• 설비공학논문집
• /
• 제14권2호
• /
• pp.116-126
• /
• 2002

A three dimensional numerical analysis of the corrugated louver fin for a vehicle heat exchanger was performed. The heat transfer rate and the air pressure drop of the corrugated louver fins for a slim heater were compared with experimental results at the same operating conditions. As for the slim heater fin, we found an optimum fin pitch at certain operating conditions. As the fin pitch increased, the air pressure drop decreased. The vertical or flat top fin was superior to the common declined fin in the aspect of heat transfer performance. As the louver length increased, both the heat transfer rate and the air pressure drop increased.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.16-21
• /
• 2016

This study is a numerical analysis of the flow characteristic of a quick coupler. The quick coupler is a popular coupling tool for pipelines in hydraulic and pneumatic systems. In this study, the flow characteristic of a quick coupler outlet is conducted about the flow coefficient. The quick coupler is analyzed for improving flow and confirmed with the study results. The velocities with pressure distribution according to inlet and outlet pressure drop of the coupler are also compared. The flow coefficient is analyzed according to the flow analysis result for each pressure drop. When the pressure drop is 1 psi, the flow coefficient (Cv) matched about 98% of the value provided by the actual product.

• 방사성폐기물학회지
• /
• 제21권2호
• /
• pp.247-253
• /
• 2023

According to NSSC Notice No. 2021-10, safety analysis needs to be introduced in the decommissioning plan. Public and occupational dose analyses should be conducted, specifically for unexpected radiological accidents. Herein, based on the risk matrix and analytic hierarchy process, the method of selecting accident scenarios during the decommissioning of nuclear power plants has been proposed. During decommissioning, the generated spent resin exhibits relatively higher activity than other generated wastes. When accidents occur, the release fraction varies depending on the conditioning method of radioactive waste and type of radioactive nuclides or accidents. Occupational dose analyses for 2 (fire and drop) among 11 accident scenarios have been performed. The radiation doses of the additional exposures caused by the fire and drop accidents are 1.67 and 4.77 mSv, respectively.

• Journal of Biosystems Engineering
• /
• 제26권5호
• /
• pp.461-468
• /
• 2001

Impact between fruits and other materials is a major cause of product damage in harvesting and handling systems. The oriental pears are more susceptible to bruising than other fruits such as European pears and apples, and are required more careful handling. The interest in the handling of the pears for the processing systems has raised the question of the allowable drop height to which pears can be dropped without causing objectionable damage. Drop tests on pears were conducted using an impact device developed by authors to estimate the allowable drop height without bruising. The impact device was constructed to hold in a selected orientation and to release a fruit by vacuum for dropping on to a force transducer. The drop height was adjustable for zero to 60 cm to achieve the desired distance between the bottom of the fruits and the top of the impact force transducer. The transducer was secured to 150 kg$\sub$f/ concrete block. The transducer signal was sampled every 0.17 ms with a strain gage measurement board in the micro computer where it was digitaly stored for later analysis. The selected sample fruit was Niitaka cultivar of pears which is one of the most promising fruit for export in Korea. The pears were harvested during the 1998 harvest season from an orchard in Daejeon. The sample fruit was selected from two groups which were stored for 3 months and 5 months respectively by the method of current commercial practice. The pears were allowed to stabilize at environmental condition(18$^{\circ}C$, 65% rh) of the experimental room. One hundred fifty six pears were tested from the heights of 5, 7.5. 10 and 12.5 cm while measurement were made of impact peak force, contact time, time to peak force, dwell time, pear diameter and mass. The bioyield strength and modulus of elasticity were measured using UTM immediately after each drop test. The allowable drop height was estimated on the base of bioyield strength of the pears in two ways. One was assumed the peak force during impact test increasing linearly with time, and the other was based on the actual drop test results. The computer program was developed for measuring the impact characteristics of the pears and analyzing the data obtained in the study. The peak force increased while contact times decreased with increasing drop height and contact times of the sample from the hard tissue group. The allowable drop height increased with increasing bioyield strength and contact times, and also varied with Poisson\`s ratio, mass and equilibrium radius of the pears. The allowable drop height calculated by a theoretical method was in the range from 1 to 4 cm, meanwhile, the estimated drop height considering the result of the impact test was in the range from 1 to 6 cm. Since the physical properties of fruits affected significantly the allowable drop height, the physical properties of the fruits should be considered when estimating the allowable drop height.

• 한국전산유체공학회지
• /
• 제9권2호
• /
• pp.18-22
• /
• 2004

Numerical investigation has been conducted to figure out flow behavior and pressure drop characteristics of spirally corrugated steel pipe which is widely used in civil, industrial and agricultural field owing to many advantages such as good corrosion resistance and durability, strength, easy and quick installation. Also the poly-ethylene coating spirally corrugated steel pipe has the long life under condition of sea water immerged. In the present study, flow behavior in the spirally corrugated pipe and influence of P/d/sub h/(ratio of wave pitch to hydraulic diameter) to pressure drop are investigated by CFD with various Reynolds number. And also friction factor is estimated by pressure drop obtained by flow analysis. According to computation results, the flow runs spirally up and down along the spiral corrugation in the vicinity of wall, but the effect of spiral corrugation disappears in core region of pipe. As P/d/sub h/ becomes small, more pressure drop occurs in spirally corrugated Pipe. Besides, friction factor augmentation becomes much larger as Re increases. In case of p/d/sub h/=0.38, Pressure drop and friction factor of spirally corrugated pipe are about four times larger than smooth pipe at Re: 1.46×10/sup 6/.

