• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.4
• /
• pp.603-610
• /
• 2004

Time delays are included in most of actual systems, and some of which are shown as time varying. To analyze the time varying time delay system in the time domain. a useful delay module to express the function as a tool is much helpful to get corresponding outputs under given conditions. A method is proposed here to design the algorithm of time delay module for simulation or control purposes, including the problems of initializing and reallocating data in buffer. After classifying the time varying time delay into the distributed mode and lumped mode, an object to describe delay module is configured and tested under the defined input signal and given time delay variation. The simulation results show that the output of module matches reasonably with the case of real system.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.657-659
• /
• 2004

CAN is a serial communication bus for real-time controls and automations in distributed control systems. In distributed control systems, occasionally a sensor module and a controller are not in the same node and physically separated. In order for the signal from a sensor node to reach the controller node, the signal must travel through network. CAN has a certain capabilities to deal with real-time data. However, when many nodes on the networks try to send data on the same network, the arbitration mechanism to solve the data collision problem is necessary. This situation causes the time delay which has detrimental effects on the performance of the control systems. This paper proposes a method to solve the problem due to the time delay in distributed control system using CAN. Time delay is approximated to an element with a rational transfer function using Pade approximation and Mu~synthesis method is applied. Since time delay in the network is not constant, the time delay element is considered to be an uncertainty block with a bound. The proposed method is applied to the experimental system with CAN and proved to be effective.

• ETRI Journal
• /
• v.28 no.1
• /
• pp.31-44
• /
• 2006

In a packet switching network, congestion is unavoidable and affects the quality of real-time traffic with such problems as delay and packet loss. Packet fair queuing (PFQ) algorithms are well-known solutions for quality-of-service (QoS) guarantee by packet scheduling. Our approach is different from previous algorithms in that it uses hardware time achieved by sampling a counter triggered by a periodic clock signal. This clock signal can be provided to all the modules of a routing system to get synchronization. In this architecture, a variant of the PFQ algorithm, called digitized delay queuing (DDQ), can be distributed on many line interface modules. We derive the delay bounds in a single processor system and in a distributed architecture. The definition of traffic contribution improves the simplicity of the mathematical models. The effect of different time between modules in a distributed architecture is the key idea for understanding the delay behavior of a routing system. The number of bins required for the DDQ algorithm is also derived to make the system configuration clear. The analytical models developed in this paper form the basis of improvement and application to a combined input and output queuing (CIOQ) router architecture for a higher speed QoS network.

• Journal of the Korean Society of Safety
• /
• v.18 no.3
• /
• pp.154-160
• /
• 2003

Uncertain time delay happens when the process reads the sensor data and sends the control input to the plant located at a remote site in distributed control system. As in the case of data network using TCP/IP, VDN that integrates both device network and data network has uncertain time delay. Uncertain time delay can cause degradation in performance and stability of distributed control system based on VDN. This paper first investigates the transmission characteristic of VDN and suggests a control scheme based on the Smith's predictor to minimize the effect of uncertain varying time delay. The validity of the proposed control scheme is demonstrated with real-time velocity control of DC servo motor located in remote site.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.7
• /
• pp.501-508
• /
• 2004

In this paper, a coordinated scheduling algorithm is proposed to reduce end-to-end delay in distributed control of systems. For the algorithm, the analysis of practical end-to-end delay in the worst case is performed priory with considering implementation of the systems. The end-to-end delay is composed of the delay caused by multi-task scheduling of operating systems, the delay caused by network communications, and the delay caused by asynchronous timing between operating systems and network communications. Through some simulation tests based on CAN(Controller Area Network), the proposed worst case end-to-end delay analysis is validated. Through the simulation tests, it is also shown that a real-time distributed control system designed to existing worst case delay cannot guarantee end-to-end time constraints. With the analysis, a coordinated scheduling algorithm is proposed here. The coordinated scheduling algorithm is focused on the reduction of the delay caused by asynchronous timing between operating systems and network communications. Online deadline assignment strategy is proposed for the scheduling. The performance enhancement of the distributed control systems by the scheduling algorithm is shown through simulation tests.

• International Journal of Safety
• /
• v.5 no.2
• /
• pp.6-11
• /
• 2006

The time delay in servo control on LonWorks/IP Virtual Device Network (VDN) is highly stochastic in nature. LonWorks/IP VDN induced time delay deteriorates the performance and stability of the real-time distributed control system and hinders an effective preventive and predictive maintenance. Especially in real-time distributed servo applications on the factory floor, timely response is essential for predictive and preventive maintenance. In order to guarantee the stability and performance of the system for effective preventive and predictive maintenance, LonWorks/IP VDN induced time delay needs to be predicted and compensated for. In this paper position control simulation of DC servo motor using Zero Phase Error Tracking Controller (ZPETC) as a feedforward controller, and Internal Model Controllers (IMC) based on Smith predictor with disturbance observer as a feedback controller is performed. The validity of the proposed control scheme is demonstrated by comparing the IMC based on Smith predictor with disturbance observer.

