• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.561-568
• /
• 2021

In this study, in order to observe the change in the amount of Tire and Road Wear Particles and the ratio of tire components in it according to the tire wear resistance performance, carried out the evaluation by varying the vulcanization reaction design of the tire tread rubber. In addition, in order to improve the reliability of the evaluation of Tire and Road Wear Particles, the evaluation was performed indoor laboratory test equipment that simulates the condition on real driving to exclude various environmental influences including minerals, driver's habits, road surface, weather, tire structure and pattern designs. After the evaluation in closed space, it is estimated that the amount of collected Tire and Road Wear Particles is 84% compared to 100% of the tire and road wear loss weight, of which 96.4~97.7% was around the road and 2.3~3.6% was in the air. As a result of analy sis of the collected Tire and Road Wear particles, the tire component existed 63~75% in the Tire and Road Wear Particles depending on the wear resistance performance of the tire.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.6
• /
• pp.15-26
• /
• 2006

Although numerous investigations have been performed over the years to predict the behavior and bearing capacity of piles, the mechanisms are not yet entirely understood. The prediction of bearing capacity is a difficult task, because large numbers of factors affect the capacity and also have complex relationship one another. Therefore, it is extremely difficult to search the essential factors among many factors, which are related with ground condition, pile type, driving condition and others, and then appropriately consider complicated relationship among the searched factors. The present paper describes the application of Artificial Neural Network (ANN) in predicting the capacity including its components at the tip and along the shaft from dynamic load test of the driven piles. Firstly, the effect of each factor on the value of bearing capacity is investigated on the basis of sensitivity analysis using ANN modeling. Secondly, the authors use the design methodology composed of ANN and genetic algorithm (GA) to find optimal neural network model to predict the bearing capacity. The authors allow this methodology to find the appropriate combination of input parameters, the number of hidden units and the transfer structure among the input, the hidden and the out layers. The results of this study indicate that the neural network model serves as a reliable and simple predictive tool for the bearing capacity of driven piles.

• International Area Studies Review
• /
• v.13 no.1
• /
• pp.391-416
• /
• 2009

The purpose of this paper is to provide an ideal agreement proposal for the satisfactory settlement of FTA origin criteria negotiations, which will be the most severe issue in both inter-governmental FTA negotiations to begin in the near future. Towards this end, we, the authors, based on our nine FTA related agreements already concluded with other countries, researched the concrete origin criteria in the previous origin agreements, analyzed the characteristics of these agreements, and derived the ideal origin rule. As a result, we came to the conclusion that in consideration of Korea and China's FTA's substantial transformation test, it's better to choose any one criterion from the following. Criterion 1: CTH (Change of Heading) and Criterion 2: Value Added Criteria by 40% within region. In addition, we also did that in calculating the ratio of value added, the calculation method and price criteria should be more simple and standardized. It led to the conclusion that the objective deduction method should be used mainly and that CIF or FOB should be used as the price criterion.

• Archives of Plastic Surgery
• /
• v.51 no.2
• /
• pp.251-257
• /
• 2024

Background Plastic surgery has developed to benefit in a variety of challenging areas formerly handled by other disciplines. Medical students do not have a clear picture of plastic surgery as a career due to lacking scope, clinical practice, and understanding of plastic surgery as a clinical area of expertise, including general practitioners, nursing staff, medical trainees, and the general public, and misconceptions about the extent of reconstructive and plastic surgery. Methods A cross-sectional observational study was conducted on Kuwait University Medical students (2nd-7th Years) over a period of 1 month. A questionnaire and a consent form were provided to eligible students. The inclusion criteria were Kuwait University Medical students from 2nd to 7th Years with signed consent form. The response was collected via email sent in coordination with the Vice Dean of Student Affairs in the Faculty of Medicine. Using statistical package for the social sciences, responses were statistically analyzed. Pearson's chi-square test was used to calculate p-values, where p < 0.05 was considered statistically significant. Results A total of 244 eligible medical students, 121 males and 123 females, were included in the study, with a mean age of 21 (±2) years. Similarly, 126 (51.6%) were preclinical students (2nd-4th-year students), while 118 (48.4%) were clinical students (5th-7th-year students). About 79.8% of medical students believed that plastic surgery plays an essential role in trauma management, whereas 9.2% did not consider plastic surgery significant for trauma management. This study found that only 15.5% of medical students were interested in enrolling in plastic surgery residency after graduation, while 47.1% of students did not consider plastic surgery residency after graduation. However, 37.4% were uncertain. The two most driving factors in deciding on plastic surgery residency were expected income (61.8%) and lifestyle (14.3%). Conclusion Improving medical students' education quality can enhance their perception and awareness of plastic surgery. Students should be taught the broader scope of plastic surgery. The inclusion of formal training during undergraduation is the essence of time and should be added to or improved during plastic surgery rotations with more emphasis on reconstructive and hand/peripheral nerve surgery. Student-led interest groups can be a useful tool for educating students about their specialty.

