• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2335-2347
• /
• 2023

As medical facilities are usually built at urban areas, special concrete aggregates and evaluation methods are needed to optimize the design of concrete walls by balancing density, thickness, material composition, cost, and other factors. Carbon treatment rooms require a high radiation shielding requirement, as the neutron yield from carbon therapy is much higher than the neutron yield of protons. In this case study, the maximum carbon energy is 430 MeV/u and the maximum current is 0.27 nA from a hybrid particle therapy system. Hospital or facility construction should consider this requirement to design a special heavy concrete. In this work, magnetite is adopted as the major aggregate. Density is determined mainly by the major aggregate content of magnetite, and a heavy concrete test block was constructed for structural tests. The compressive strength is 35.7 MPa. The density ranges from 3.65 g/cm³ to 4.14 g/cm³, and the iron mass content ranges from 53.78% to 60.38% from the 12 cored sample measurements. It was found that there is a linear relationship between density and iron content, and mixing impurities should be the major reason leading to the nonuniform element and density distribution. The effect of this nonuniformity on radiation shielding properties for a carbon treatment room is investigated by three groups of Monte Carlo simulations. Higher density dominates to reduce shielding thickness. However, a higher content of high-Z elements will weaken the shielding strength, especially at a lower dose rate threshold and vice versa. The weakened side effect of a high iron content on the shielding property is obvious at 2.5 µSv=h. Therefore, we should not blindly pursue high Z content in engineering. If the thickness is constrained to 2 m, then the density can be reduced to 3.3 g/cm³, which will save cost by reducing the magnetite composition with 50.44% iron content. If a higher density of 3.9 g/cm³ with 57.65% iron content is selected for construction, then the thickness of the wall can be reduced to 174.2 cm, which will save space for equipment installation.

• Journal of radiological science and technology
• /
• v.26 no.2
• /
• pp.37-42
• /
• 2003

Purpose : Computed tomographic equipment is essential for diagnosis by means of radiation. With passage of time and development of science computed tomographic was developed time and again and in future examination by means of this equipment is expected to increase. In this connection these authors measured rate of scatter ray generation at front of lead glass for patients within control room of computed tomographic equipment room and outside of entrance door for exit and entrance of patients and attempted to ind out method for minimizing exposure to scatter ray. Material and Method : From November 2001 twenty five units of computed tomographic equipments which were already installed and operation by 13 general hospitals and university hospitals in Seoul were subjected to this study. As condition of photographing those recommended by manufacturer for measuring exposure to sauter ray was use. At the time objects used DALI CT Radiation Dose Test Phantom fot Head (${\oint}16\;cm$ Plexglas) and Phantom for Stomache(${\oint}32\;cm$ Plexglas) were used. For measurement of scatter ray Reader (Radiation Monitor Controller Model 2026) and G-M Survey were used to Survey Meter of Radical Corporation, model $20{\times}5-1800$, Electrometer/Ion Chamber, S/N 21740. Spots for measurement of scatter ray included front of lead glass for patients within control room of computed tomographic equipment room which is place where most of work by gradiographic personnel are carried out and is outside of entrance door for exit and entrance of patients and their guardians and at spot 100 cm off from isocenter at the time of scanning the object. The results : Work environment within computed tomography room which was installed and under operation by each hospital showed considerable difference depending on circumstances of pertinent hospitals and status of scatter ray was as follows. 1) From isocenter of computed tomographic equipment to lead glass for patients within control room average distance was 377 cm. At that time scatter ray showed diverse distribution from spot where no presence was detected to spot where about 100 mR/week was detected. But it met requirement of weekly tolerance $2.58{\times}10^{-5}\;C/kg$(100 mR/week). 2) From isocenter of computed tomographic equipment to outside of entrance door where patients and their guardians exit and enter was 439 cm in average, At that time scatter ray showed diverse distribution from spot where almost no presence was detected to spot with different level but in most of cases it satisfied requirement of weekly tolerance of $2.58{\times}10^{-6}\;C/kg$(100 mR/week). 3) At the time of scanning object amount of scatter ray at spot with 100 cm distance from isocenter showed considerable difference depending on equipments. Conclusion : Use of computed tomographic equipment as one for generation of radiation for diagnosis is increasing daily. Compared to other general X-ray photographing field of diagnosis is very high but there is a high possibility of exposure to radiation and scatter ray. To be free from scatter ray at computed tomographic equipment room even by slight degree it is essential to secure sufficient space and more effort should be exerted for development of variety of skills to enable maximum photographic image at minimum cost.