• Journal of the Korea Society for Simulation
• /
• v.5 no.1
• /
• pp.81-90
• /
• 1996

In this paper, we propose a new events ordering mechanism for the optimistic distributed simulation of DEVS models. To simulate DEVS models in a distributed environment, a synchronization protocol is required for correct simulation. Time Warp is the most well-known optimistic synchronization protocol for distributed simulation. However, employing the Time Warp protocol in distributed simulation of DEVS models incurs events ordering problem due to the semantic difference between Time Warp and DEVS, Thus, to resolve such semantic difference, we devise the time-and-priority-stamp and $\varepsilon$ -delay schemes. The proposed schemes can order simultaneous events correctly in Time Warp-based distributed simulation of DEVS models.Time Warp and DEVS, Thus, to resolve such semantic difference, we devise the time-and-priority-stamp and $\varepsilon$ -delay schemes. The proposed schemes can order simultaneous events correctly in Time Warp-based distributed simulation of DEVS models.

• Journal of the Korean Society of Safety
• /
• v.21 no.4 s.76
• /
• pp.25-32
• /
• 2006

LonWorks over IP(LonWorks-IP) virtual device network(VDN) is an integrated form of LonWorks device network and IP data network. In especially real-time distributed servo applications on the factory floor, timely response is essential for predictive and preventive maintenance. The time delay in servo control on LonWorks-IP based VDN has highly stochastic nature. LonWorks-IP based VDN induced transmission delay deteriorates the performance and stability of the real-time distributed control system and can't give an effective preventive and predictive maintenance. In order to guarantee the stability and performance of the system, and give an effective preventive and predictive maintenance, LonWorks-IP based VDN induced time-varying uncertain time delay needs to be predicted and compensated. In this paper new Pill control scheme based on Smith predictor, disturbance observer and band pass filter is proposed and tested through computer simulation about position control of DC servo motor. It is shown that how can the proposed control scheme be designed to minimize the effects of uncertain varying time delay and model uncertainties. The validity of the proposed control scheme is compared and demonstrated with the comparison of internal model controllers(IMC) based on Smith predictor with and without disturbance observer.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.2
• /
• pp.186-193
• /
• 2008

The Internet's low cost and ubiquity present an attractive option for real-time distributed control of processes on the factory floor. When integrated with the Internet, the LonWorks open control network can give ubiquitous accessibility with the distributed control nature of information on the factory floor. One of the most important points in real-time distributed control of processes is timely response. There are many processes on the factory floor that require timely response. However, the uncertain time delay inherent in the network makes it difficult to guarantee timely response in many cases. Especially, the transmission characteristics of the LonWorks/IP network show a highly stochastic nature. Therefore, the time delay problem has to be resolved to achieve high performance and quality of the real-time distributed control of the process in the LonWorks/IP Virtual Device Network (VDN). It should be properly predicted and compensated. In this paper, a new distributed control scheme that can compensate for the effects of the time delay in the network is proposed. It is based on the PID controller augmented with the Smith predictor and disturbance observer. Designing methods for output feedback filter and disturbance observer are also proposed. Tracking position control experiment of a geared DC Servo motor is performed using the proposed control method. The performance of the proposed controller is compared with that of the Internal Model Controller (IMC) with the Smith predictor. The result shows that the performance is improved and guaranteed by augmenting a PID controller with both the Smith predictor and disturbance observer under the stochastic time delay in the LonWorks/IP VDN.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.58-58
• /
• 2000

As many sensors and actuators are used in various automated systems, the application of network system to real-time distributed control is gaining acceptance in many industries. In order to take advantages of the network technique. however, network implementation should be carefully designed to satisfy real-time constraints and to consider network delays. This paper presents the implementation of feedback control system in Profibus-DP. Profibus-DP is a type of fieldbus protocols that are specifically designed to interconnect simple devices with fast I/O data exchange. As feedback control in profibus-DP is implemented, Network delays is found with influence of system performance. We analyze network delays in Profibus-DP into 3 reasons - dead time in Profibus interface, protocol delay, delay by asynchronization. In order to compensate the network delays, we introduce control algorithms with time delay concept. The results show that network delay can be compensated.