• Journal of Korea Water Resources Association
• /
• v.49 no.7
• /
• pp.579-588
• /
• 2016

Changes in precipitation due to climate change is made to induce the local and intensive rainfall, it is increasing damage caused by inland inundation. Therefore, it requires a technique for predicting damage caused by flooding. In this study, in order to determine whether this flood inundated by any route when the levee was destroyed, Which can simulate the path of the flood inundation model was developed for the SIMOD (Simplified Inundation MODel). Multi Direction Method (MDM) for differential distributing the adjacent cells by using the slope and Flat-Water Assumption (FWA)-If more than one level higher in the cell adjacent to the cell level is the lowest altitude that increases the water level is equal to the adjacent cells- were applied For the evaluation of the model by setting the flooding scenarios were estimated hourly range from the target area. SIMOD model can significantly reduce simulation time because they use a simple input data of topography (DEM) and inflow flood. Since it is possible to predict results within minutes, if you can only identify inflow flood through the runoff model or levee collapse model. Therefore, it could be used to establish an evacuation plan due to flooding, such as EAP (Emergency Action Plan).

• Journal of Korean Society for Quality Management
• /
• v.13 no.1
• /
• pp.77-83
• /
• 1985

This paper deals with a normality test to determine whether the data are sampled from normal population or not. In this paper the property that the mean and variance are independently distributed only for the normal distribution is used as a basis for developing a new test using the simple regression analysis. Considering the redan and variance of a random sample as independent and dependent variables, if it has not the regression relationship we conclude that the data were sampled from the normal distribution. The Monte-Carlo power study shows that the new test using the simple regression analysis has good power property relative to 6 well-known test methods for 11 distributions.

• Radiation Oncology Journal
• /
• v.21 no.2
• /
• pp.158-166
• /
• 2003

Purpose: To propose a conceptual design of a novel source for intensity modulated brachytherapy. Materials and Methods: The source design incorporates both radioactive and shielding materials (stainless steel or tungsten), to provide an asymmetric dose intensity in the azimuthal direction. The intensity modulated intravascular brachytherapy was performed by combining a series of dwell positions and times, distributed along the azimuthal coordinates. Two simple designs for the beta-emitting sources, with similar physical dimensions to a $^{90}Sr/Y$ Novoste Beat-Cath source, were considered in the dosimetric feasibility study. In the first design, the radioactive and materials each occupy half of the cylinder and in the second, the radioactive material occupies only a quater of the cylinder. The radial and azimuthal dose distributions around each source were calculated using the MCNP Monte Carlo code. Results: The preliminary hypothetical simulation and optimization results demonstrated the 87$\%$ difference between the maximum and minimum doses to the lumen wall, due to off-centering of the radiation source, could be reduced to less than 7$\%$ by optimizing the azimuthal dwell positions and times of the partially shielded intravascular brachytherapy sources. Conclusion: The novel brachytherapy source design, and conceptual source delivery system, proposed in this study show promising dosimetric characteristics for the realization of intensity modulated brachytherapy in intravascular treatment. Further development of this concept will center on building a delivery system that can precisely control the angular motion of a radiation source in a small-diameter catheter.

• Journal of the Korean Society of Radiology
• /
• v.10 no.7
• /
• pp.483-487
• /
• 2016

The purpose of this study is to investigate whether gold nanoparticles had radiosensitization when combined with gamma and x ray beam. Cytotoxicity was mearsured with comparing survival fraction after incubated time 6,12,18 and 24 hours. Clonogenic assay was employed to assess survival fraction of cells with and without gold nanoparticles treatment following gamma ray irradiation. The most of gold nanoparticles were distributed in the cytoplasm. And the toxicity of gold nanoparticles used this study were found to be non-cytotoxic. And we also observed enhancement by about 40% in RBE value for gamma ray irradiation of cells treated with gold nanoparticles. Dose reduction of about half for gamma ray irradiation is demonstrated for gold nanoparticles treated cells as compared to untreated cells. In cells with exposed to gamma ray, DNA damage was increased when compared to only radiation exposed cells. The study revealed a significant reduction in radiation dose for killing the cells with internalized gold nanoparticles as compared to the cells without gold nanoparticles. The gold nanoparticles treatment resulted in enhancement of radiation effect as evident from increase in relative biological effectiveness values for photon irradiated cells.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.5
• /
• pp.619-628
• /
• 2009

LiDAR has capability of rapid data acquisition and provides useful information for reconstructing surface of the Earth. However, Extracting information from LiDAR data is not easy task because LiDAR data consist of irregularly distributed point clouds of 3D coordinates and lack of semantic and visual information. This thesis proposed methods for automatic extraction of buildings and 3D detail modeling using airborne LiDAR data. As for preprocessing, noise and unnecessary data were removed by iterative surface fitting and then classification of ground and non-ground data was performed by analyzing histogram. Footprints of the buildings were extracted by tracing points on the building boundaries. The refined footprints were obtained by regularization based on the building hypothesis. The accuracy of building footprints were evaluated by comparing with 1:1,000 digital vector maps. The horizontal RMSE was 0.56m for test areas. Finally, a method of 3D modeling of roof superstructure was developed. Statistical and geometric information of the LiDAR data on building roof were analyzed to segment data and to determine roof shape. The superstructures on the roof were modeled by 3D analytical functions that were derived by least square method. The accuracy of the 3D modeling was estimated using simulation data. The RMSEs were 0.91m, 1.43m, 1.85m and 1.97m for flat, sloped, arch and dome shapes, respectively. The methods developed in study show that the automation of 3D building modeling process was effectively performed.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.3
• /
• pp.188-196
• /
• 2009