• The Journal of Fisheries Business Administration
• /
• v.29 no.2
• /
• pp.77-96
• /
• 1998

Fisheries products in Korea generally go through three markets, namely the wholesale market at production site (Market A), the wholesale market at consumption site (Market B), and the retail market (Market C), from producers to end consumers. As the products move from Market A through Market B to Market C, the marginal gap of prices asked in these markets demonstrates an apparent relationship. The producers, middlemen, consumers, and governmental departments concerned may influence the marketing prices of fisheries products. This study employing the cointegration theory tries to investigate whether causality of the price-setting among these markets exists and, if any, what it is. The authors have focused their attention on fisheries markets in Pusan, analyzing the long-run equilibrium relationship and causality between the prices of hairtail and squid among markets at different levels. Data used in this study cover the period f개m August 1984 to December 1997 fer hairtail, and the period from May 1989 to December 1997 for squid. The main findings of the study may be summarized as follows: First, regardless of the price time-series of hairtail and squid in individual market, the first difference is necessary fur satisfying the stationary conditions since each time-series is a first integration. This means homogeneous integration of time-series, which is a requirement of the long-run equilibrium of prices at different markets, is satisfied. Second, the study of the long-run equilibrium relationship between the prices at Market A and Market B shows that a long-run equilibrium relationship does exist for selling prices of the two species at Market A and Market B. Third, the ECM (error correction model ) used here to describe the long- and short-run dynamics of price change demonstrates that, in the case of squid, the price change in Market A will lead to a corresponding price change in Market B in the long-run period. In the short-run, however, the price at Market H is not only influenced by the price change in Market A but influence the price at Market A as well, that is, the Prices between Market A and Market B have a feedback effect. It should be stressed that the limitation in data collection, which cover only two species of hairtail and squid, is likely to cause a sampling bias. Nonetheless, we may conclude that a dynamic relation in the formation of prices does exist in view of the transaction amount of species at different markets. It is believed that the conclusion drawn from this study would not only contribute to a long-lasted debate on the direction of causality of price-setting among academic circle and fishing community, but would provide a useful standard for the policy makers in charge of the price-setting of fisheries products as well.

• Journal of Nutrition and Health
• /
• v.45 no.6
• /
• pp.577-587
• /
• 2012

This study was conducted to investigate the consumption pattern and perception of traditional soy sauce and soybean paste products in male and female adults aged 19 and over in Seoul and Gyeonggi-do areas in order to promote the development of the products' industry. The survey was conducted between October 1 to October 15, 2011 among 294 male and female adults aged 19 years and over in Seoul and Gyeonggi-do areas. The gender distribution of the subjects was 33.3% males and 66.7% females. For a perception on traditional dietary life, the degree for enjoying meals with cooked rice as the staple food revealed that 32.3% of the subjects responded 'strongly agree'. The intake frequency of traditional soy sauce and soybean paste products in the subjects of the study showed that in the case of doenjang, 49.7% of the participants consumed it twice a week and 21.4% consumed it once a week. For gochujang, 59.9% consumed it twice a week and 19.0% consumed it once a week. The perception on the preparation method for traditional soy sauce and soybean paste products showed a low level for traditional soy sauce and soybean paste products. The reason for purchasing traditional foods showed that 77.6% of the subjects made purchases for convenience and 8.2% purchased it for its small package. For the subjects, the priority for purchasing traditional soy sauce and soybean paste products was as follows: in the first rank, ingredients & origin made up 33.7% and price comprised of 26.2% of the priority. Regarding satisfaction for soy sauce and soybean paste products in the market, the degree of satisfaction was high for gochujang. With regard to gender difference, female subjects showed a significantly lower satisfaction for cheonggukjang and kuk-ganjang, and a significantly higher satisfaction for chin-ganjang, compared to the male subjects. The results of the study depicted that consumer's requirement was high for traditional soy sauce and soybean paste products in the market, particularly for the safety of the products in the market. Consumer satisfaction was relatively positive yet, some efforts are needed in order to improve the quality of cheonggukjang and kuk-ganjang.

• Journal of KIISE:Databases
• /
• v.34 no.1
• /
• pp.1-17
• /
• 2007

As XML is becoming a de facto standard for distribution and sharing of information, the need for an efficient yet secure access of XML data has become very important. To enforce the fine-level granularity requirement, authorization models for regulating access to XML documents use XPath which is a standard for specifying parts of XML data and a suitable language for both query processing. An access control environment for XML documents and some techniques to deal with authorization priorities and conflict resolution issues are proposed. Despite this, relatively little work has been done to enforce access controls particularly for XML databases in the case of query access. Developing an efficient mechanism for XML databases to control query-based access is therefore the central theme of this paper. This work is a proposal for an efficient yet secure XML access control system. The basic idea utilized is that a user query interaction with only necessary access control rules is modified to an alternative form which is guaranteed to have no access violations using tree-aware metadata of XML schemes and set operators supported by XPath 2.0. The scheme can be applied to any XML database management system and has several advantages over other suggested schemes. These include implementation easiness, small execution time overhead, fine-grained controls, and safe and correct query modification. The experimental results clearly demonstrate the efficiency of the approach.

