• Structural Engineering and Mechanics
• /
• 제60권6호
• /
• pp.1021-1038
• /
• 2016

Considerable part of reinforced concrete building has suffered from destructive earthquakes in Turkey. This situation makes necessary to determine nonlinear behavior and seismic performance of existing RC buildings. Inelastic response of buildings to static and dynamic actions should be determined by considering both flexural plastic hinges and brittle shear hinges. However, shear capacities of members are generally neglected due to time saving issues and convergence problems and only flexural response of buildings are considered in performance assessment studies. On the other hand, recent earthquakes showed that the performance of older buildings is mostly controlled by shear capacities of members rather than flexure. Demand estimation is as important as capacity estimation for the reliable performance prediction in existing RC buildings. Demand estimation methods based on strength reduction factor (R), ductility (${\mu}$), and period (T) parameters ($R-{\mu}-T$) and damping dependent demand formulations are widely discussed and studied by various researchers. Adopted form of $R-{\mu}-T$ based demand estimation method presented in Eurocode 8 and Turkish Earthquake Code-2007 and damping based Capacity Spectrum Method presented in ATC-40 document are the typical examples of these two different approaches. In this study, eight different existing RC buildings, constructed before and after Turkish Earthquake Code-1998, are selected. Capacity curves of selected buildings are obtained with and without considering the brittle shear capacities of members. Seismic drift demands occurred in buildings are determined by using both $R-{\mu}-T$ and damping based estimation methods. Results have shown that not only capacity estimation methods but also demand estimation approaches affect the performance of buildings notably. It is concluded that including or excluding the shear capacity of members in nonlinear modeling of existing buildings significantly affects the strength and deformation capacities and hence the performance of buildings.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권2호
• /
• pp.82-88
• /
• 2010

본 연구의 목적은 내진규준이 적용되기 이전에 건설된 역사건물의 내진성능 평가 및 내진보강이다. 이를 위하여 2층 RC 역사건물의 내진성능이 평가되었다. 동적해석에 의한 층간변위비 및 층전단력 평가결과, 층전단력이 설계기준의 밑면전단력을 초과하는 것으로 평가되어 적절한 내진보강이 필요한 것으로 평가되었다. 내진성능 향상을 위하여 총 4개의 강재댐퍼가 사용되었다. 해석 변수는 강재댐퍼 형상 및 설치 방법이다. 동적해석결과 역 K가새로 설치되는 슬릿댐퍼가 다른 댐퍼 형상 및 설치 방법보다 우수한 내진성능을 가진 것으로 평가되었다.

• Earthquakes and Structures
• /
• 제22권2호
• /
• pp.203-218
• /
• 2022

In this paper, quasi-static tests were carried out on three prefabricated reinforced concrete column-steel beam (RCS) sub-assemblages with floor slabs and one comparison specimen without floor slab. The effects of axial compression and floor slab on the seismic performance were studied, and finite element simulations were conducted using ABAQUS. The results showed that the failure of prefabricated RCS sub-assemblages with floor occurred as a joint beam and column failure mode, while failure of sub-assemblages without floor occurred due to beam plastic hinge formation. Compared to the prefabricated RCS sub-assemblages without floor slab, the overall stiffness of the sub-assemblages with floor slab was between 19.2% and 45.4% higher, and the maximum load bearing capacity increased by 26.8%. However, the equivalent viscosity coefficient was essentially unchanged. When the axial compression ratio increased from 0.24 to 0.36, the hysteretic loops of the sub-assemblages with floor became fuller, and the load bearing capacity, ductility, and energy dissipation capacity increased by 12.1%, 12.9% and 8.9%, respectively. Also, the initial stiffness increased by 10.2%, but the stiffness degradation accelerated. The proportion of column drift caused by beam end plastic bending and column end bending changed from 35% and 46% to 47% and 36%, respectively. Comparative finite element analyses indicated that the numerical simulation outcomes agreed well with the experimental results.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권3호
• /
• pp.211-218
• /
• 2006

본 연구에서는 거주형 무량판 구조의 뚫림 전단을 방지하기 위한 연속 절곡된 전단 보강근을 개발하였다. 이를 적용한 슬래브-기둥 접합부에 있어 개발 전단 보강근의 뚫림 전단 성능을 평가하기 위하여, 구조 성능 실험을 수행하였다. 실험 변수는 전단보강근이 없는 경우, 개발 전단보강근을 사용한 경우, 헤드 스터드를 사용한 경우이다. 수평하중에 대한 저항성능을 평가하기 위하여 일정축력하에서의 이력 하중 실험을 수행하였다. 실험결과는 전체 변위 및 접합부 강도 등으로 평가되었다. 이러한 결과로부터, 개발된 전단보강근이 층간변위비 거동에 있어 우수한 성능을 보유함을 확인할 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권2호
• /
• pp.67-76
• /
• 2023

