• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.707-710
• /
• 2002

A 120kV/70A high voltage switch has been installed at Korea Atomic Energy Research Institute in Taejon to supply power with Korea Superconducting Tokamak Advanced Research (KSTAR) Neutral Beam Injection (NBI) system. NBI system requires fast cutoff of the power supply voltage for protection of the grid when arc detected and fast turn-on the voltage for sustaining the beam current. Therefore the high voltage switch and arc current detection circuit are important part of the NBI power supply and there are much need for high voltage solid state switches in NBI system and a broad area of applications. This switch consisted of 100 series connected MOSFETs and adopted the proposed simple and reliable gate drive circuit without bias supply, Various results taken during the commissioning phase with a 100kW resistive load and NBI source are shown. This paper presents the detailed design of 120kV/70A high voltage MOSFETs switch and simple gate drive circuit. Problems with the high voltage switch and gate driver and solutions are also presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.89-97
• /
• 2014

As the digital control technologies in automotive industry have advanced, electronic control units(ECUs) play a key-role to improve system performance. Transmission control unit(TCU) is a shifting controller for automatic transmission of which major functions are to determine the shift and manage the shifting process considering the various sensor signal on transmission and driver's commands. As with any ECU in vehicle, TCU performs complex algorithms such as shift control, diagnostic and failsafe functions. However, firmware design analysis is hardly possible by the reverse engineering due to code protection. Transmission simulator is a hardware-in-the-loop simulator which enables TCU to work in normal mode by simulating the electrical signal of TCU interface. In this research, diagnosis and failsafe algorithm implemented on commercialized TCU is analyzed by using the transmission simulator that is developed for wheel loader construction vehicle. This paper gives various experimental results on the proportional solenoid current trajectories for different operating modes, error detection criterion and limphome mode gears for all the possible cases of clutch malfunction. The derived results for conventional TCU can be applied to the development of inherent TCU algorithms and the transmission simulator can also be utilized for the test of TCU to be developed.

• Journal of Drive and Control
• /
• v.17 no.3
• /
• pp.9-14
• /
• 2020

A special purpose machine with two manipulators and quadruped crawler system is being developed to work at disaster sites where it is intended to quickly respond in the initial stages after the event. In this study, a terrain recognition module is developed so that the above special purpose machine can quickly obtain ground information to help choose its path while recognizing objects in its way, this is intended to enhance the remote driver's limited situational awareness. Terrain recognition modules were developed for two tasks (real-time path guidance, precision terrain measurements). The real-time path guidance analyzes terrain and obstacles while moving, while the precision terrain measurement feature provides more accurate terrain information by precisely measuring the ground in front of the vehicle while stationary. In this study, an air-cooled sensor protection module was developed so that the terrain recognition module can continue its vital tasks in the event of exposure to foreign substances, including scattered dust, mist and rainfall, as well as high temperatures.

• Environmental Engineering Research
• /
• v.23 no.3
• /
• pp.265-270
• /
• 2018

This study was to measure the exposure of diesel vehicle drivers to elemental carbon (EC) as an indicator of diesel particulate matter (DPM) emitted from diesel vehicles in an underground coal mine over 3 years as per NIOSH Method 5040. Our study results (range $10{\mu}g/m^3-377{\mu}g/m^3$ for the loader drivers, $19{\mu}g/m^3-162{\mu}g/m^3$ for the SMV drivers) were similar or less than previous study results (range $5{\mu}g/m^3-2,200{\mu}g/m^3$) for normal mine operations. From this study results, it appeared that the exposures decreased in the second and the third year. It is thought that the reasons for the decreased personal DPM (EC) exposures over the 3 years were related to the following recommendations; more frequent monitoring and maintenance of the diesel vehicles and their DPM filtration systems, more consistent monitoring of the mine's ventilation system and changes of work practices such as minimizing the opening of diesel vehicle windows. An educational program on adverse health effects of exposure to DPM and use of respiratory protection (P2 respirators) also assisted in minimizing driver exposure to DPM.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.271-278
• /
• 2011

This paper presents a LLC resonant controller IC for secondary side control without external active devices to achieve low profile and low cost LED back light units. A gate driving transformer is adopted to isolate the primary side and the secondary side instead of an opto-coupler. A new integrated dimming circuitry is proposed to improve the dynamic current control characteristic and the current density of a LED for the brightness modulation of a large screen LCD. A dual-slope clock generator is proposed to overcome the frequency error due to the under shoot in conventional approaches. This chip is fabricated using 0.35 ${\mu}m$ BCD technology and the die size is $2{\times}2\;mm^2$. The frequency range of the clock generator is from 50 kHz to 500 kHz and the range of the dead time is from 50 ns to 2.2 ${\mu}s$. The efficiency of the LED driving circuit is 97 % and the current consumption is 40 mA for a 100 kHz operation frequency from a 15 V supply voltage.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.69-76
• /
• 2007

This paper presents the design of LVDS (Low-Voltage-Differential-Signaling) transmitter for Gb/s-per-pin operation. The proposed LVDS transmitter is designed using BiCMOS technology, which can be compatible with CMOS technology. To reduce chip area and enhance the robustness of LVDS transmitter, the MOS switches of transmitter are replaced with lateral bipolar transistor. The common emitter current gain($\beta$) of designed bipolar transistor is 20 and the cell size of LVDS transmitter is $0.01mm^2$. Also the proposed LVDS driver is operated at 1.8V and the maximum data rate is 2.8Gb/s approximately In addition, a novel ESD protection circuit is designed to protect the ESD phenomenon. This structure has low latch-up phenomenon by using turn on/off character of P-channel MOSFET and low triggering voltage by N-channel MOSFET in the SCR structure. The triggering voltage and holding voltage are simulated to 2.2V, 1.1V respectively.

• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.91-100
• /
• 2007

The most important thing for driver's safety on the road is equipment of crash cushion as a vehicle protection safety facility. But development of crash cushion is defective because there's no rational and reality way of design. And also without an alternative plan, it rely on crash test hereby it suffers a great economic loss and wastes time. This study that uses data of cash test proves the suitability of single degree of freedom which considers the safety of passengers about three-dimensional complicated Crash Analysis. As the study analyzes the conduct of crash cushion, it want to develop the effective method of design on Single Degree of Freedom Crash Cushion. And it presents the way of crash cushion design through making a crash analysis model with single degree of freedom. To verify the validness of the crash cushion plan, with single degree of freedom plan, we make the level CC2 crash cushion and execute the crash test. A performance test brings satisfied result and a plan of single degree of freedom crash cushion is proven as an one of the way to be a good system which can design crash cushion.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.67-74
• /
• 1998

The primary cause of air pollution by vehicles is imperfect combustion of fuel. One of the most usual causes of this imperfect combustion is the misfire in IC engins. The U.S. EPA(Environment Protection Agency) and the CARB(California air Resources Board) have imposed regulations for the detection of misfiring in automotive engines. The OBD-II regulations require that misfire should be monitored by the engine diagnostic system, and that the goal of OBD-II is to alert the driver to the presence of a malfunction of the emission control system. Several solutions to the misfire detection problem have been proposed for the detection of misfires. However, the performance of these methods in the presence of misfire is not altogether clear. This paper presents a precise method and system for internal combustion engine misfire. Present invention based upon measurements of engine roughness as derived from crankshaft angular velocity measurements with special signal processing method. Crankshaft angular velocity signals are processed by WDPT, so that the more reliable misfire detection than the time domain analysis. Experimental work confirms that it is possible to apply the WDFT for the detection of misfires in no-load idle and road testing.

• Korean Security Journal
• /
• no.41
• /
• pp.387-408
• /
• 2014

South Korea already became an aging society, and is now in the process of becoming an aged society. With increasing elderly population, elderly safety issues such as traffic accidents and elderly suicides are becoming important problems. Elderly victimization are increasing, and elderly safety accident is also becoming an imporotant social problem. The police is doing various activities for elderly safety. The police is conducting programs for the elderly, such as a prevention program for fraud against elderly, and safety checks and traffic safety education for preventing elderly traffic accidents. Also, there's a program of providing regular visits for a lone elderly, expansion of CCTV network and fingerprint registration to prevent elderlies with Alzheimer's disease going missing. However, these programs are not done on a national scale, but rather limited to local police stations. The purpose of this study is to seek police roles for enhancing elderly safety, due to lack of police activity in this area. Recommendation for police roles in enhancing elderly safety is to first conduct routine crackdowns on fraud against elderly and also conduct education programs for preventing fraud. Also, crimes such as elderly abuse is lead by elderly protection agencies, but considering elderly abuse is a crime, the police should take a leading role. Also, to prevent elderly suicide, meticulous management of elderlies with high suicide risk is necessary, and elderly protection areas should be designated to prevent traffic accidents. Also, elderlies should be induced to turn in their driver's license. To conduct these matters of elderly safety, an organization exclusively charged with elderly safety is necessary. Elderly safety is a broad concept, and since police alone cannot handle the task of ensuring elderly safety, the police should take on a leading role in cooperative efforts with various institutions of the government, non-profit organizations and the community to establish a social saftey net for elderly safety.

• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.289-297
• /
• 2018

The vehicle lubricant has captured 35% of the total lubricant market while the engine oil possessed 77% of the vehicle lubricant market in Korea. The suitable quality management of circulating engine oil is thus required for the driver and engine protection. But, KS and synthetic engine oil products (containing over 30% synthetic oil) are exempt to any quality inspections under Petroleum and Alternative Fuel Business Act. In this study, our research group investigated the quality monitoring of 30 kinds of domestic distributing synthetic engine oils. Two kinds of the engine oil showed an off specification from the test results; one engine oil is an imported and the other is a KS synthetic one. Also, the pattern of engine oils were analyzed using SIMDIST (simulated distillation) and the most engine oils had a broad carbon number spectrum, which is a typical of mineral oils except several imported products. Thus, we concluded that relevant laws for the proper quality management of synthetic oils and KS products are needed to be established for preventing consumer's damages.