This study conducted numerical simulations to analyze the wave characteristics(distribution) depending on the directional changes of waves in the Nakdong river estuary by using SWAN(Simulating WAves Nearshore) model. The results from the tests are summarized as below. The wave height rates are generally highly distributed with the incident waves from the S, SSE, SSW, SE, SW in sequence. When the waves from the S, SSW, SSE directions are predominant, the bigger waves were observed in front of sandbars. According to the results of the wave steepness against the wave direction, at the east coast of Gadeok island(northwest of Nakdong estuary), where has mild seabed slopes, the wave height rates distribute in the range of 0.4~0.6; the wave height rates over the west coastal region of Dadeapo(southeast of Nakdong estuary) are 0.5~0.6. The wave height rate tends to be rapidly decreased over the east region of Nakdong river estuary rather than its west region.

• Korean Journal of Environmental Agriculture
• /
• v.12 no.3
• /
• pp.209-218
• /
• 1993

The behaviour of insectcide ethoprophos (O-ethyl S,S-propyl phosphorodithioate) in soil was investigated. In a laboratory study, the degradation of ethoprophos in soil followed first-order reaction kinetics. The half-life of the insecticide in the soil incubated with 10, 18 and $25^{\circ}C$ was 12.4, 5.5 and 2.5 days, respectively. Arrhenius activation energy was 73.8 KJ/mole. The half-life was 46.4, 17.6 and 6.9 day in the soil with 7, 14 and 19% of soil water content, respectively. The moisture dependence B value in empirical equation was 1.67. The adsorption isotherm for ethoprophos in the soil agreed with freundlich equation. The adsorption distribution coefficient (Kd) was 0.27. In a field study prepared in autumn with undisturbed soil column in a mini-lysimeter system, ethoprophos residues were largely distributed in the top $0{\sim}2cm$ soil layer and moved down to the top 6cm soil layer. Persistence of ethoprophos in field soil was correlated with variation in weather pattern during the period of experiments. The half-life of ethoprophos treated at March and October was about 17 and 5 days, respectively. The ethoprophos woil was degraded up to 90% at 37day after the both treatment. In persistence and mobility of ethoprophos in field soil, the observed data were reasonably corresponded with predicted data by some computer model of pesticide behaviour.

• Journal of Energy Engineering
• /
• v.2 no.1
• /
• pp.123-132
• /
• 1993

This work is focussed on the reduction of ethanol separation energy from alcohol fermented broth and categorized into the development of a computer program for the design of the pressurized/depressurized distillation process which has been regarded as one of the energy-reducing models for the conventional distillation process, the optimization of operating conditions of distillation towers by means of the developed program, and the evaluation of the total annual energy cost of pressurized/depressurized distillation columns compared with that of the conventional single distillation columns. The operating pressures are, in case of pressurized/depressurized distillation, 3103/760 mmHg, 3103/450 mmHg, 3103/160 mmHg, and in case of conventional distillation, 760 mmHg. The optimum reflex rations which the sum of the annual energy cost and the annual fixed cost for each process becomes minimum are 3.7475/2.9111 for the operating pressures of 3103/760 mmHg, 3.814/2.9712 for 3103/450 mmHg, 3.0783/2.2400 for 3103/150 mmHg, and 3.8544 for the atmospheric operating pressure. And the annual energy cost of pressurized/depressurized distillation process for the above-mentioned operating pressures is distributed between 42% and 47% of that of conventional distillation process.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1A
• /
• pp.90-95
• /
• 2000

In the Ordered Core Based Tree(OCBT) protocol, a core location is the most important feature to affect the performance. In this paper, the location placement of multiple level cores is studied. The proposed algorithm isthat each node in the network evaluates a sum of shortest path costs from all the other nodes and the entirenetwork is divided into a hierarchy region to have 3-logical level(Small, Medium, Large). The node to have thelowest cost in each S-Region is decided to be a core node. Then, the core nodes in the each S-Region evaluatea sum of shortest path costs from all the other core nodes in the same M-Region. The core node to have thelowest cost is decided to be the upper level core node. Similarly the highest level core node is decided in theL-Region. The proposed algoritthm is compared with conventional two methods to put the core nodes in thenetwork One is the random method to put the core nodes randomly. The other is the center method to locatethe core node at the nearest node from the center of each S-Region and then to locate the highest level corenode at the nearest core node from the center of the entire network. Extensive simulations are performed in theview of mean tree cost and join latency. Simulation results show that the proposed algorithm has betterperformance than random method or center method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.6C
• /
• pp.495-505
• /
• 2010

In this paper, the effect of Near-Far Problem (NFP) among distributed nodes in OFDMA-based Wireless Mesh Networks (WMNs) is analyzed by investigating statistical characteristics of Time Difference of Arrival (TDoA) and Desired-to-Undesired power Ratio (DUR). In order to overcome the effects of Inter-Symbol Interference (ISI), Inter-Carrier Interference (ICI), and Inter Link Interference (ILI), caused by TDoA in WMNs, we derive effective SINR for each subcarrier, and then, propose the optimal starting point of FFT window which can minimize BER for each subcarrier. In addition, we propose a subcarrier-based Zero Forcing - 2 Dimensional Ordered Successive Interference Cancellation (ZF-2DOSIC) technique for signal detection in WMNs with TDoA. It is verified by simulation that the effective SINR and uncoded BER performances of the proposed signal detection technique for OFDMA-based WMNs are significantly improved, compared with those of conventional technique.