• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.761-769
• /
• 2007

The configuration of the flow channel on a bipolar plate of a proton exchange membrane fuel cell(PEMFC) for efficient reactant supply has great influence on the performance of the fuel cell. Recent demand for higher energy density fuel cells requires an increase in current density at mid voltage range and a decrease in concentration overvoltage at high current density. Therefore, an interdigitated flow channel where mass transfer rate by convection through a gas diffusion layer is greater than the mass transfer by a diffusion mechanism through a gas diffusion layer was recently proposed. This study attempts to analyze the i-V performance, mass transfer and pressure drop in interdigitated flow channels by developing a fully three dimensional simulation model for PEMFC that can deal with anode and cathode flow together. The results indicate that the trade off between performance and pressure loss should be considered for efficient design of flow channels. Although the performance of the fuel cell with interdigitated flow is better than that with conventional flow channels due to a strong mass transfer rate by convection across a gas diffusion layer, there is also an increase in friction due to the strong convection through the porous diffusion layer accompanied by a larger pressure drop along the flow channel. It was evident that the proper selection of the ratio of channel and rib width under counter flow conditions in the fuel cell with interdigitated flow are necessary to optimize the interdigitated flow field design.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.2
• /
• pp.16-23
• /
• 2014

This paper presents a renewable energy configuration plan of Micro grid in Gapa Island. To analyze the characteristics of Micro grid, BESS (Battery Energy Storage System), PMSG (Permanent Magnet Synchronous Generator) and SCIG (Squirrel Cage Induction Generator) are first modelled. The PMSG and SCIG will operate with basis on the real power curve. when the total power demand is larger than the total power generation, the BESS will be operated and the SOC (State Of Charge) is reduced. If the value of SOC could drop down to limited value, the system may be broken because of the voltage drop of BESS. To solve this problem, a DG (Diesel Generator) is used to charge the BESS and keep the voltage value of BESS with in a allowance limit. This paper represents simulation result when PMSG, SCIG connected to the Micro grid installed in Gapa Island. The simulation is carry out by using PSCAD/EMTDC program with actual line constant and transformer parameter in Gapa Island.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.154-154
• /
• 2006

Samsung Electro Mechanics ink jet has developed ultra high resolution alignment system. The alignment system has been developed for repeatable printing of conductive ink. The resolution of alignment system is 0.5um and the velocity of printing working plate is 1.5m/s. So far repeated printing results included sintering process have over 30um of drop mislocation data. In order to improve line thickness and conductivity of metal line, we need to develop the higher mechanical accurate align system. On the demand, this developed align system has under $1{\sim}2{\mu}m$ mispositioning performance and can measure of mechanical accuracy of inkjet printer, as well as the straightness of jetted drop from inkjet head. There is no kinds limit of substrate and ink to use SEM alignment system. By using this alignment system, we progress two experiment of reiterate printing drop and making conductive line on the glass and photo paper. Optical microscope and 3D profiler has been used for measurement of printed ink.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.12
• /
• pp.90-95
• /
• 2009

The application of a large power transformer into a power distribution system was inevitable due to the increase of power demand and distributed generation. However, the decrease of the power transformer‘s impedance causes the short-circuit current of the power distribution system to increase and thus, the higher short-circuit current exceeds the cut-off ratings of the protective devices such as a circuit breaker. To solve these problems, several countermeasures have been proposed to protect the power system effectively from the higher fault current and the superconducting fault current limiter (SFCL) has been expected to be the promising countermeasure. However, the current limiting effect of SFCL including its bus voltage drop compensation depends on SFCL's application location in a distributed power system. In this paper, the current limiting and the bus-voltage drop compensating characteristics of the SFCL applied into a power distribution system were studied. In addition, the quench and the recovery characteristics of the SFCLs in each location of the power distribution system were compared each other.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.1
• /
• pp.49-58
• /
• 2014

Variability factors of transship cargo in the container transportation market analysis short term factors. In the past, studies on the factor of variability in container cargo volume have focused on long term volume forecast and increase in investment and competitiveness from strategic perspectives. Unlike previous studies, this paper analyzes factors of variability in transshipment volume rapidly varying in short term and seeks measures. Since it was identified that transshipment volume depends on vessel operation cost and port volume in long term but effectively on special strategies launched by port authorities in short term, the port authority experienced rapid drop in volume should continue to observe strategies of competition ports and to make use of strategies seeking appropriate countermeasures.