• Journal of Yeungnam Medical Science
• /
• v.5 no.1
• /
• pp.23-32
• /
• 1988

Finger injuries are becoming more common with the increasing use of mechanical industrial and household appliances. Among the hand injuries, amputation is the serious disaster to the patient. Recently, application of microsurgical technique to the reattachment of ampuatated digits has been common clinical procedures. We performed microsurgical replantation to the 75 patients with 102 digits from march in 1986 to february in 1988. The following results were obtained. 1. The most common age distribution was third decade and male to female ratio was about 5:1. 2. The ratio of right to left hand was about 1:1 but the dominant to non-dominant hand was about 2:1. 3. The index finger was most commonly injured and the next was middle finger. 4. The most common type of the injuries was the crushing injury and the most common vector was a kind of pressor. 5. The anesthesia was performed in equal ratio between the general and regional anesthesia. 6. The survival rate of microreplantation to the injuries of the zone II was 77.8% and zone III was 80%. 7. The functional result after replantation at zone II was better than zone III. 8. Microreplantation was performed in any case of the type of the injury, the severity of crushing and the ischemic time, and the patients requirement was an important factor.

• Journal of Nutrition and Health
• /
• v.42 no.4
• /
• pp.366-373
• /
• 2009

Codex Nutrient Reference Values (NRVs) were based on the 1988 Helsinki report and a single set of NRVs was established for the general population over 3 years for the purpose of food labeling in 1993. Dietary Reference Intakes (DRIs) with new concepts were developed in many countries recently. Hence there has been broad discussion regarding establishment of new NRVs using DRIs, which include estimated average requirement (EAR), recommended intake (RI or RDA), adequate intake (AI), and tolerable upper intake level (UL) in the world. This study was carried out to review various possible values for Codex NRVs such as population-weighted EAR, population-weighted RDA, and populationbased RDA. The values were simulated using DRIs and population distribution of Korea, USA, Japan, Philippines, Germany and England, and compared to the current Codex values and the highest RDA and the lowest UL among populations with different life-stage. Since population weighted/based values are necessary to be updated according to the population changes and are different across countries, inconsistency can be a serious barrier in international transactions. For some of nutrients such as vitamin A and zinc, values based on population-based RDA or the highest RDA were higher than the lowest UL. Therefore, careful considerations should be given before establishing Codex NRVs.

• Journal of Nutrition and Health
• /
• v.40 no.1
• /
• pp.78-88
• /
• 2007

The purpose of this study was to investigate dietary fat and individual fatty acids intake pattern of 174 college women living in Seoul and Gyong-gi province through internet nutritional assessment system. Each of the subjects was required to input their own food intake for three days, which included two days during the week and one day of the weekend, on the web program directly and all of the data collected were used for statistical analysis. The mean daily caloric intake of the subjects was 1,500.9 kcal which was at 71.5% of Estimated Energy Requirement (EER). Dietary fat contributed 27.6% of the total caloric intake which was slightly higher than the recommended limit of 25%. Daily cholesterol intake was 310.0 mg, which was also high to some degree. Mean daily N6 and N3 fatty acid intake was 6.1 g and 0.9 g, respectively, and calory % calculated from each were 3.63% and 0.53%. This result showed the intake of N3 fatty acid fell in Acceptable Macronutrient Distribution Ranges (AMR) $0.5\sim1.0%$ but that of N6 fatty acid was somewhat lower than the AMDR $4\sim8%$. N6/N3 ratio 8.5/l, however, was within the desirable range $4\sim10/1$. Considering overall dietary fatty acids intake, oleic acid was the most abundant, followed by linoleic and palmitic acid. And among polyunsaturated fatty acids intake, linoleic acid was exclusively high, accounting for 97.4% of total N6 fatty acid intake. On the contrary, three fatty acids, linolenic (67.3%), DHA (21.1%) and EPA (10.0%), together supplied 98.4% of total N3 fatty acid intake. Mean P/M/S was 0.9/l.1/1.0. The subjects' intake of fat, many fatty acids and cholesterol came from diverse food groups including meats, fats and oils, milk and milk products, eggs, fish, and soybean products. Nevertheless, the subjects tended to show unfavorable fat and fatty acids intake pattern in terms of quantity and quality. Based on these results, it is important to monitor dietary fat intake pattern of the general population continuously and an internet program such as the one used for this study would be valuable, especially for assessing dietary patterns in the younger generation.