• The Journal of Fisheries Business Administration
• /
• v.17 no.2
• /
• pp.65-106
• /
• 1986

1, The Purpose of Study This is a study on the Evaluation of the operating of Fisheries Extension Services of Korea, for performing the activities such as guiding fisheries technique as well as offering industrial information to the fishermen in fishing village. By doing so, the Fisheries Extension Sevices(FES) can materialize the continued growth of fisheries, the social and economic development of fishing village, and the increase in income by enhancing the knowledge level of Fishermen, etc. In performing fisheries policy, this activity plays a great role on the research and development activity, and it has become practical since 1976 in Korea. In order to meet immediately with the problem of fisheries technical innovation and rapid environmental changes surrounding the fisheries, the fishermen should not only enhance their scientific and comprehensive capacity in fisheries technique but abtain various effective information. Generally, as most of all the fishemen are poor in the managerial structure and scattered in fishing villages, they have little opportunity in the contact of information. As a result, it is nessessary for the FES to perform the fishing business by the extension service officials who has received special training and acquired fisheries know-how in these fields. And yet, FES is under the unfullfilled circumstance in such factors as manpower, technical know-how, equipment, and the service system etc., which is required in promoting the social, economic development of fishing village and in resolving the high technique demand of fisherman. This study on the fisheries extension services have been studied from those backgrounds. 2. Research Method The data of collecting methods which were necessary in carrying out this study was adopted by the questionaire research on the present extension service activity, through the subject of the extension services (driving agency of the work and the officials), the object(fishemen) and the 3rd observers to the extension services (the authorities concerned). The research sample was taken by the sampling extraction of total 1, 774 men from the above 3 groups. And the research was carried out from August, 1986 to October, 1986, supported from the Fisheries Extension Office (FEO) located in field during the research process. In this study, the levels of the extension operating were determined and estimated in accordance with the extension service method, morale of extension service officials and the extension service system, etc. through the collected data of the research questionaire paper. And based on this result, the essential conditions of the extension services were grasped, and also we tried to present the various activity plan necessary to promote the operating of the extension services. The questionaire research data was calculated by the computer center of National Fisheries University of Pusan, and the total result was again tried on the one demension analysis along with two dimension analysis to search out the relativity between the questionaire, and the statistical test was done $\chi$$^2$test in significance level of l~5%. 3. Contents of Study This study consists of 7 chapters and the contents are as follows : Chapter I : The object and method of the study Chapter II : The assessment and analysis of the extension services Chapter III : The contents and method of the extension services Chapter IV : Analysis of the essential conditions for the extension services Chapter V : The evaluation of activities of extension services Chapter Ⅵ : Conclusion.4. Results and RecommendationTherefore, the results of this study estimated by logical process and analysis are as follows : 1) Most of Korean fishing villages and coastal fishermen have shown much concerns about fisheries technique and social changes, thus many of them were confronted with new problems on how to adapt and to meet changes. 2) Majority of fishermen estimated FEO as an organization of specific technologies with all the thing concerning the fisheries technique in general. Therefore the fishermen wanted to utilize the FEO as an adaptable method for the modern fisheries techniques as well as the environmental changes. 3) In contrast with the fast changes of the fisheries technique, the complexity and variety of technical system and the broadness of fishing village and fishermen, it was revealed that the necessary factors such as the facilities, manpower, budget, and the level of applying techniques of the FEO located in field were highly insufficient. Accordingly, the guiding efficiency was low and the extension services did not provide full solution to the various request from fishermen. 4) It is possible to classify the activation factor for the extension service into two large dimension ; personal dimension relevant to guidance officials and work dimension relevant to the organization. And it was found that the activation level of the work dimension was far lower than the personal dimension between them. So, the activation should be done first in the dimesion to promote the activation of the extension services. 5) The extension services officials are now demoralized in general, thus it is necessary to take reality into consideration : the expense of activity, the adequate endowment of activity scope and the reasonable operation of the position class, etc to enhance its morale. However, in order to do the FES activation, first of all, the systems should be established which is lain unsettled stage until now. And there must be change in the understanding of government i.e. the fisheries extension services are the essential policy subject to build up the base of fisheries growth and modernize the fisheries management. And it should be driven positively with the recognition of the "lasting project".g project".uot;.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.2021-2031
• /
• 2013

