• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.E2
• /
• pp.78-88
• /
• 2006

In order to study the characteristics of cloud, a real-scale experiment for cloud generation was carried out using an extinct vertical mine (430 m height) located in the northeastern Honshu, Japan. The dry particles generated from the three-step concentrations of NaCl solutions were used for cloud generation. The number size distributions of initial dry particles and cloud droplets were monitored by Scanning Mobility Particle Sizer (SMPS) and Forward Scattering Spectrometer Probe (FSSP) at bottom and upper sites of pit, respectively. The polymeric water absorbent film (PWAF) method was employed to measure liquid water content ($W_L$) as a function of droplet size. Moreover the chemical properties of individual droplet replicas were determined by micro-PIXE. The CCN number concentration shows the lognormal form in dependence of the particle size, while the number size distributions of droplets are bimodal showing the peaks around $9{\mu}m$ and $20{\mu}m$ for every case. In comparison to background mineral particles, right shifting of size distribution line for NaCl particles was occurred. When NaCl solutions with three-step different concentrations were neulized, $W_L$ shows the strong droplet size dependence. It varied from $10.0mg\;m^{-3}$ up to $13.6mg\;m^{-3}$ with average $11.6mg\;m^{-3}$. A good relationship between $W_L$ and cloud droplet number concentration was obtained. Both chemical inhomogeneities (mixed components with mineral and C1) and homogeneities (only mineral components or C1) in individual droplet replicas were obviously observed from micro-PIXE elemental images.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.51-56
• /
• 2013

This paper describes the atomization characteristics, as well as the velocity and size distribution, of DME spray based on common-rail injection system. To analyze the possibility of using DME fuel as an alternative fuel of diesel, spray atomization characteristics were investigated. For this investigation, two-dimensional phase Doppler analyzer system was used to obtain droplet size and velocity distribution simultaneously. Velocity and droplet size measurements were performed at various injection pressures. Results showed that increasing pressure from 25MPa to 50MPa leads to higher spray droplet velocities and smaller droplet diameter but injection pressure above 40MPa, no signifiant reduction was observed. With the droplet velocity and SMD comparison between diesel and DME fuel, it can be observed that DME has smaller SMD and droplet velocity due to its low surface tension.

• Journal of ILASS-Korea
• /
• v.20 no.3
• /
• pp.175-180
• /
• 2015

A series of sprinkler discharging tests was conducted to measure the droplet size and its distribution of residential fire sprinkler heads. Droplet sizes in sprinkler spray were measured using a laser diffraction method for the flush, circular and pendent type sprinkler head. In this study, the $D_{v,50}$ of the flush type sprinkler heads were ranged between $530{\sim}1040{\mu}m$ and those of circular and pendent type were $988{\mu}m$ and $916{\mu}m$, respectively. The measured cumulative volume distributions were followed by a combination of the log-normal and Rosin-Rammler distribution which is widely used in the computational fire analysis and the parameters of distribution function were obtained from the best fit line through the measured data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.167-174
• /
• 1997

The penetration depth and the size distribution of the droplets of fuel sprays are important in the operation of spark-ignition MPI engines. A fluorescence/scattering image technique for droplet sizing was applied to measure th edroplet size distribution in non-evaporating gasoline sprays. The fluorescence and scattering lights were imaged simultaneously by the two-dimensional visualization system composed of a laser sheet, a doubling prism, optical filters, and a CCD camera. Quantitative droplet size distributions were extracted from evaluating the ratio of the two light densities. The mean droplet size measured by the fluorescence/scattering technique was compared with the result obtained by the enlarged photographs of droplets. The fluorescence/scattering image technique also gives the useful information of the characteristics of droplet impingement in a inclined wall.

