• 설비공학논문집
• /
• 제14권11호
• /
• pp.948-953
• /
• 2002

The electronic expansion valve (EEV) may be used to control the refrigerant flow rate for the multi-type heat pump. Stepping motor driven EEV may precisely control the refrigerant flow rate to meet each internal load requirement. To control the EEV, PI algorithm may be used. But the hysteresis of EEV deteriorates the performance of superheat control. To reduce the performance degradation, the PI algorithm along with the dither signal may be used. The dither signal, with about 10 times higher frequency than the system crossover frequency and about 10 times larger magnitude than the deadband of hysteresis, was selected for the superheat control of EEV. Experimental results showed the improvement of EEV control by adding the dither signal to the PI algorithm.

• 한국산학기술학회논문지
• /
• 제11권6호
• /
• pp.1949-1954
• /
• 2010

자이로스콥은 네비게이션을 가이드하거나 특성을 제어하는데 적절한 관성 측정도구로 사용되었다. 매우 민감 한 센서로서의 정확성은 저회전율 역전파 사이의 진동수 커플링으로 인한 폐쇄영역(데드 밴드)으로 결정된다. 이 진동 커플링은 위상차가 없으며, 각증분 값은 검출되지 않는다. 이 문제는 자이로스콥의 기계적인 진동으로 해결될 수 있다. 본 논문은 FEM을 통해 이론적 식들의 이론적 고려사항과 증명의 방법으로 기계 진동의 설계방법을 제시한 것 이다. 결과적으로, 공명 진동수와 최대 진동률의 최대 예측 오차는 5 %이하였다. 진동의 기계적 성능을 위한 이론식 들은 타당하다고 할 수 있다.

• 한국인터넷방송통신학회논문지
• /
• 제22권1호
• /
• pp.45-50
• /
• 2022

본 논문에서는 채널에서 발생되는 부호간 간섭을 줄이기 위한 적응 등화 알고리즘에서 dither 신호를 이용하는 DSE-MMA와 DQE-MMA 의 등화 성능을 비교하였다. 이들 알고리즘은 기존 MMA의 연산량을 줄이기 위하여 등장하였으며, 적응을 위한 오차 신호를 얻는 과정에서 dither 신호를 부가한 후 1 또는 N 비트의 양자화를 수행함으로서 양자화 오차 성분이 independent and identical 분포하도록 하여 적응 알고리즘의 robustness 성능을 개선할 수 있지만 정상 상태에서 MSE 성능이 열화된다. 논문에서는 동일한 채널과 신호대 잡음비에서 동일한 개념의 dithering에 의한 DSE-MMA와 DQE-MMA의 적응 등화 성능을 시뮬레이션을 통해 직접 비교하였다. 시뮬레이션 결과 DQE-MMA가 수렴 속도를 제외한 모든 성능 지수의 잔여량에서 DSE-MMA보다 우월함을 확인하였다.

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.107-111
• /
• 2013

The gyroscopes have been used as a suitable inertial instrument for the navigation guidance and attitude controls. The accuracy as very sensitive sensor is limited by the lock-in region (dead band) due to the frequency coupling between two counter-propagating waves at low rotation rates. This frequency coupling gives no phase difference, and an angular increment is not detected. This problem can be overcome by mechanically dithering the gyroscope. This paper presents the design method of mechanical dither by the theoretical considerations and the verification of the theoretical equations through FEM applications. As a result, comparing to the past result, the maximum prediction error of resonant frequency was within 3 percent and peak dither rate was within 5 percent. It was found that the theoretical equations can be feasible for the mechanical performance of dither.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1068-1073
• /
• 2005

Development of a locomotive mechanism for the capsule type endoscopes will largely enhance the ability to diagnose disease of digestive organs. In connection with it, most of the researches have focused on an installable locomotive mechanism in the capsule. In this paper, it is introduced that the movement of a capsule type endoscope in digestive organ can be manipulated by magnetic force produced outside human body. Since the magnetic force is provided by permanent magnets, no additional power supply to the capsule is required. Using a robotic manipulator for locating the external magnet, the capsule motion control system can cover the whole human digestive organs. This study is particularly concentrated on dither motion effect to improve the mobility of capsule type endoscope. It was experimentally found out that the friction coefficient between the capsule and digestive organ can be remarkably reduced by superposing yawing or rolling dither motion on the translatory motion. In this paper, the experimental results obtained while the direction, amplitude and frequency of sinusoidal dither motion were changed are reported.

