• Journal of the Korea Furniture Society
• /
• v.23 no.2
• /
• pp.214-221
• /
• 2012

Sustainable energy consumption and increasing $CO_2$ emissions stimulate Eco-friendly industry. Wood has positive various properties as alternative energy such as solar, wind and water. Wood provide lumber, pallet, paper, pulp and fuel through production process. Even Korea republic has 63.7% of forest rates, weather condition makes low forestry production capacity. For utilization of domestic small diameter log needs study mechanical properties. In this study, various properties tested on domestic Japanese Larch small diameter lumbers and make mechanical properties table for allowable stress calculation. Result of compressive test, allowable compressive stress is 13 MPa. Allowable bending stress is 12 MPa.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.104-108
• /
• 2002

Nail withdrawal tests were conducted on clear wood of domestic small diameter logs. Nails were driven into the cross and longitudinal sections of each specimen, then nail withdrawal tests were performed. Nail withdrawal loads are strongly dependent on the direction of nail positions. The average load values for the nail withdrawal both in cross section and longitudinal section are higher in high specific gravity (SG) wood of sawtooth oak (Quercus acutissima Carr.) than those in low SG wood of Korean red pine (Pinus densiflora Sieb. et Zucc.) and pitch pine (Pinus rigida Mill.). The average ratio of the nail withdrawal loads for side-grain and end-grain are higher in the low SG wood than that in the high SG of wood. Both linear and non-linear regression analyses were conducted on nail withdrawal load with SG, good correlations were obtained between nail withdrawal load and SG.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.59-65
• /
• 2002

EYM (European Yield Model), which was adopted in NDS (National Design Specification for wood construction), has been used in Korea without any verification of the analysis of bolted wood connections. In the case of applying lumber from domestic small diameter logs, however, there are some problems with the direct application of EYM ; 1) relatively low dowel bearing strength and dimensional stability due to a large amount of immature wood, 2) effect of MC (moisture contents) on the dowel bearing strength of wood and the yield load of a bolted connection. To evaluate the strength properties of bolted connections with lumber from domestic small diameter logs, effect of MC on the dowel bearing strength of wood was investigated and double shear bolted connection tests were performed. As the MC of wood increased, the dowel bearing strength was linearly reduced, even under 19% MC, which showed that adjustment, not considered in NDS, was required. Double shear bolted connection tests indicated that effect of MC on yield load should be considered in order to determine design value.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.301-308
• /
• 2014

Despite Korea forest take 63.7% of the nation's territory, productivity of domestic structural lumber is low. Studies of domestic small lumbers need to be improved domestic structural timber productivity. In this study, small diameter lumber and finger joint small diameter lumber took bending test to calculate MOE and MOR. MOE of small diameter lumber was $9.3kN/mm^2$ and MOE of finger joint small diameter lumber was $15.4kN/mm^2$. Allowable standard bending stress of small diameter lumber and finger joint small diameter lumber was calculated according to ASTM D 2915. Standard allowable bending stress of small diameter lumber was $12N/mm^2$ and standard allowable bending stress of finger joint small diameter lumber was $11N/mm^2$. Standard allowable bending stress of finger joint small diameter lumber should be considered to design structural beam members.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.3
• /
• pp.53-68
• /
• 1990

This research has been executed for maximization of lumber yield and more efficient use of small diameter logs. Sample logs from thinnings carne from densed artificial stands at the Kwangnung Experimental Forests situated in the central region of Korean peninsula. Species of sample logs were obtained to execute sawing and strength test for larch, and lumber strength test in full size for pitch pine and Korean pine. A survey on sawmills consuming domestic logs was carried out to know sawmill production, costs and utilization structure of lumber as a guide to business analysis. Results showed that sawing pattern from small logs less than 15cm in diameter was necessary to cut 9cm by 9cm square per one log in order to obtain high lumber recovery and provide for wide market needs. The total lumber yield of squares plus side boards was 56 percent to 58 percent from small logs and the yield for log sweep in 30 percent decreased by 24.5 percent in sawing production, compared to yield for straight logs. In sawing efficiency, production of lumber by twin band saw could be improved 238 percent higher than lumber of the same species produced by conventional sawmilling methods, and sawing accuracy with twin band saw was much higher at the lumber production than band saw. Lumber from the small larch logs has shown 70 knots per $m^2$ on its faces and also lumber showed lots of face checkings by air drying on the yard, compared to other species. MOR in bending of lumber in full size from small logs of larch was found ranging from 380kg/$cm^2$ to 460kg/$cm^2$, resulting in 40 percent less than the strength from clear small specimens. In lumber containing knots, cross grain, etc, longitudinal stress wave speed was delayed about 48 percent by defects in lumber from both larch and pitch pine logs. The surveyed sample sawmills consumed the domestic logs at the rate of 54 percent to 84 percent in the total timber consumption, showing high consumption at mills located in the mountains.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.4
• /
• pp.337-345
• /
• 2013