• Journal of Chest Surgery
• /
• v.25 no.1
• /
• pp.1-16
• /
• 1992

The quantitatively measured local myocardial perfusion rates with microspheres are used as an objective indicator of even distribution of cardioplegic solution, and the efficacy of the retrograde right atrial route of cardioplegia is evaluated in hearts with various levels of coronary arterial obstruction. After initial antegrade cardioplegia under the median sternotomy and aortic cannulation, 60 hearts from anesthetized New Zealand white rabbits are divided in random order as normal group [ligated left main coronary artery ; MA, MR] and diagonal group [ligated proximal diagonal artery ; LA, LR]. Half of each group [N=10] are perfused with antegrade cardioplegia[A] under the pressure of 100 cmH2O and the other half with retrograde right atrial route[R] under the pressure of 60 cmH2O[St. Thomas cardioplegic solution mixed with measured amount of microspheres]. The myocardium is subdivided into segments as A[atria], RV[right ventricle]. S[septum], LV[normally perfused left ventricular free wall], ROI[ischemic myocardium of left ventricular free wall]. LV and RQI are further divided into N[subendocardium] and P[subepicardium]. The resulting local myocardial perfusion rates and N /P of each group are compared with Wilcoxon rank sum test. The weight of the hearts is 5.94$\pm$0.66g, and there are no statistically significant dif-ferences[p>0.05, ANOVA] between six compared group. The mean flow rate[F: ml /g / min] of MR group is comparable with MA group[p>0.05], but in N and L group, there are significantly depressed F with right atrial route of cardioplegia, which means elevated perfusion resistance with this route. In spite of no significant differences in delivered doses of microsphere[DEL] between compared groups[p>0.05, ANOVA], there are significantly depressed REC and NF in hearts with right atrial cardioplegia which suggests increased requirement of cardioplegic solution with this route. The interventricular septum shows poor perfusion with right atrial route of cardioplegia without obstruction of supplying coronary arteries. But, with obstruction of coronary artery supplying septum as in M group, the flow rate is superior with right atrial route of infusion. The left ventricular free wall perfusion rates of every RQI with R route are superior to that of A route[p<0.05]. But, in LV segments, there are unfavorable effects of right atrial cardioplegia in L group, although the subendocardial perfusion is well maintained in N group. The LV free wall of left main group shows depressed perfusion rates with antegrade route as compared with RQI segments of diagonal group. But, by contraries, there are increased perfusion rates and superior N /P ratio with retrograde right atrial route. It implies more effective perfusion with right atrial route of cardioplegia in more proximal coronary arterial obstruction[i.e., M group as compared with L group]. As a conclusion, all region of ischemia have superior perfusion rates with right atrial car-dioplegia as compared with antegrade route, and especially excellent results can be obtained in hearts with more proximal obstruction of coronary arteries which would otherwise result in more severe ischemic damage. But, the depressed perfusion rates of the segments with normal coronary artery in hearts with coronary arterial obstruction may be a problem of concern with right atrial cardioplegia and needs solution.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2008.05a
• /
• pp.47-70
• /
• 2008

Cost efficiency is today the primary requirement in the paper and board industry. This has led therefore, to a greater preponderance of products with specifically designed functionality to take account of current industry needs. Continually increasing machine coating speeds together with these new coating colour components have put more emphasis on the importance of the correct rheology and water retention of the coating colours to achieve good runnability and end product quality. In the coating process, some penetration of the aqueous phase, to the base paper or board must occur to anchor the pre-coating to the base or the topcoat to the pre-coat. The aqueous phase acts as a vehicle not only for the binder, but also for the other components. If this water or material penetration is not controlled, there will be excessive material shift from the coating colour to the base, before immobilization of the coating colour will stop this migration. This can result in poor machine runnability, unstable system and uneven coating layer, impacting print quality. The performance of rheology modifiers or thickeners on the coating color have tended to be evaluated by the term, "water retention". This simple term is not sufficient to explain their performance changes during coating. In this paper we are introducing a new concept of "material retention", which takes note of the total composition of the coating colour material and therefore goes beyond the concept of only water retention. Controlled material retention leads to a more uniform z-directional distribution of coating colour components. The changes that can be made to z-directional uniformity will have positive effects on print quality as measured by surface strength, ink setting properties, print gloss, mottling tendency. Optical properties, such as light scattering, whiteness and light fastness delivery should also be improved. Additionally, controlled material retention minimizes changes to the coating colour with time in re-circulation giving less fluctuation in quality in the machine direction since it more closely resembles fresh coating for longer periods. Use of the material retention concept enables paper and board producers to have more stable runnability (i.e. lower process costs), improved end product quality (i.e. better performance of used chemicals) and/or optimized use of coating colour components (i.e. lower total formulation cost)