• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.6
• /
• pp.514-519
• /
• 2000

In order to develop the method for the calculation of flow resistance acting on cage net, the relation between the velocity reduction factor and $S_n/S$, the ratio of total area of netting projected to the perpendicular to the water flow $S_n$ to wall area of netting S, was derived based on the numerical and experimental analysis of the wake flow through a netting twine simplified by a cylinder and a netting panel. The velocity was reduced in accordance with the velocity reduction factor when the flow passed the netting panel upstream of a cage net. The proposed method for the calculation of fluid force acting on a square cage net was based upon the assumption that it could be divided into four side panels and one bottom panel. It was proved that the force could be calculated by the sum of the drag forces acting on the individual netting panels.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.9
• /
• pp.765-772
• /
• 2015

Aerodynamic force measurements and phase-locked PIV study were carried out to check the bio-mimetic MAV applicability of a swift flight. Two-rotational DOF robotic wing model and blowing-type wind tunnel were employed. The amplitude of twist angle were ${\pm}0$, ${\pm}5$, ${\pm}10$, and ${\pm}20$ deg. and stroke angles were manipulated by simple harmonic function with out-of-phase in regards to the stroke motion. It is acknowledged that the time-varying lift coefficients in accordance with the change of the twist angle did not result in any noticeable differences, just the small decrease and delay. However, the drag exhibited that the small change of the twist angle can produce large thrust. These findings imply why a swift uses small twist angle during flight. The PIV results displayed that the delay of aerodynamic forces is highly associated with the vortical structures around the wing. It is therefore indicated that a process of designing a swift-based Micro Air Vehicle should take the twist angle into consideration, as the essential parameter.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.6
• /
• pp.63-70
• /
• 2015

This paper proposes a novel airfoil named "KA2" for the blade of the wind turbine systems. Dynamic loads characteristics are analyzed and compared using aerodynamic data of ten airfoils including the proposed airfoil. The blade is divided into the sixteen elements in the longitudinal direction of the blade for applying the Blade Element Method Theory (BEMT) method, and in each element, torque, thrust, and pitching moment are calculated using turbulent time varying wind speed and aerodynamic data of each wing. Additionally, each force and torque is accumulated in the whole region of the blade for the estimation of representative values. The magnitude of such forces is comparatively analyzed for different airfoils. The angle of attack is constant below the rated wind speed due to the fact that the tip speed ratio is kept at the constant value, and it increases in the region of over rated wind speed as the tip speed ratio decreasing with constant rated rpm and increasing wind speed. Such increase in the angle of attack causes the changes of the force acting on the airfoil with different characteristics of lift and drag in the stall region of each different airfoil. Even though the mean wind speed is in the rated speed in a given time, because of the turbulence, it has either the over rated or under rated speed most of the time. Furthermore, the dynamic properties of each force are analyzed in this rated wind speed in order to objectively understand the dynamic properties of the blades which are designed based on the different airfoils. These dynamic properties are also compared by the standard deviation of time varying characteristics. Moreover, the output characteristics of the wind turbine are investigated with different airfoils and wind speeds. Based on these investigations, it was revealed that the proposed airfoil (KA2) is well applicable to the blade with passive pitch control system.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.2
• /
• pp.95-101
• /
• 2020

The wind turbine blades should be designed to possess a high stiffness and should be fabricated with a light and high strength material because they serve under extreme combination of lift and drag forces, converting kinetic energy of wind into shaft work. The goal of this study is to understand the basic knowledge required to curtail the process time consumed during the construction of small wind turbine blades using carbon fiber reinforced polymer (CFRP) prepeg composites. The configuration of turbine rotor was determined using the QBlade freeware program. The fluid dynamics module simulated the loads exerted by the wind of a specific speed, and the stress analysis module predicted the distributions of equivalent von Mises stress for representing the blade structures. It was suggested to modify the shape of test specimen from ASTM D638 to decrease the variance in measured tensile strengths. Then, a series of experiments were performed to confirm that the bladder compression molded CFRP prepreg can provide sufficient strength to small wind turbine blades and decrease the cure time simultaneously.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.4 s.77
• /
• pp.499-509
• /
• 2005

The excessive wind-induced motion of tall buildings most frequently result from vortex-shedding-induced across-wind oscillations. This form of excitation is most pronounced for relatively flexible, lightweight, and lightly damped high-rise buildings with constant cross-sections. This paper discusses the aerodynamic means ofmitigating the across-wind vortex shedding induced in such situations. Openings are added in both the drag and lift directions in the buildings to provide pressure equalization. Theytend to reduce the effectiveness of across-wind forces by reducing their magnitudes and disrupting their spatial correlation. The effects of buildings with several geometries of openings on aerodynamic excitations and displacement responses have been studied for high-rise buildings with square cross-sections and an aspect ratio of 8:1 in a wind tunnel. High-frequency force balance testshave been carried out at the Kumoh National University of Technology using rigid models with 24 kinds of opening shapes. The measured model's aerodynamic excitations and displacement were compared withthose of a square cylinder with no openings to estimate the effectiveness of openings for wind-induced oscillations. From these results, theopening shape, size, and location of buildings to reduce wind-induced vortex shedding and responses were pointed out.

• Journal of Korea Water Resources Association
• /
• v.56 no.9
• /
• pp.575-586
• /
• 2023

River vegetation has important functions such as providing a habitat for the river ecosystem and physical stability of the river bank. It also has adverse effects such as aggravating flood damages due to the increase in roughness coefficient and drag forces. River vegetation management is very important in finding a balance between flood and ecological management. There are still many uncertainties about the effect of vegetation on rivers. In this study, in order to analyze the effect of vegetated flow, the flow patterns according to the vegetation roughness are analyzed through a two-dimensional unsteady flow model for Chopyeong island of the Imjin River. According to the results of the 2D flow analysis using the HEC-RAS 2D model, the velocity distribution in the bend of the Imjin River was greatly affected by the vegetation roughness of Chopyeong Island. The formation of the main flow outside the bend of Chopyeong Island during flooding is presumed due to the influence of tree and grass on Chopyeong Island. If tree are distributed throughout Chopyeong Island, the velocity outside the bend is expected to be higher. River vegetation causes the effect of raising the water level, and could cause a change in the velocity distribution.