate for the disadvantages of the high-temperature experiment, the results of which are difficult to observe visually. As a substitute for metal-in-slag emulsions, experiments were conducted by dropping distilled water into silicone oil and comparing the results with the results of a calculation by momentum balance equations. The descending velocity of the water droplet decreased as the diameter of the droplet and viscosity of the fluid (silicon oil) increased. To simulate the descending velocity of a water droplet in silicon oil under stirring conditions, the flow rate of the fluid (silicon oil) was measured by particle image velocimetry (PIV) methods. The calculation of the descending velocity of the water droplet was in good agreement with the measured values, with and without stirring a viscous silicone oil.

• Journal of Aerospace System Engineering
• /
• v.17 no.2
• /
• pp.86-93
• /
• 2023

Pyrotechnic separation devices have been widely used as holding and release mechanism for deployable appendage. However, pyro-shock can cause temporal or permanent damage on shock sensitive components such as electronics, mechanism, and brittle components. This study proposed a low-stiffness blade based passive shock absorber using a multi-layered stiffener laminated with viscoelastic acrylic tapes for reducing transmitted pyro-shock upon explosion of pyrotechnic separation devices. The multi-layered structure with viscoelastic tape has high-damping characteristics to effectively secure structural integrity of low-stiffness blades under the launch environment. The design effectiveness was verified through a shock test by dropping a pendulum. The structural integrity of the shock absorber under a launch environment was evaluated through structural analysis under load conditions with a deployable payload.

• Journal of Sensor Science and Technology
• /
• v.33 no.1
• /
• pp.24-29
• /
• 2024

Inkjet printing technology is used to mass-produce displays and electrochemical sensors by dropping tens of pico-liters or less of specific-purpose ink through nozzles, just as ink is sprayed and printed on paper. Unlike the deposition method for vaporizing material in a vacuum, inkjet printing technology can be used for processing even under general atmospheric pressure and has a cost advantage because the material is dissolved in a solvent and used in the form of ink. In addition, because it can only be printed on the desired part, masks are not required. However, a technical shortcoming is the difficulty for commercialization, such as uniformity for forming the thickness and coffee ring effect. As sizes of devices decrease, the need to print electrodes with precision, thinness, and uniformity increases. In this study, we improved the printing and processing conditions to form a homogeneous electrode using Ag ink (DGP-45LT-15C) and applied this for patterning to fabricate a heat sensor. Upon the application of voltage to the heat sensor, the model with an extended width exhibited superior heat performance. However, in terms of sheet resistance, the model yielded an equivalent value of 21.6 Ω/□ compared to the ITO.