Log grading rules are essential tools to ensure the quality of logs in distribution structure. The rules should reflect the long experience and accepted usage practice in the market. A gap between the rules and market should be improved based on analysis of log qualities that produced and market demand. In this study more than ten millions logs which were produced by 5 Regional Forest Services in 2010~2011 period, were analyzed in their qualities including diameters and lengths by species. A proposal was driven to improve the current log grading rules in terms of log diameter classes and length. The followings are the summary of this study. Most of domestic softwood logs are belong to small diameter class of 100~160 mm, which imply the diameter classes of current log grading rules are immoderate. Distributions of log diameter shows distinctive patterns by species, which indicate a necessity of differentiated diameter classes by species in an improved rules. Lengths of logs in productions do not corresponding to the demands and preferences in sawmills. Therefore it is highly recommended to include log length term in an improved log grading system. Based on these findings, 6 log grading systems for 3 species groups of softwood are newly proposed to improve current log grading rules. Limits of log diameter and log length are also proposed for each log grading system.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.41-48
• /
• 1985

In near future about 500,000 hectares of Japanese larch and pitch pine need thinning to improve crop-tree spacing and reasonable species composition in Korea. Although thinned trees show very little high quality wood, in fact, all the sawed products are suitable for construction and farming materials. Studies on the utilization of thinned small-diameter trees have been implemented in order to increase lumber yield and display the skeleton of farm buildings. The results obtained in this study were summarized as follows: 1. According to Korean Conifers Log Grading System, log grade 3 was 87.4 percent in Japanese larch bolts and 95.8 percent in pitch pine bolts from thinned trees. The ability to identify defects was essential for grading logs. 2. Cutting diagrams of sawing were developed for 1-sided sawing, 2-sided sawing and 3-sided sawing by small end diameter class of bolt and cutting sizes also were found to use effectively lumber with wane. 3. Lumber recovery of Pitch pine was a little higher than that of Japanese larch. The maximum lumber yields of pitch pine by sawing patterns were 87.2 percent for 1-sided sawing, 80.8 percent for 2-sided sawing an 64.1 percent for 3-sided sawing, up yield compared with 58.1 percent for 4-sided sawing. The lumber yield of 1, 2 and 3-sided sawing significantly was higher value than that of 4-sided sawing. 4. Lumber was inspected and graded. Lumber quality of diameter class 12cm was a little better than that of diameter class 8cm, but 90 percent of lumber in diameter c1ass 16cm fell into grade 3. The lumber grade was classified by Korean standard grades of confiers lumber. 5. Lumber from 1, 2 and 3-sided sawing was used to build the skeleton of a farm house ($53m^2$) and greenhouse ($60m^2$) in order to display more efficient use of small diameter trees from thinning 6. Total volume of timber for building a farm house was $8.1m^3$ of imported timber. Timber of $7m^3$, 70 percent of total volume would be substituted imported timber for domestic timber.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.52-59
• /
• 2015

Cross-cut disks from small diameter oak logs were thermally modified and developed to make accessories such as a brooch. However it is known that domestic oaks are refractory and it is hard to dry their cross-cut disks without any drying defects. The cross-cut disks of Quercus variabilis (7 mm long in the longitudinal direction) were forced to dry in air at two different air velocities in summer and fall season, and their drying yields were investigated. Under the same condition, the average final moisture contents (MCs) of the specimens dried in the fall were lower than those dried in the summer. The average final MCs of the small diameter specimens dried at higher air velocity were slightly lower than those at lower air velocity while those of the large diameter specimen were not influenced by the air velocity. The number of the large diameter specimens with cross checkings was higher than that of the small diameter specimen. This discrepancy between two different diameters was twice in the fall, while it was more than four times in the summer. The large diameter specimens dried at low air velocity in Summer were cross-checked most, which was attributed to repeated water condensation and evaporation due to high humidity and low air velocity.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.7-14
• /
• 1996

두께가 20mm와 30mm이고 폭이 40mm와 60mm 인 길이 600mm의 낙엽송 제재목에 응력파 시험과 휨강도 시험을 실시하였다. 모든 시험편은 생재 상태로 구입 후 함수율 약 13%로 조습 처리하여 응력파 시험과 휨강도 시험을 시행하였다. 휨 영계수와 휨강도는 두께가 큰 것이 작게 나타났다. 최상의 상관관계는 휨 영계수와 양 표면에서 구한 값의 평균값을 사용한 응력파 속도 및 영계수 사이에 나타났다. 휨 영계수와 관계에서 응력파 영계수는 응역파 속도 보다 더 확연한 옹이의 영향을 보였다.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.3
• /
• pp.90-100
• /
• 1996

두께가 20mm 와 30mm 이고, 폭이 40mm 와 60mm인 600mm 길이의 낙엽송 제재목에 응력파 시험을 실시하였다. 모든 시험편은 생재 상태로 구입 후 함수율 27%, 22%, 17%과 12%조건으로 조습 처리하였다. 함수율 변화에 따른 응력파 속도와 영계수를 구하기 위한 응력파 시험을 4종류의 함수율 조건에서 실시하였다. 응력파 속도와 응력파 시험으로부터 구한 영계수는 시편의 함수율, 치수, 그리고 시험편의 옹이와 옹이 주변 목리의 상호작용에 의해 영향을 받았다. 모든 함수율 및 각 함수율 조건에서 응력파 속도는 응력파에 의해 구한 영계수와 양호한 상관관계를 나타냈다. 응력파 속도와 응력파 시험으로 구한 영계수는 함수율이 증가할 때 비선형적으로 감소하였으나, 함수율 25% 이상에서는 응력파에 의해 구한 영계수의 변화가 거의 없었다.