• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.624-629
• /
• 2008

When TBM excavates a tunnel, existing concrete lining segments are used as supporting structures for driving force. Axial stress on the lining segments are apt to be large in case of direct driving force. However, it drastically decline as it is farther and father from TBM and later, it tends to converge after a certain point. Such tendencies show similar results of finite element analysis. At the initial intervals, the values of finite element analysis are larger, while at the later intervals, the actual stress values are larger. It concludes that such tendencies are attributable to that the concrete lining segments have partially burst and cracked in the axial direction at the initial intervals. And differences of stresses at the later intervals are created by the changed plasticity of ground and the friction on the external sides of the lining segments.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.11
• /
• pp.1065-1071
• /
• 2012

In this paper, we proposed a method for vehicle monitoring with trajectory reconstruction. For safety, it is important to monitor the driving habit of driver. Every year, many accidents occur due to the reckless driving of the driver. Continuous monitoring of the status of commercial vehicles is needed for safety through the entire path from start point to the destination. To monitor the reckless driving, we try to monitor the trajectory of the vehicle by using vehicle's lateral acceleration data. Compared with steering angle and lateral acceleration, these resemble each other. So, we find the relationship of steering angle and acceleration, and find the global direction of vehicle. We find the position of non-GPS section with EKF (External Kalman Filter) and reconstruct the whole trajectory during vehicle driving.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.1
• /
• pp.45-58
• /
• 2002

In this paper, we designed the circuit of drive control for towing winch. It is composed of reference voltage circuit for driving voltage reference, low pass filter circuit for noise reduction, dead zone circuit for initial transient input, and driving circuit for drum direction/velocity control. Also it is realized a drive control circuit for towing winch drum in accordance with PWM(pulse width modulation) method to suit it's purpose of a large capacity driving system. The performance of the designed circuit is analyzed by experiments and the appliablity for driving the towing winch drum satisfactorily is evaluated through a various testing.

• Journal of Drive and Control
• /
• v.21 no.1
• /
• pp.53-58
• /
• 2024

With the recent development of intelligence and automation technologies for construction machinery, the demand for safety and efficiency of road-cutting operations has continued to increase. In response to this, a double-blade road cutter has been developed that can automatically cut roads. However, a double-blade road cutter has a load difference between the two blades due to the ground and wear conditions of the cutting blades. The difference in load between the two blades distorts the direction of travel of the cutter. In this study, a vision sensor-based driving guide technology was developed to correct the driving path of road cutters. In addition, we developed a load-sensing technology that detects blade loads in real-time and controls driving speed in the event of overload.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.868-870
• /
• 2001

Salient pole rotor type single phase SRM(switched reluctance motor) can be use axial direction magnetic flux and radial direction magnetic flux at the same time. Then, it has higher energy density per unit volume and can be lessened the shaft length of motor or exciting magnetic force. Additionally, it's durability is good because it is simple structure and driving device. Prototype of Salient pole rotor type single phase SRM was fabricated by using parameters of three phase SRM and 3D FEM analysis. Also, driving device was fabricated for prototype. Speed and torque characteristic was confirmed through the experiments, and flux linkage, which is important parameter of SRM for generating torque, was measured. The induction emf was calculated by using ideal inductance graph and current graph. Calculated emf and measured emf was compared for confirming loss of prototype in this paper.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.914-917
• /
• 2002

We have obtained high performance and low voltage driving OCB panel by reducing the critical voltage and retardation matching between liquid crystal layer and compensation films. The critical voltage in the panel has been minimized by flattening color filter layer and optimizing a rubbing process. In addition, an appropriate retardation of the film and LC layer has scanned to achieve low driving voltage and high transmission. The proto-type 17" WXGA OCB panel has demonstrated with less than 5V drive and over 80 degree for all viewing direction except for rubbing direction with over 90% of TN light efficiency.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2341-2343
• /
• 2002

This paper describes a vision-based line recognition and control of driving direction for an AGV(autonomous guided vehicle). As navigation guide, black stripe attached on the corridor is used. Binary image of guide stripe captured by a CCD camera is used. For detect the guideline quickly and extractly, we use for variable thresholding algorithm. this low-cost line-tracking system is efficiently using pc-based real time vision processing. steering control is studied through controller with guide-line angle error. This method is tested via a typical agv with a single camera in laboratory environment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.261-264
• /
• 2003

In this paper, a disk-type piezoelectric transformer for the high power was investigated with the variation of road resistance. The diameter and thickness of a disk-type piezoelectric transformer was 45mm and 4mm, respectively. The piezoelectric ceramics was composed to PZT-PMN-PSN. The ratio of driving electrode and generating electrode is 2:1. The poling direction of driving part and generating part are the same. A voltage step-up ratio increased with increasing the load resistance, $R_L$, so it reached 60 under no road resistance. Also, the maximum efficiency of 97% was obtained.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.32 no.1
• /
• pp.26-33
• /
• 2009

The directions of the road are divided into two, the right-hand side and left-hand side of the road, by the convention and specific native method in the world. This paper deals with the characteristics and behaviors of drivers who are accustomed to driving on right-hand side of the road, drive with a handle on the left-hand side, and comparing with left-hand side drivers. The driver's eye movements were measured by eye camera and questionnaires were used for measuring subjective evaluation such as driving mental workload. The experimental results indicated even if the experts who had much experience on right-hand side driving, they had lower driving skill than novice driver, accustomed to driving on left-hand side. In terms of mental workload, MCH rating scale and MNASA-TLX, the right-hand side drivers were in lower stress condition than the left-hand side drivers because of having much driving experience. However, they conducted a few mistakes by confusing the position of turn signal and windshield wiper because of their driving habit or traits and it lead to operation mistakes. These results can be applied effectively to develop the driving support information with changed environments.

• The Journal of Korea Robotics Society
• /
• v.6 no.4
• /
• pp.323-333
• /
• 2011

Due to the limited pendulum motion range, the conventional one-pendulum driven spherical robot has limited driving capability. Especially it can not drive parallel direction with center horizontal axis to which pendulum is attached from stationary state. To overcome the limited driving capability of one-pendulum driven spherical robot, we introduce a spherical robot, called KisBot II, with a new type of curved two-pendulum driving mechanism. A cross-shape frame of the robot is located horizontally in the center of the robot. The main axis of the frame is connected to the outer shell, and each curved pendulum is connected to the end of the other axis of the frame respectively. The main axis and pendulums can rotate 360 degrees inside the sphere orthogonally without interfering with each other, also the two pendulums can rotate identically or independent of each other. Due to this driving mechanism, KisBot II has various motion generation abilities, including a fast steering, turning capability in place and during travelling, and four directions including forward, backward, left, and right from stationary status. Experiments for several motions verify the driving efficiency of the proposed spherical robot.