• Journal of Institute of Convergence Technology
• /
• v.1 no.1
• /
• pp.41-47
• /
• 2011

With the world-wide demand on the emission minimization, the needs on the diesel aftertreatment devices with high efficiency are also increasing. In order to effectively develop or design a high-performance diesel particulate filter, a clear understanding on the deposition and regeneration mechanism is required. In the present study, a theory on the lumped parameter model for wall-flow type diesel particulate filters is described focusing on the deposition efficiency, pressure drop inside the filter. The fourth order explicit Runge-Kutta method is utilized for the mass flow rate computation. Engine operation modes with controlled and uncontrolled regeneration options are selected. The computational lumped parameter model is validated by comparing the computed results with the measured data.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.5
• /
• pp.73-85
• /
• 1997

In a drop-on-demand thermal ink-jet printer, the dot size of an ink droplet expelled from a printer depends on the absorption of the paper. This causes severe differences between output images on the different paper materials. In this paper, the color matching algorithm for different papers is proposed. To achieve corresponding color reproduction, dot gain compensatio nbased on saturation was applied to predict color reproduction on a printer. If the dot gain of pigment increases, the white portion of paper decreases while the saturation value increases monotonically. As the results of dot gain compensation, intensity change may appear. Therefore, an intensity compensation without any hue variation is followed to match the colors of different subtrates.

• ETRI Journal
• /
• v.31 no.2
• /
• pp.173-181
• /
• 2009

The growth of the World Wide Web and web-based applications is creating demand for high performance web servers to offer better throughput and shorter user-perceived latency. This demand leads to widely used cluster-based web servers in the Internet infrastructure. Load balancing algorithms play an important role in boosting the performance of cluster web servers. Previous load balancing algorithms suffer a significant performance drop under dynamic and database-driven workloads. We propose an estimation-based load balancing algorithm with admission control for cluster-based web servers. Because it is difficult to accurately determine the load of web servers, we propose an approximate policy. The algorithm classifies requests based on their service times and tracks the number of outstanding requests from each class in each web server node to dynamically estimate each web server load state. The available capacity of each web server is then computed and used for the load balancing and admission control decisions. The implementation results confirm that the proposed scheme improves both the mean response time and the throughput of clusters compared to rival load balancing algorithms and prevents clusters being overloaded even when request rates are beyond the cluster capacity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.673-675
• /
• 2005

Ink jet printheads are now widely used in manufacturing processes that require precise dispensing of materials. Today, Dimatix manufactures a variety of drop-on-demand ink jet printheads for the industrial printing market, but emerging opportunities present fresh challenges to our technology. In response to requirements for digitally printing on flexible substrates and dispensing novel electronic fluids, we are developing next generation jetting technology based on our three-dimensional silicon MEMS technology with a piezo-driven pumping chamber integrated into the chip structure. This presentation will address the functional and physical design features and properties of Dimatix's MEMS process, its characteristics, reliability and usability. Examples of opportunities and applications for digitally printing electronic fluids on flexible substrates with MEMS-based ink jet technology will be presented.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.1
• /
• pp.1-6
• /
• 2016

Recently, proportion of the induction motor load is gradually increased. When a contingency in the power systems, it has been discovered phenomenon that the voltage is delayed recover caused mechanical characteristics of the induction motor load. It can be a serious impact on the voltage stability of the power system considering induction motor load. The scheme to mitigate this phenomenon tripping off the motors to prevent voltage drop and delayed voltage recovery on the load demand side. Fault induced delayed voltage recovery phenomenon is caused by stalling of small induction motor load in transmission level contingencies. In this paper, fault induced delayed voltage recovery phenomenon mitigation method implementation under voltage load shedding on the korean power system considering induction motor load.