• Journal of Mechanical Science and Technology
• /
• 제14권10호
• /
• pp.1021-1027
• /
• 2000

In this study, fatigue tests were performed to examine the effects of micro drill hole on fatigue limit of as cast and austempered ductile cast iron (ADI) using the rotary bending fatigue tester. As results, micro drill holes ($diameter{\leq}0.4mm$) did not influence the fatigue limit of ADI, compared to annealed ductile cast iron; the critical defect size of crack initiation, in ADI was larger than as cast. If the ${\sqrt{area}}$ of micro drill hole and graphite nodule in ADI are comparable, crack initiates at the graphite nodule. When the ruggedness developes through austempering treatment process, microstructure on crack initiation at micro drill hole is tougher than that of as cast ductile cast iron.

• 한국정밀공학회지
• /
• 제2권2호
• /
• pp.43-59
• /
• 1985

In relation to the machinability of drilling operation, experiments were made to investigate the effect of cutting condition on static as well as dynamic cutting resistances in cutting plane carbon steel (SM 45 C) with H.S.S. twist drills. The results were as follows. 1) The static cutting resistances on carbon steel can practically be calculated by the following equations which were derived from experimental result. The deviation from the experimental values was less than 8% and 13% for cutting torque and thrust respectively. For cutting torque M: M=0.019 $H_B\;{f^{0.68}d^{1.68}$ For thrust T: T=0.400406 $r^{0.6}d^{0.68}$ + 0.1835 $H_BC^2$(where $H_B$: Brinnel hardness) 2) The static components of cutting resistance are increased exponentially with increasing drill diameter and feed rate. On the effect of drill diameter, the dynamic components of torque are decreased with increasing dirll diameter because of rigidity, the dynamic components of thrust being not effected with the changes. 3) As feed rates increase, the dynamic components of torque rather decrease although its changes on thrust components are unstable. 4) The static components of cutting resistance and dynamic component of torque are slightly decreased in accordance with the increase of spindle speed although its dynamic thrust components are not effected by the spindle speed.

• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.15-20
• /
• 2005

This paper describes the PCB drilling using an ultra high-speed air bearing spindle system and micro drill. For this research, we have developed the ultra high-speed air bearing spindle of 125,000 rpm and made an experiment for the application possibility in the PCB drilling. In order to estimate the drilling performance, we have investigated the size and damage of drilled hole, and the wear of drill at 90,000rpm. Results are as follows; we have confirmed the possibility in the PCB drilling of air bearing spindle. In case of micro-drilling PCB at $0.1mm\sim0.3mm$, the increase in the number of drilling has resulted in a bigger size of holes and also a bigger size of damage. It has been found that the wear of micro drill tends to concentrate in the main cutting edge.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.142-147
• /
• 2012

Machining tool conditions directly affect to quality of product and productivity of manufacturing. Many researches performed for tool condition monitoring in machining process to improve quality and productivity. Conventional methods use characteristics of signal for cutting force, motor current consumption, vibration of machine tools and machining sound. Recently, diameter of machining tool is become smaller for minimizing of mechanical parts. Tool condition monitoring using conventional methods are relatively difficult because micro machining using small diameter tool has low machining load and high cutting speed. These days, the direct monitoring for tool conditions using vision system is performed actively. But, vision system is affected by external conditions such as back ground of image and illumination. In this study, minimizing technology of external conditions using distribution analysis of image data are developed in micro machining using small diameter drill and tap. The image data is gathered from vision system. Several sets of experiment results are performed to verify the characteristics of the proposed machining technology.