본 연구에서는 기존 내력증진형 내진보강공법의 취약점을 개선 및 보완할 수 있는 새로운 개념의 내진보강법인 내부접합형 합성내진보강공법 (Composite Seismic Strengthening Method, CSSM)을 제안하였다. CSSM 내진보강 시스템은 필요 내진보강량 산정이 간편한 강도증진형 내진보강법의 일종으로서, 전단파괴가 지배적인 우리나라 내진상세를 가지지 않는 기존 R/C 건물에 적용 시 내력증가가 효율적으로 가능한 내진 시스템 공법이다. 제안한 내부접합형 CSSM 공법의 내진안전성을 검토하기 위하여 내진상세를 가지지 않는 우리나라 R/C 건축물을 바탕으로 한 실물 2층 골조 실험체를 대상으로 유사동적실험을 실시하여, 지진에 대한 하중 및 변위 특성, 지진피해수준, 강도증진 효과, 변위제어능력을 중심으로 내진성능을 평가하였다. 유사동적 실험결과 개발공법인 CSSM 내진시스템은 효과적으로 전단내력을 증가시켰으며, 2400년 재현주기인 지진파에 대해서도 지진에 대한 변위를 효과적으로 억제시켰다.

• 한국지진공학회논문집
• /
• 제12권2호
• /
• pp.69-80
• /
• 2008

본 연구에서는 중고층 건물과 같이 고차모드의 영향이 커지는 구조물의 지진에 대한 성능점을 간략하고 정확하게 구할 수 있는 개선된 능력스펙트럼법을 제안한다. 능력스펙트럼법은 주어진 지진의 응답스펙트럼과 다자유도 구조물을 변환한 등가 단자유도 시스템을 이용하여 지진으로 인하여 발생하는 지붕층의 최대 비탄성변위를 간략하게 구하는 방법이다. 제안된 방법에서는 구조물의 탄성 및 비탄성 동적해석을 수행하지 않고, 기존의 능력스펙트럼법에서 요구되는 정적푸쉬오버해석과 탄성변위를 이용하여 비탄성변위를 예측하는데, 기존 연구에서 개발한 $C_R$을 이용한다. 본 연구는 제안한 방법의 정확도를 평가하기 위해 LA 지역의 3, 9, 20층 철골모멘트저항골조를 선택한다. 이 건물들의 지진에 대한 각 층별 최대 층간변위비를 개발한 CSM으로 구하고, 이를 비선형 응답이력해석(NL-RHA)으로 구한 결과와 비교하였다. 사용한 지진은 재현주기 475년과 2475년의 위험수준에 대한 각각 20개의 지진집단들이다. 또한 본 연구에서는 ATC-40에 제시된 CSM 방법과 N2 방법으로 구한 각 건물의 최대 층간변위비도 비교한다. 개발된 CSM은 기존에 개발된 방법에 비하여 보다 정확한 최대 층간변위비를 예측하는 것으로 나타났다.

• Earthquakes and Structures
• /
• 제7권2호
• /
• pp.179-199
• /
• 2014

The steel tube-reinforced concrete (ST-RC) composite column is a novel type of composite column, consisting of a steel tube embedded in reinforced concrete. The objective of this paper is to investigate the effect of cumulative damage on the seismic behavior of ST-RC columns through experimental testing. Six large-scale ST-RC column specimens were subjected to high axial forces and cyclic lateral loading. The specimens included two groups, where Group I had a higher amount of transverse reinforcement than Group II. The test results indicate that all specimens failed in a flexural mode, characterized by buckling and yielding of longitudinal rebars, failure of transverse rebars, compressive crushing of concrete, and steel tube buckling at the base of the columns. The number of loading cycles was found to have minimal effect on the strength capacity of the specimens. The number of loading cycles had limited effect on the deformation capacity for the Group I specimens, while an obvious effect on the deformation capacity for the Group II specimens was observed. The Group I specimen showed significantly larger deformation and energy dissipation capacities than the corresponding Group II specimen, for the case where the lateral cyclic loads were repeated ten cycles at each drift level. The ultimate displacement of the Group I specimen was 25% larger than that of the Group II counterpart, and the cumulative energy dissipated by the former was 2.8 times that of the latter. Based on the test results, recommendations are made for the amount of transverse reinforcement required in seismic design of ST-RC columns for ensuring adequate deformation capacity.

