• Journal of the Korean Geotechnical Society
• /
• v.31 no.10
• /
• pp.61-76
• /
• 2015

Recently, geotechnical engineering researches have been conducted on the Limit State Design (LSD) for deep and shallow foundations; however, there are very few studies on the retaining wall. As a basic study for the introduction of the LSD of a railway retaining wall, this study evaluates whether the reliability index satisfies the target reliability index for each failure mode in the standard drawing of the retaining wall. It also analyzes the feasibility of the LSD method by using the Load and Resistance Factor Design (LRFD) for the standard drawing of a retaining wall. In a portion of the standard drawing of the railway retaining wall, the reliability indices of the sliding and bearing capacity failure modes did not satisfy the target reliability index, and could not satisfy the limit state by the LRFD. Hence, the standard drawing of the railway retaining wall will need to be revised if the LSD is to be applied.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.629-637
• /
• 2013

In this study, a theoretical analysis method was suggested for predicting forming loads of continuous deep drawing and ironing processes (D.D.I. processes) by considering back tension and continuity equation, and FEA for D.D.I. processes was performed. Dimensions of a punch and a mold on the basis of design rules for a CNG storage vessel were applied for the analysis. To verify the suggested theoretical analysis, the results of theoretical analysis were compared with both those of FEA and experiments of previous studies. As the result of analysis, the values and tendencies of the loads predicted by the theoretical analysis were in agreement with those of FEA and the experiments. So, it is considered that the analysis suggested has reliability for predicting the forming loads of the continuous processes(deep drawing+ironing(1)+ironing(2)).

• Journal of Korea Society of Industrial Information Systems
• /
• v.26 no.5
• /
• pp.1-9
• /
• 2021

Children's drawings are widely used in the diagnosis of children's psychology as a means of expressing inner feelings. This paper proposes a children's drawings-based object detection algorithm applicable to children's psychology analysis. First, the sketch area from the picture was extracted and the data labeling process was also performed. Then, we trained and evaluated a Faster R-CNN based object detection model using the labeled datasets. Based on the detection results, information about the drawing's area, position, or color histogram is calculated to analyze primitive information about the drawings quickly and easily. The results of this paper show that Artificial Intelligence-based object detection algorithms were helpful in terms of psychological analysis using children's drawings.

• Communications of Mathematical Education
• /
• v.26 no.2
• /
• pp.177-203
• /
• 2012

The purpose of this research was to look at whether small group drawing activities can be applied to learning content that combine mathematics and art, by analyzing the changes in $10^{th}$ grade students' interests in mathematics and particular features of their strategic thinking that were reflected in small group drawing activities using graphs and inequations. The results of the study are as follows: 1. The small group drawing activity using graphs and inequations demonstrated that students interests in mathematics could experience positive changes. 2. The small group drawing activity using graphs and inequations was effective in stimulating the students' strategic thinking skills, which are higher level thinking activities necessary for creating problem solving. As the students went through the whole process of accomplishing a complete goal, the students engaged in integrated thinking activities that brought understandings of basic graphs and inequations together, and were also found to use such higher level thinking functions needed in achieving creative problem solving such as critical thinking, flexible thinking, development-oriented thinking, and inferential thinking. 3. The small group drawing activity using graphs and in equations could be expected to constitute learning content that integrate mathematics and art, and is an effective solution in boosting students' strengths in mathematics by way of activities that consider students' unique cognitive and qualitative peculiarities and through integration with art.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.10
• /
• pp.1043-1049
• /
• 2012

The FEM analysis of machine tools is the general analysis process to evaluate machine performance in the industry for a long time. Despite advances in FEM software, because of difficult simplicity of CAD drawing, little experience of joints stiffness modeling and troublesome manual contact area divide for bindings, the industry designers think the FEM analysis is still an area of FEM analysis expert. In this paper, the automation of modeling process with simplicity of drawing, modeling of joints and contact area divide is aimed at easy FEM analysis to enlarge utilization of a virtual machine tools. In order to verify the effects of modeling automation, a slant bed type model with tilting table is analyzed. The results show FEM modeling automation method only needed 45 minutes to complete the whole modeling process, while manual modeling method requires almost one month with 8200 calculations for coordinate transformations and stiffness data input.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.598-603
• /
• 2001

For metal forming analysis, upper-bound solution is practical method because the solution is overestimated. It is limited to determine stresses on tools by using upper-bound solution. In this study, new scheme to calculate stresses on tools based on upper bound solution is proposed. To verify the proposed scheme, plane strain drawing has been considered. The stresses on tools obtained by the proposed scheme are compared with results of rigid plastic FEM. And the stresses on tools have been determined by the proposed scheme in the forging within plane strain deformation.

• Transactions of Materials Processing
• /
• v.7 no.1
• /
• pp.3-11
• /
• 1998

During the forming process of sheet metals, the drawbead in the die face controls a restraining force so that the sheet flows into the die cavity with tension. In order to investigate a drawgbead restraining force and a pre-strain just after drawbeads which are essential in the finite element analysis of form-ing processes, the friction test and drawing test are employed. The experiments performed with a cir-cular bead stepped bead double circular bead and circular-and-stepped bead in the various forming conditions and bead sizes show that the restraining force varies linearly with the blank holding force. bead radius blank thickness and friction but the pre-strain nonlinearly does with them.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.24-30
• /
• 1999

In the automobile development, press tool design and manufacturing are very difficult and need high cost experienced workers. Therefore, we concerned ourselves in the cost down and easy manufacturing. In this research, we have developed a tool for LH/RH of the front fender, which had difficulty in forming. We have carried out the drawing analysis by Pam-stamp and CATIA modeling. Finally, we get the optimal design parameter. As a result of try out, we found out the optimal width and margin at the center line for tool design. Also, in order to get good results we have to intaglio margin in the part of the wheel house and utilize double bead on every side except corner.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.68-74
• /
• 2001

In the drawing of large size automotive panels, elastic deflection of die components is induced by the contact force between them. The deflection is nonuniform and locally distributed, and results in nonuniform material flow. In order to arrange such a nonuniform die gap, a correcting operation, so called die spotting, is inevitable, which requires trial and error works and consuming time. A prediction of the bending deflection prior to a try-out must be useful to reduce the die spotting time. In this study, drawing process of a front fender is simulated first. and the deflection of the blank holder is calculated from the contact force imposing on th blank holder. The balance block heights ensuring a uniform deflection are optimized by the analysis and design of experiments.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.06a
• /
• pp.163-172
• /
• 1994

The Aerospace and automobile industries have need to avoid sheet-metal forming problem such as incorrect springback after forming and trimming process, excessive thinning/tearing, wrinking/perkering. It is common practice to use costly trial-and-error experimental methods to develop tooling and manufacturing process parameters. Experimentation should be complemented with computer simulation to reduce cost and leadtime in manufacturing and to influence the design of components. In this study, firstly we solved the springback problem after drawing and trimming process of KFP(F100-229) engine airsealing bearing support part(53H00) forming and studied on the effect of several process parameters on the gap between the formed blank and punch shape using the implicit F.E.M code(ABAQUS). Secondly by the three dimensional dynamic analysis using the explicit. F. E. M code (LS-DYNA3D), we studied on the effect of several process parameters which can be used for avoid tearing and wrinking during the drawing process.