• Clinics in Shoulder and Elbow
• /
• 제13권1호
• /
• pp.72-78
• /
• 2010

목적: 견관절의 Bankart 병변에 대하여서 관절경적 수술하에서도 골경유 봉합이 가능하도록 유연성 골 천공기를 개발하였으며 이에 대한 동물 실험 및 임상 증례를 보고하는 바이다. 대상 및 방법: 유연성 천공기 세트는 유연성 천공기와 유도관으로 구성되어 있다. 유연성 천공기는 49개의 미세강선들이 단일 강선 (직경 1.2 mm)으로 꼬인 구조로 이루어져 유연성이 있으며 이러한 유연한 강선의 한 쪽 끝에는 천공기 (직경 1.2 mm)가 용접되어 있는 구조로 이루어져 있다. 유도관은 외경 3.0 mm, 내경 2.0 mm의 원통형 금속 도관으로 이루어져 있으며 한 쪽 끝은 30도 정도 굴곡되어 있다. 기기의 내구성 및 임상적 유용성을 시험하기 위하여 돼지의 견갑골 관절와에 골 천공을 실시하는 실험을 30회 이상 실시하였다. 유연성 강선 부위의 기계적 파단이나 골 천공의 실패 등은 발생하지 않았다. 일반적 견관절 관절경 술식대로 견관절의 후방 입구 및 전 상방, 전 후방 입구들을 확보한 후 관절경하에서 Bankart 병변이 확인이 되면 면도기를 이용하여 견갑와 내측면의 변연 절제를 실시하여 골 출혈을 유도한다. 이후 관절경을 전 상방 입구로 이전 시키고, 후방 입구를 통하여서 유연성 골천공기 세트의 유도 강관을 삽입하는데 유도 강관의 끝이 견갑와연에서 약 5 mm 정도 안쪽에 위치되도록 한다. 유도강관 내로 유연성 천공기를 삽입한 후 구동기를 이용하여서 견갑와의 골 천공을 실시한다. 골 천공 후에는 유연성 천공기만 유도강관에서 제거한 후에 유도 강관내로 봉합사를 삽입하여 천공된 골구로 통과시키도록 한다. 봉합 갈고리를 이용하여 관절와순에 유도봉합사를 통과시킨 후에 이 유도봉합사에 골 천공구를 통과한 봉합사를 끼워서 관절완순을 통과하도록 한 후 활주 결찰을 실시하여 골 관통 봉합을 이루도록 한다. 동일한 방식으로 견갑와의 2시, 4시 방향에 골 천공을 시행하여 견갑와순의 봉합을 실시한다. 결과: 외상성 견관절 탈구 환자 5예에서 유연성 골 천공기를 이용한 Bankart 병변의 봉합을 실시하였다. 수술 도중 또는 수술후의 신경이나 혈관 손상 등의 문제점이나 합병증 등은 발생하지 않았으며 기기 자체의 문제들도 발생하지 않았다. 평균 6개월간의 추시 결과 상에서는 재탈구 등의 증상은 나타나지 않았다. 결론: 유연성 골 천공기를 사용한 Bankart 병변의 봉합시 관절경적 수술이면서도 골 관통식 봉합이 가능하여 관절와순의 부착면적의 증대 효과 뿐 아니라 손쉬운 활주 결찰이 이루어 질 수 있음을 보여주었다.

• 소음진동
• /
• 제7권4호
• /
• pp.669-679
• /
• 1997

This paper deals with a study of striker type impact hammer drill for improving the drilling performance. The study was performed through a numerical simulation of the impact hammer mechanism and an experimental comparison of the numerical simulation results was followed. Optimization of the impact mechanism was also performed. The numerical model of the impact hammer drill takes into account the striker motion and the effects of the pressure in the cylinder as well as the friction acting on the striker. The equation of motion is solved with the pressure equation in the cylinder including the friction force. The friction is considered as a combination of Coulomb friction and viscous damping friction. At the moment of impact, an ideal impact model that uses restitution coefficient is used to calculate the sudden change of the striker motion. The numerically simulated impact force shows a good agreement with the experimental result and thus, the validity of the numerical model is proven. Based upon the proposed model, an optimization was performed to improve the impact force of the hammer drill. The objective function is to maximize the impact force and the used design variables are striker mass, frequency of piston, bit guide mass, cylindrical diameter and dimensions of the mechanism components. Each design variable and some other conditions that are essential to manitain normal operation of the hammer drill are considered as constraints. The optimized result show a remarkable improvement in impact force and an experimental proof was investigated.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.268-274
• /
• 2013