Due to the rapid economic growth within the nation, the quality of life of individuals have improved dramatically. The scope of living activities of individuals have also extended, resulting in a rapidly increasing demand for automobiles. The number of vehicles registered in Korea is rapidly increasing and will reach 188.71 million as of December 2012. Compared to the registered residents of 50.94 million provided by the Ministry of Public Administration and Security, the registered population reflects about 4 people per every automobile. Due to the high demands for vehicles, the demands for parking lots in collective housing and businesses are also increasing. In reality, the current state of expansion of parking lots are underground, due to the limited available space on ground level. Specifically, the slope of a parking lot cannot exceed 17% linear slope and 14% curved slope according to the 'parking lot laws', however studies show that the driver feels at risk for safety when stopped on the parking ramp while driving in the parking lot. This study seeks to examine the suitability of parking lot ramps, concerning the safety aspects of the driver. First, the ramp type was categorized as linear or curved, then test drives were performed based on variations of slopes, slant distances, directions and points. A survey was administered to the driver after the completion of the test drive, in order to element design for an ideal ramp. In the case of curved ramp, the results of the estimate suggests a counterclockwise, slope at a maximum of 12% incline. The maximum slope for a linear ramp was analyzed to be between 13~14%, suggesting that slope greater than 15% need to be eliminated. In conclusion, it is anticipated that the element design parking ramp reported in this study will help to serve as a reference for future parking lot related guidelines, and provide cost effective traffic safety mechanisms in future parking lot businesses to follow.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Journal of the Korean Society of Radiology
• /
• v.17 no.3
• /
• pp.441-447
• /
• 2023

Lead(Pb), which is currently mainly used for shielding purposes in the medical radiation, has excellent radiation shielding functions, but is continuously exposed to radiation directly or indirectly due to the harmfulness of lead itself to the human body and the inconvenience caused by its heavy weight. Research on shielding materials that are human-friendly, lightweight, and convenient to use that can block risks and replace lead is continuously being conducted. In this study, based on the commonly used polyethylene terephthalate (PET) film and the fabric material used in actual radiation protective clothing, a multi-layer thin film was realized through sputtering and vacuum deposition of bismuth, tungsten, and tin, which are metal materials that can shield radiation. Thus, a shielding film was produced and its applicability as a radiation shielding material was evaluated. The radiation shielding film was manufactured by establishing the optimized conditions for each shielding material while controlling the applied voltage, roll driving speed, and gas supply amount to manufacture the shielding film. The adhesion between the parent material and the shielding metal thin film was confirmed by Cross-cut 100/100, and the stability of the thin film was confirmed through a hot water test for 1 hour to measure the change of the thin film over time. The shielding performance of the finally realized shielding film was measured by the Korea association for radiation application (KARA), and the test conditions (inverse wide beam, tube voltage 50 kV, half layer 1.828 mmAl) were set to obtain an attenuation ratio of 16.4 (initial value 0.300 mGy/s, measured value 0.018 mGy/s) and damping ratio 4.31 (initial value 0.300 mGy/s, measured value 0.069 mGy/s) were obtained. by securing process efficiency for future commercialization, light and shielding films and fabrics were used to lay the foundation for the application of films to radiation protective clothing or construction materials with shielding functions.

• The Journal of Korean Society for Radiation Therapy
• /
• v.27 no.2
• /
• pp.157-166
• /
• 2015