• 대한기계학회논문집B
• /
• 제27권6호
• /
• pp.781-788
• /
• 2003

In the present study, the heat and flow characteristics of a parallel-flow heat exchanger are numerically analyzed by using three-dimensional turbulent modeling. Heat transfer rate and pressure drop are evaluated using the concept of the efficiency index by varying the locations, the shapes and angles of inlet/outlet, and the protrusion height of flat tube. It is found that negative angle of the inlet improves the heat transfer rate and pressure drop. Results show that the locations of the inlet and outlet should be toward the right side and the left side to the reference model, respectively, in order to enhance the heat transfer rate and pressure drop. Increasing the height of the lower header causes pressure drop to decrease and yields the good flow characteristics. The lower protrusion height of flat tube shows the improvement of the heat transfer rate and pressure drop. The heat transfer rate is greatly affected by the parameters of outlet side such as the location and angle of the outlet. However, the pressure drop is influenced by the parameters of inlet side such as the location and angle of inlet and the height of the header.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.250-255
• /
• 2008

This study utilized a high speed lap-shear test to evaluate the mechanical behavior of Sn-37Pb/Cu and Sn-37Pb/Electroless Nickel immersion Gold under bump metallization solder joints under high speed loading and hence the drop reliability. The samples were aged for 120 h at different temperatures ($120^{\circ}C,\;150^{\circ}C,\;170^{\circ}C$) and afterward tested at different displacement rates (0.01 mm/s to 500 mm/s) to examine the effects of aging on the drop life reliability. The combination of the stress-strain graphs captured from the shear tests and identifying a fracture mode dominant in the samples for different strain rates leads us to conclude that the drop reliability of solder joints degrades as the aging temperature increases, possibly due to the role of the IMC layer. This study successfully demonstrates that the analysis based on a high speed lap-shear test could be critically used to evaluate the drop reliability of solder joints.

• 산업진흥연구
• /
• 제8권2호
• /
• pp.81-91
• /
• 2023

본 연구는 고등학생을 대상으로 학업스트레스가 자아존중감, 또래관계 및 그릿을 통하여 학업중단의도에 미치는 메카니즘을 파악하여 학업중단 예방을 위한 기초자료를 제시하는데 있다. 연구대상은 충남의 3개 시군에서 편의표집한 고등학생 283명이었다. 자료분석은 SPSS PC+ Win. ver. 25.0과 SPSS PROCESS macro ver. 4.2를 활용하였으며, 적용된 통계기법은 기술통계, 신뢰도분석, 상관분석 및 조절된 매개효과분석이었다. 연구결과 첫째, 학업스트레스는 학업중단의도와 정적인 상관관계를 보였으나 자아존중감, 그릿, 또래관계와는 부적인 상관관계를 보였다. 둘째, 그릿은 자 아존중감이 또래관계에 미치는 영향을 증진시키는 상승역할 뿐만 아니라 학업스트레스→자아존중감→또래관계→학업중단의도의 경로를 조절 매개하는 역할을 하였다. 고등학생들의 학업스트레스가 학업중단의도에 직접적인 영향을 미치는데, 자아존중감, 또래관계 및 그릿이 학업중단의도를 예방할 수 있는 중요한 변수로 활용될 수 있음을 확인하였다.

• 방사성폐기물학회지
• /
• 제7권1호
• /
• pp.9-16
• /
• 2009

방사성물질 운반용기는 가상 사고조건에서 구조적 건전성이 유지됨을 실험 및 수치해석을 통해 입증하여야 한다. 가상 사고조건에 포함되는 파열낙하 조건에 대한 기존 유한요소해석의 경우 충격완충체에서 재료의 파손이 발생하기 때문에 일반적으로 유한요소모델에서 이 부분을 무시하고 해석한다. 본 논문에서는 파열낙하 해석에서 충격완충체의 변형으로 인한 낙하에너지 흡수의 효과를 고려하기 위해 요소의 적분점에서 응력 이나 변형율이 재료의 파손 기준치에 도달하면 그 요소를 제거하는 방법을 제안한다. 본 해석방법의 효용성을 보이기 위해 한국원자력연구원에서 설계중인 핫셀 운반용기에 대해 파열낙하 해석을 수행하였으며, 요소제거 기법의 적용을 통해 낙하 에너지의 80% 정도가 충격완충체에서 흡수되는 것으로 계산되었다. 본 해석방법은 시험조건에 비해 보수성을 가지는 평가방법이며, 기존의 해석방법과 비교해 파열낙하 조건을 보다 근사적으로 해석할 수 있는 방법이다.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.233-239
• /
• 2017

소듐냉각고속로의 제어집합체는 내부덕트 및 제어봉을 갖는 제어봉집합체를 포함하고 있다. 제어봉집합체는 비상시 긴급 정지를 위하여 중력에 의하여 제어집합체 덕트내에서 낙하한다. 제어봉집합체의 낙하 시간과 충격 속도는 반응삽입시간 및 구조건전성에 관하여 중요한 변수이다. 본 연구의 목적은 낙하 충격에 의한 제어봉집합체의 동적거동 및 건전성평가를 조사하는 것이다. 제어봉집합체의 정상/비정상 낙하조건에서의 충격 해석은 상용 유한요소코드인 LS-DYNA를 사용하여 수행하였다. 낙하 충격 해석 결과, 제어봉집합체는 구조건전성을 유지하고 있으며, 비정상 조건에서도 댐퍼의 유동홀에 정상 삽입 되었다.