• 한국군사과학기술학회지
• /
• 제17권4호
• /
• pp.531-536
• /
• 2014

There are trapping and stripping methods as the technique to remove the dither motion from RLG(Ring Laser Gyro) output. V/F converter output of angular sensor to measure the dither motion is used in stripping method. But bias and scale factor error is always included in V/F converter output and is a critical limiting factor for the wide application of stripping method to RLG. Therefore there have been many researches to solve this problem. The method to accurately estimate the bias and scale factor error of V/F converter using measurements of the angular sensor acquired at data sampling rate of INS is presented in this paper. To this end, stripping technique based on model of dither motion is newly applied.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.467-476
• /
• 2007

This work verifies the chaotic motion of a steer-by-wire vehicle dynamic system, and then elucidates an application of dither smoothing to control the chaos of a vehicle model. The largest Lyapunov exponent is estimated from the synchronization to identify periodic and chaotic motions. Then, a bifurcation diagram reveals complex nonlinear behaviors over a range of parameter values. Finally, a method for controlling a chaotic vehicle dynamic system is proposed. This method involves applying another external input, called a dither signal, to the system. The designed controller is demonstrated to work quite well for nonlinear systems in achieving robust stability and protecting the vehicle from slip or spin. Some simulation results are presented to establish the feasibility of the proposed method.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.57-63
• /
• 2005

Development of a locomotive mechanism fer the capsule type endoscopes will largely enhance the ability to diagnose disease of digestive organs. In connection with it, most of researches have focused on an installable locomotive mechanism in the capsule. In this paper, it is introduced that the movement of a capsule type endoscope in digestive organ can be manipulated by magnetic force produced outside human body. Since the magnetic force is provided by permanent magnets, no additional power supply to the capsule is required. Using a robotic manipulator for locating the external magnet, the capsule motion control system can cover the whole human digestive organs. This study is particularly concentrated on dither motion effect to improve the mobility of capsule type endoscope. It was experimentally found out that the friction coefficient between the capsule and digestive organ can be remarkably reduced by superposing yawing or rolling dither motion on the translatory motion. In this paper, the experimental results obtained with the direction, amplitude and frequency of sinusoidal dither motion changed is reported.

• Journal of Mechanical Science and Technology
• /
• 제16권4호
• /
• pp.485-491
• /
• 2002

The gyroscopes have been used as a suitable inertial instrument for the navigation guidance and attitude controls. The accuracy as very sensitive sensor is limited by the lock-in region (dead band) by the frequency coupling between two counter-propagating waves at low rotation rates. This frequency coupling gives no phase difference and an angular increment is not detected. This problem can be overcome by the mechanical dithering. The purpose of the mechanical dithering is to suppress the dead band, oscillate the monoblock about the rotation axis and add an external rotation rate. This paper presents the theoretical considerations of the mechanical performances of dither on the basis of the loading condition and angular characteristics due to the piezoelement deformation and the validity of theoretical equations are compared through FEM (Finite Element Method) simulations.

• 한국군사과학기술학회지
• /
• 제12권5호
• /
• pp.622-635
• /
• 2009

Laser Inertial Navigation System(LINS) consists of Ring Laser Gyroscopes(RLG) and accelerometers. RLG has a lock-in region in which there is zero output for input angular rates less than about 0.1deg/sec. The lock-in region is generated by the imperfect mirrors in RLG. To avoid the lock-in region, a sinusoidal motion called dither motion is applied on RLG. Therefore this dither motion is measured by RLG/accelerometer even if at a stop state. In this situation, the performance on the initial alignment of LINS can be degraded. In this paper, we analyze the performance on the initial alignment of LINS theoretically and experimentally. Analysis results include how dither motion, the pre-filter and the corner frequency in alignment loop affects the performance on the initial alignment of LINS.