Electric discharge machining drill (EDM-drill) is an efficient process for the fabrication of micro-diameter deep metal hole. As there is non-physical contact between tool (electrode) and workpiece, EDM-drill is widely used to machine the hard machining materials such as high strength steel, cemented carbide, titanium alloys. The electro-thermal energy forces the electrode to wear out together with the workpiece to be machined. The electrode wear occurs inside of a machining hole. and It causes hard to monitor the machining state, which leads the productivity and the quality to decrease. Thus, this study presents a methodology to estimated the electrode wear amount while two coefficients (scale factor and shape factor) of the logarithmic regression model are evaluated from the experiment result. To increase the accuracy of estimation model, the linear transformation method is adopted using the differences of initial electrode wear differences. The estimation model is verified through experiment. The experimental result shows that within minute error, the estimation model is able to predict accurately.

• 한국진공학회지
• /
• 제18권5호
• /
• pp.337-345
• /
• 2009

패키지 기판의 지름 $100{\mu}m$ 이하 미세 드릴 구멍의 경우 습식 디스미어 공정만으로는 구멍 내부의 스미어를 효과적으로 제거할 수 없다. 본 연구에서는 습식 디스미어 공정의 이전 단계에서 대기압 플라즈마를 처리하여 소수성의 기판 표면을 친수성으로 개질하고자 하였다. 대기압 플라즈마 공정은 리모트 DBD 방식의 전극을 이용하여 패키지 제조 공정에 적합한 인라인 형태의 장비로 구성되었다. 대기압 플라즈마를 처리한 결과 접촉각 기준으로 $71^{\circ}$의 소수성 절연 필름 표면이 $30^{\circ}$ 정도의 친수성 표면으로 개질되었다. 대기압 플라즈마 처리 유무에 따른 습식 디스미어 공정의 특성을 평가하기 위하여 절연 필름의 두께, 드릴 구멍 지름, 표면 조도의 변화를 측정하였는데, 대기압 플라즈마 처리 시 기판 전면에서 공정 특성의 균일도가 향상되는 것을 확인하였다. 또한 대기압 플라즈마 처리 유무에 따른 드릴 구멍의 SEM 사진 분석 결과 대기압 플라즈마 처리 시 구멍 내부의 스미어가 효과적으로 제거됨을 실험적으로 확인하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.177-182
• /
• 1997

The purpose of this study is to analyze how tools, guide bush type and the change of cutting speed have effects on the diameter of cutting hole, surface roughness of workpiece and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. (1) The diameter was expanded for 25${\mu}{\textrm}{m}$ at the first section and then was reduced 0${\mu}{\textrm}{m}$ and 15${\mu}{\textrm}{m}$ respectively at the 10m and 20m section comparing to the diameter of tool with respect to the variation of cutting length. (2) It was proved that roughness was below 12S for the whole section of cutting length. (3) The roundness has been below 12${\mu}{\textrm}{m}$. Regarding the polygon phenomenon, it has bee proved that not only uneven number of angle but also even number (quadrilateral, elliptical) of angle were made. (4) Variation of diameter, surface roughness of workpiece and roundness turned out to ve the best at 70m/min of cutting speed, 0.15mm/rev of feed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.146-152
• /
• 1997

This paper deals with a study of striker type impact hammer drill for improving the drilling performance. The study was performed through a numerical simulation of the impact hammer mechanism, an experimental comparison of the numerical simulation results and an optimization of the impact mechanism. The numerical model of the impact hammer drill takes into account the striker motion and the effects of the pressure in the cylinder as well as the friction acting on the striker. The equation of motion is solved with the pressure equation in the cylinder and the friction force. At the moment of impact, an ideal impact model that uses restitutiion codfficient is used to calculate the sudden change of the striker motion. The impact force numerically simulated shows a good agreement with the experimental results and thus, the validity of the numerical model is proven. Based upon the proposed model, an optimization was performed to improve the impact force of the hammer drill. The objective function is to maximize the impact force and the design variables are striker mass, frequency of piston, bit guide mass, cylindrical diameter and dimensions of the mechanism components. Each design variable and some other conditions that are essential to maintain normal operation of the hammer drill are considered as constraints. The optimized result shows remarkable improvement in impact force and an experimental proof was investigated.