• Journal of Power System Engineering
• /
• v.2 no.1
• /
• pp.25-30
• /
• 1998

In order to investigate the droplet size distribution and Sauter Mean Diameter in a ultra high pressure diesel spray, fuel was injected with ultra high pressure into the environments of high pressure and room temperature by an Electronic Hydraulic Fuel Injection System. Droplet size was measured with the immersion liquid sampling technique. The immersion liquid was used a mixture of water-methycellulose solution and ethanol. The Sauter Mean Diameter decreased with increasing injection pressure, with a decrease environmental pressure (back pressure) and nozzle diameter. Increasing the injection pressure makes the fuel density distribution of the spray more homogeneous. An empirical correlation was developed among injection pressure, air density, nozzle diameter and the Sauter Mean Diameter of spray droplets.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.566-574
• /
• 1988

A study is described for obtaining real time in situ size and velocity measurements of the spray-droplet using crossed-beam interferometry. The optical arrangement is similar to dual-beam laser Doppler velocimetry(LDV). Droplets passing trough the probe volume scatter light to the collecting lens placed at 90.deg. off-axis angle. The dual-beam light scatter is analyzed by the geometric optics theory to relate the scattered fringe pattern to droplet diameter. The droplet size measurement is based upon the signal visibility. As the system is based on the Doppler effect, a single component of velocity is velocity is extracted concurrent with the size information. The validity of the method is evaluated by comparing its performance to widely accepted but limited technique, the collection method. By using 90.deg. off-axis scatter detection angle, the measurement of the droplet size and velocity distributions, and the local correlations between droplet sizes and velocities in relatively dense spray environments are made possible.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.633-638
• /
• 2006

Silica powders with spherical shape and narrow size distribution were prepared by large-scale ultrasonic spray pyrolysis applying the droplet classification apparatus. On the other hand, silica powders prepared by large-scale ultrasonic spray pyrolysis without droplet classification apparatus had broad size distribution. Droplet classification apparatus used in this paper applied the principles of cyclone and dispersion plate with small holes. The droplets formed from the ultrasonic spray generator applying the droplet classification apparatus had narrow size distribution. The droplets with fine and large sizes were eliminated by droplet classification apparatus. The optimum flow rate of the carrier gas and diameter of the hole of the dispersion plate were studied to reduce the size distribution of the silica powders prepared by large-scale ultrasonic spray pyrolysis. The size distribution of the silica powders prepared by large-scale ultrasonic spray pyrolysis at the optimum preparation conditions was 0.76.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.23-30
• /
• 2006

Effects of liquid-crystal droplets size on electro-optical properties of the polymer dispersed liquid crystals are investigated experimentally The liquid crystal droplets size was varied by controlling the Laser power for phase separation and LC/oligomer composition ratio. Electro-optical switching voltage is dependent on the LC/oligomer composition ratio and liquid crystal droplet size. The experimental results showed droplet size will be small and saturation voltage is increased but rise time will be short at high power illumination laser light for phase separation.

• Journal of Integrative Natural Science
• /
• v.17 no.3
• /
• pp.87-92
• /
• 2024

Using the design of experiments (DOE), factors affecting the droplet size of ethyl cellulose (EC) nanoparticles in the manufacturing process were analyzed to optimize process conditions. The concentration of EC dissolved in solvent (acetone or ethanol), the mixing ratio of the EC solution to distilled water, and sonication power were selected as the main variables affecting the droplet size of the nanoparticles. The effect of these variables on droplet size was examined through the signal-to-noise (S/N) ratios of the Taguchi method and ANOVA analysis. Sonication power in the acetone solvent and EC solution concentration in the ethanol solvent were identified as the most influential factors on nanoparticle size.

• Journal of ILASS-Korea
• /
• v.25 no.2
• /
• pp.60-67
• /
• 2020

Despite its benefit in engine thermal efficiency, gasoline-direct-injection (GDI) engines generate substantial particulate matter (PM) emissions compared to conventional port-fuel-injection (PFI) engines. One of the reasons for this is that the spray collapse caused by the spray-to-spray interaction forms the locally rich fuel-air mixture and increases the fuel wall film. Previous studies have investigated the spray collapse phenomenon through the macroscopic observation of spray behavior using laser optical techniques, but it is somewhat difficult to understand the interaction between sprays that is initiated in the near-nozzle region within 10 mm from the nozzle exit. In this study, the spray structure, droplet size and velocity data were obtained using an X-ray imaging technique from the near-nozzle to the downstream of the spray to investigate the spray-to-spray interaction and discuss the effects of spray collapse on local droplet size and velocity distribution. It was found that as the ambient density increases, the spray collapse was promoted due to the intensified spray-to-spray interaction, thereby increasing the local droplet size and velocity from the near-nozzle region as a result of droplet collision/coalescence.