• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.12
• /
• pp.1222-1229
• /
• 2007

In this paper, we propose a new obstacle negotiation method for the rescue robot. The rescue robot has a variable geometry single-tracked mechanism, so it can maximize a contact length with ground for the adaptability to off-road and pursue a stable system due to the lower center of gravity. In this research, we add the basis of autonomous navigation, driving mode control based on obstacle detection, to the robot to realize automation of mode transformation. Obstacle detection using PSD(Position Sensitive Device) infrared sensors gives active transformation of the track shape. Finally, experimental results about mentioned are presented.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.1-5
• /
• 2000

This paper presents a new sort of multilayer piezoelectric ceramic transformer for switching regulation power supplies. This piezoelectric transformer operate in the second thickness resonant vibration mode. Accordingly its resonant frequency is higher than 1 NHz, Because output power is low if input and output part of transformer are consisted of single layer, this research suggests a new method, which is consisted of both input and output part of transformer have 2-layered piezoelectric ceramics, The size of transformer is 20 mm in width and length, and 1.4 mm in thickness, respectively, To design a high efficient switching circuit of the transformer, internal circuit parameters were measured and then weve calculated a parameter of inductor nd capacitor to design a driving circuit, Weve used a MISFET and its driver circuit modified a calp oscillator circuit as the primary switching circuit.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.861-865
• /
• 2001

Generally the noise and vibration characteristics of 4WD vehicle is closely related to the characteristics of driveline such as bending mode, torsional mode, unbalance and nonuniformity of propeller shaft. In this paper the 4WD vehicle which has body vibration problem in high speed driving condition was tested. The sources of the body vibration and its transfer path are investigated by experimental approach. According to the experimental assessment, the body vibration is caused by the nonuniformity of joint of propeller shaft. And this paper presents a kinematic model of a vehicle driveline for the optimization of a driveline characteristics. Finally the optimized result of the drive line has been verified through the experiment.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.7 no.2
• /
• pp.61-70
• /
• 2012

This paper describes terrain-adaptive attitude controller for a hybrid mobile platform which operates in wheel & track mode. The wheel mode of the hybrid mobile platform allows quick driving performance in the flatland, while the track mode provides adaptive movement in the rough ground or stairway. The switching of the platform between two modes is automatically controlled by attitude controller algorithm. In addition, in the track mode, the platform automatically adjusts its attitude angle to overcome the obstacles in front. This paper demonstrates the attitude controller for the aforementioned wheel-track hybrid mobile platform in order to overcome terrain obstacles by using an adaptive method. The driving performance of the hybrid mobile platform has been tested and verified in various surrounding environments in both wheel and track mode. Further, this paper presents the experiments by using the track structure of mobile platform on forming adaptive attitude under various types of obstacles. The practicability and effectiveness of the proposed attitude controller of the platform has been demonstrated in urban building and a test-bed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.645-650
• /
• 2010

In this paper we present the Bimodal-tram simulator using the PXI embedded real-time controllers. The Bimodal-tram is developed in KRRI (Korea Railroad Research Institute). The vehicle can be automatically operated by navigation control system (NCS). For the automatic driving, the vehicle lanes will be marked with permanent magnets that are placed in the ground. The vehicle is controlled by NCS. NCS governs the manual mode and automatic mode driving. The simulator is designed by an identical conception with the real control condition. The dynamic motion of vehicle is simulated by the nonlinear dynamic model. The control computer calculates the control values. The signal interface is linked by CAN communication. The simulation is processed by real-time base. The test driver can see the graphic motion of vehicle and can operate the steering wheel, gas and brake pedal to control direction and velocity of vehicle during the simulation. At present, the simulator is only operated by manual mode. The automatic mode will be linked after the control algorithm is finished. We will use the simulator to develop the control algorithm in the automatic mode. This paper shows the simulator designed for Bimodal-tram using real-time based controller. The results of the test using the simulator are presented and discussed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.5
• /
• pp.493-498
• /
• 2015

The fuel cell vehicle is a type of hydrogen vehicle which uses a fuel cell to produce electricity, powering its on-board electric motor. The fuel cell vehicle driving principle is completely different from the internal combustion engine vehicle. In order to ensure the durable quality of the fuel cell vehicle, durability test mode considering the characteristics of the fuel cell must be developed. In this study, we derived the durability test mode profile through collecting and analyzing fuel cell vehicle driving data. Then, the accelerated durability test mode is developed by adding degradation conditions and is experimentally validated to have an acceleration factor of 5~6.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.4
• /
• pp.324-331
• /
• 2007

This paper studies new estimation method for state of charge (SOC) of the hybrid electric vehicle lithium battery using sliding mode observer. A simple R-C Lithium battery modeling technique is established and the errors caused by simple modeling was compensated by the sliding mode observer. The structure of the sliding mode observer is simple, but it shows robust control property against modeling errors and uncertainties. The performance of the system has been verified by the UUDS test. The test results of the proposed observer system shows robust tracking performance under real driving environments.

• Journal of ILASS-Korea
• /
• v.23 no.4
• /
• pp.234-243
• /
• 2018

Since September 2017, a small diesel vehicle certification test mode has been enhanced from NEDC to WLTC. The main reason for the change of the certification test mode is that the certification test mode of the emission control standard of the diesel vehicle does not sufficiently reflect various driving patterns of the actual roads. Several automakers have developed after-treatment systems such as LNT, SCR, and DPF to meet enhanced emissions regulations. In this study, four small diesel cars were selected for sale in Korea, and the exhaust gas measurement test was performed in the WLTC mode, which reflects the driving characteristics of the actual roads. As a result of test, LNT vehicle exceeded Euro 6 NOx regulation and SCR vehicle satisfied Euro 6 NOx regulation. In addition, both LNT and SCR systems showed high NOX emission characteristics due to speed, RPA and Vxa. For the PN, all test vehicles were fitted with a DPF and met the Euro 6 PN regulations, with similar PN emissions results in LNT and SCR system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.555-561
• /
• 2010

In this paper, the constant current controller is designed to regulate the driving current of a power LED. The controller design model of the power LED including its driving circuit is proposed to design the constant current controller. A buck converter is also introduced to drive the power LED. The PI-based digital controller is implemented to validate the proposed strategy for the power LED driving.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.423-426
• /
• 1999

This paper describes a driving scheme of the series hybrid electric vehicle that we have developed. Both series HEV and parallel HEV are well known. We chose series HEV because it provides good energy efficiency in urban driving and operates in all-electric mode in performance. And engine-Generator is driven at constant speed with constant load to maintain the low emission. And the battery supplies power during high-load and receive energy during low-load