• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.203-210
• /
• 1995

The rapid progress of automobile industry has led to a demand for sheet metal products and the new forming technology for complex product is required. In Deep Drawing process of steel sheet, especially stainless steel sheet at room temperture, some intermediate annealing need to be added to lessen strain hardening effect. The present study is concerned with the wram deep drawing of stainless steel sheet. In order to reduce the number of working process. the limit drawing ration is considered as main parameter. In this study, the effect of process variables such a sblank holder force, working temperature and lubricant on limit drawing ration is investigated . Experiments are carried out for the hemisherical and sqare shape at room and warm temperature respectively. The drawing loads and thickness deviation accoring to process variables measured . As the result of apploying those experimental data to the commerical butt product, the number of process can be reduced and good quality of products can be obtained.

• 소성∙가공
• /
• 제21권6호
• /
• pp.348-353
• /
• 2012

Micro-drawn parts have received wider acceptance as products become smaller and more precise. The subject of this study was the deformation characteristics of ultra thin sheet metal in micro drawing of a rectangular shaped part. The influence of drawing speed and blank holding force on the product quality was investigated in micro-drawing of ultra thin sheet of beryllium copper (C1720) alloy. The specimen had a diameter of 4.8 mm and a thickness of $50{\mu}m$. Experiments were carried out in which, different blank holding force and drawing speed were considered. The product quality was evaluated by measuring the thickness and hardness along two specified directions, namely, the side and diagonal directions. The distribution of the thickness strain showed severe thinning especially around the punch radius in both directions. In the diagonal direction, thickening occurred in the flange area due to the axi-symmetric drawing mode. The increase of blank holding force and/or drawing speed was found to cause severe thinning around the punch radius. The blank holding force had a greater effect on thinning of the product than the drawing speed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.235-238
• /
• 2005

In this study, it is investigated that the effect of material properties such as strength coefficient and strain hardening exponent on formability of AZ31 alloy sheet in square cup deep drawing process. Mechanical properties of AZ31 alloy sheet at elevated temperature $250^{\circ}C$ are obtained from uniaxial tensile tests and based on these results, a series of square cup deep drawing tests at the same temperature condition are carried out. Also, the possibilities of necking initiation is predicted by the FEM and FLD and compared with experimental results.

• 한국해양공학회지
• /
• 제14권4호
• /
• pp.86-91
• /
• 2000

Numerical simulation of sheet metal forming for panels as other components has wide acceptance in the automotive industry. Therefore this paper was focused in the drawability factors (which are friction coefficient , radius of die and punch ) on the square cup deep drawing by the explicit finite elements code $PAM-STAMP^{TM}$. The computed results are compared with the experimental results to show the validity of the analysis. In order to compare the simulation results with the experiment results and predict the effect of drawability factors, the relationships between punch load punch stroke, and the relationships between thickness strain and distance are used. According to this study, the results of simulation by using $PAM-STAMP^{TM}$ will give engineers good information to access the drawability of square drawing.

• 대한금속재료학회지
• /
• 제46권3호
• /
• pp.111-117
• /
• 2008

The effects of the dissolved cementite on the mechanical properties have been experimentally investigated. The steel wires were fabricated depending on the carbon content of 0.82 and 1.02 wt.% and drawing strain from 4.12 to 4.32. The bending fatigue resistance and torsion ductility were measured by a hunter fatigue tester and torsion tester specially designed for thin-sized wires. The results showed that as the drawing strain and carbon content increased, the fatigue resistance and the torsional ductility of the steel wires decreased, while the tensile strength increased. In order to elucidate this behavior, the microstructure in terms of lamellar spacing (${\lambda}_p$), cementite thickness ($t_c$) and morphology of cementite was observed by advanced analysis techniques such as transmission electron microscope (TEM) and 3 dimensional atom probes (3-D AP).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.146-150
• /
• 2000

there are a lot of process variable exerted influence on the formability of products in deep drawing process. Particularly it is important that blank shape of the process variables. A paper to be connected with process variables of elliptical deep drawing products is insufficient the actual circumstances enough though researches have been performed on the deep drawing of sheet metal forming. In this study The effects of thickness distribution and movement of sheet are grasped as alteration of blank shapes in the process of elliptical deep drawing product and then optimal blank shape was presented. They were verified by the finite element analysis (FEA) and experiment.

• Journal of Mechanical Science and Technology
• /
• 제15권4호
• /
• pp.459-464
• /
• 2001

The effects of internal air-pressing on deep drawability are investigated in this study to increase the deep drawability of aluminum sheet. The conventional deep drawing process is limited to a certain limit drawing ratio(LDR) beyond which failure will occur. The intention of this work is to examine the possibilities of relaxing the above limitation through the deep drawing with internal air-pressing, aiming towards a process with an increased drawing ratio. The idea which may lead to this goal is the use of special punch that can exert high pressure on the internal surface of deforming sheet during the deep drawing process. Over the ranges of conditions investigated for Al-1050, the local strain concentration at punch nose radius area was decreased by internal air-pressing of punch, and the deep drawing with internal air-pressing was proved to be very effective process for obtaining higher LDR.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2653-2663
• /
• 1994

The design of sheet metal working processes is based on the knowledge about the deformation mechanism and the influence of the process parameters. The typical geometric process parameters are the die geometry, the initial sheet thickness, the initial blank shape, and so on. The initial blank shape is of vital importance in the most sheet metal forming operations, especially in the deep drawing process, since the forming load and the strain distribution are significantly affected by the shape of an initial blank. The influence of the initial blank shape on a square cup deep drawing process is investigated by the numerical simulation and the experiment. The numerical simulation is carried out by a modified membrane finite element method which takes bending deformation into account. The numerical and experi-mental results show that the initial blank shape have strong influence on the forming load and the strain distribution. The numerical results are compared with the experimental results and other numerical results which are calculated with the membrane theory.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1129-1137
• /
• 1990

본 연구에서 사용된 유한요소 방정식은 국부 질점좌표계(natural convected coordinate system)를 이용하여 변형을 묘사하는 대변형을 고려한 탄소성 증분 수식을 사용하였고, 국부 질점 좌표계를 사용함으로써 변형도 성분이나 구성 방정식의 성분들 에 대한 좌표 변환 과정을 생략할 수 있다. 재료는 수직 이방성으로 가정하였다.

• 소성∙가공
• /
• 제8권1호
• /
• pp.14-21
• /
• 1999

Trapezoid cups and square ones have been deep-drawn to 45mm in depth. Displacements and strains have been analysed by FEM and experiment. Strains and effective strains in the corner flanges of trapezoid cups have been compared with those in square cups. The results have shown that because of shear strains on the corner flange, it is necessary to adopt effective strain for comparing strains, mean vale of effective strains in the corner flange with a corner angle of 72 degrees is narly equal to those with a corner angle of a right angle and mean value of effective strains with a corner angle of 102 degrees is smaller than those with a corner angle of a right angle.