Purpose : Cyber-Knife tumor tracking system, based on the correlation relationship between the position of a tumor which moves in response to the real time respiratory cycle signal and respiration was obtained by the LED marker attached to the outside of the patient, the location of the tumor to predict in advance, the movement of the tumor in synchronization with the therapeutic device to track real-time tumor, is a system for treating. The purpose of this study, in the cyber knife tumor tracking radiation therapy, trying to evaluate the accuracy of tumor tracking radiation therapy system due to the change in the form of unpredictable sudden breathing due to cough and sleep. Materials and Methods : Breathing Log files that were used in the study, based on the Respiratory gating radiotherapy and Cyber-knife tracking radiosurgery breathing Log files of patients who received herein, measured using the Log files in the form of a Sinusoidal pattern and Sudden change pattern. it has been reconstituted as possible. Enter the reconstructed respiratory Log file cyber knife dynamic chest Phantom, so that it is possible to implement a motion due to respiration, add manufacturing the driving apparatus of the existing dynamic chest Phantom, Phantom the form of respiration we have developed a program that can be applied to. Movement of the phantom inside the target (Ball cube target) was driven by the displacement of three sizes of according to the size of the respiratory vertical (Superior-Inferior) direction to the 5 mm, 10 mm, 20 mm. Insert crosses two EBT3 films in phantom inside the target in response to changes in the target movement, the End-to-End (E2E) test provided in Cyber-Knife manufacturer depending on the form of the breathing five times each. It was determined by carrying. Accuracy of tumor tracking system is indicated by the target error by analyzing the inserted film, additional E2E test is analyzed by measuring the correlation error while being advanced. Results : If the target error is a sine curve breathing form, the size of the target of the movement is in response to the 5 mm, 10 mm, 20 mm, respectively, of the average $1.14{\pm}0.13mm$, $1.05{\pm}0.20mm$, with $2.37{\pm}0.17mm$, suddenly for it is variations in breathing, respective average $1.87{\pm}0.19mm$, $2.15{\pm}0.21mm$, and analyzed with $2.44{\pm}0.26mm$. If the correlation error can be defined by the length of the displacement vector in the target track is a sinusoidal breathing mode, the size of the target of the movement in response to 5 mm, 10 mm, 20 mm, respective average $0.84{\pm}0.01mm$, $0.70{\pm}0.13mm$, with $1.63{\pm}0.10mm$, if it is a variant of sudden breathing respective average $0.97{\pm}0.06mm$, $1.44{\pm}0.11mm$, and analyzed with $1.98{\pm}0.10mm$. The larger the correlation error values in both the both the respiratory form, the target error value is large. If the motion size of the target of the sine curve breathing form is greater than or equal to 20 mm, was measured at 1.5 mm or more is a recommendation value of both cyber knife manufacturer of both error value. Conclusion : There is a tendency that the correlation error value between about target error value magnitude of the target motion is large is increased, the error value becomes large in variation of rapid respiration than breathing the form of a sine curve. The more the shape of the breathing large movements regular shape of sine curves target accuracy of the tumor tracking system can be judged to be reduced. Using the algorithm of Cyber-Knife tumor tracking system, when there is a change in the sudden unpredictable respiratory due patient coughing during treatment enforcement is to stop the treatment, it is assumed to carry out the internal target validation process again, it is necessary to readjust the form of respiration. Patients under treatment is determined to be able to improve the treatment of accuracy to induce the observed form of regular breathing and put like to see the goggles monitor capable of the respiratory form of the person.

• Korean Business Review
• /
• v.17
• /
• pp.153-183
• /
• 2004

The Gaisong Merchants can be regarded to playa pioneering role to activate the Korea's trade with foreign countries. In the early period of Yi-Dynasty, the Gaisong Merchants focused on personal trade, but in the middle period of Yi-Dynasty, they entered to the realm of governmental trade. Furthermore, their business activities widened to various forms of trades, for example, smuggling. Utilizing accumulated capital, Gaisong merchants expanded their trading activities to their neighboring countries such as Japan and China. In recent times, it is necessary for modem Korean companies to diversify risks through the establishment of corporations for production, marketing and R&D abroad or through joint venture, M&A and strategic alliance with foreign companies in order to reduce the risks originated from volatile economic and political situations. In this study, we utilize tools of comparative study to compare Gaisong Merchants' foreign trade strategies with those of modem companies such as AMOREPACIFIC, HANILCEMENT and SHINDORICO. The purpose of the paper is to test the hypothesis that modem Korean companies grew up by following the cases of Gaisong Merchants' business activities. We summarize our main findings as follows. First, both Gaisong Merchants and modem Korean companies have common functional core capability in the field of marketing, manufacturing technology, R&D, and human resources development. Second, both Gaisong Merchants and modem Korean companies have common organizational core capability. Third, both Gaisong Merchants and modem Korean companies have common infrastructures such as planning, finance, accounting and MIS. It constitutes the infrastructure of Korea's foreign trade sector. Fourth, both Gaisong Merchants and modem companies have common organizational culture in the field of management policy and philosophy. Actually, those factors are evaluated to be driving forces of Koera's success in foreign trade. In conclusion, the business activities of Gaisong Merchants who represented the peculiarity of Korean business spirit are partially inherited to current Korean business management. The value system and behavior pattern of modern Korean companies is succeeded from the spirit of Gaisong Merchants and it playa major role to specify the identity of Korean business administration.