• 한국구조물진단유지관리공학회 논문집
• /
• 제7권4호
• /
• pp.225-233
• /
• 2003

최근 성능에 근거한 설계법의 개발과 더불어, 변위설계에 대한 관심이 증가하고 있다. 본 연구에서는 다층 RC 골조의 변위성능을 보다 정확하게 평가할 수 있는 방법을 제시하고자 한다. 이를 위해, 골조의 횡변위를 계산하기 위해서 보와 기둥의 변형뿐만 아니라 정착부와 조인트 부분의 변형을 변위 산정시 고려하였다. 기존의 실험 및 계산결과의 비교로부터, 본 연구에서 제시한 방법의 적합성을 확인하였고, 이를 강한 기둥-약한 보의 설계개념을 설계된 다층 RC골조 건물에 적용하여 그 거동을 예측하였다. 그 결과, 보다 정확한 건물의 변위성능을 평가하기 위해서는 정착부와 조인트의 변형을 반드시 반영하여야 하는 것으로 나타났다.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.497-507
• /
• 2024

In squat reinforced concrete walls, the displacement capacity for lateral deformation is low and the ability to resist the axial load can quickly be lost, generating collapse. This work consists of testing two squat reinforced concrete walls. One of the specimens is built with conventional detailing of reinforced concrete walls, while the second specimen is built applying an alternative design, including stirrups along the diagonal of the wall to improve its ductility. This solution differs from the detailing of beams or coupling elements that suggest building elements equivalent to columns located diagonally in the element. The dimensions of both specimens correspond to a wall with a low aspect ratio (1:1), where the height and length of the specimen are 1.4 m, with a thickness of 120 mm. The alternative wall included stirrups placed diagonally covering approximately 25% of the diagonal strut of the wall with alternative detailing. The walls were tested under a constant axial load of 0.1f'cAg and a cyclic lateral displacement was applied in the upper part of the wall. The results indicate that the lateral strength is almost identical between both specimens. On the other hand, the lateral displacement capacity increased by 25% with the alternative detailing, but it was also able to maintain the 3 complete hysteretic cycles up to a drift of 2.5%, reaching longitudinal reinforcement fracture, while the base specimen only reached the first cycle of 2% with rapid degradation due to failure of the diagonal compression strut. The alternative design also allows 46% more energy dissipation than the conventional design. A model was used to capture the global response, correctly representing the observed behavior. A parametric study with the model, varying the reinforcement amount and aspect ratio, was performed, indicating that the effectiveness of the alternative detailing can double de drift capacity for the case with a low aspect ratio (1.1) and a large longitudinal steel amount (1% in the web, 5% in the boundary), which decreases with lower amounts of longitudinal reinforcement and with the increment of aspect ratio, indicating that the alternative detailing approach is reasonable for walls with an aspect ratio up to 2, especially if the amount of longitudinal reinforcement is high.

• Earthquakes and Structures
• /
• 제13권5호
• /
• pp.485-496
• /
• 2017

The behavior of 8 steel reinforced high-strength concrete (SRHSC) columns, which comprised of four identical columns with cross-shaped steel and other four identical columns with square steel tube, was investigated experimentally under cyclic uniaxial and biaxial loading independently. The influence of steel configuration and loading path on the global behavior of SRHSC columns in terms of failure process, hysteretic characteristics, stiffness degradation and ductility were investigated and discussed, as well as stress level of the longitudinal and transverse reinforcing bars and steel. The research results indicate that with a same steel ratio deformation capacity of steel reinforced concrete columns with a square steel tube is better than the one with a cross-shaped steel. Loading path affects hysteretic characteristics of the specimens significantly. Under asymmetrical loading path, hysteretic characteristics of the specimens are also asymmetry. Compared with specimens under unidirectional loading, specimens subjected to bidirectional loading have poor carrying capacity, fast stiffness degradation, small yielding displacement, poor ductility and small ultimate failure drift. It also demonstrates that loading paths affect the deformation capacity or deformation performance significantly. Longitudinal reinforcement yielding occurs before the peak load is attained, while steel yielding occurs at the peak load. During later displacement loading, strain of longitudinal and transverse reinforcing bars and steel of specimens under biaxial loading increased faster than those of specimens subjected to unidirectional loading. Therefore, the bidirectional loading path has great influence on the seismic performance such as carrying capacity and deformation performance, which should be paid more attentions in structure design.