• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.265-271
• /
• 2023

Recently, location information services are gradually expanding due to the development of information and communication technology. RSSI is widely used to extract indoor and outdoor locations. The indoor and outdoor location estimation methods using RSSI are less accurate due to the influence of radio wave paths, interference, and surrounding wireless devices. In order to improve this problem, a distance estimation method that takes into account the wireless propagation environment is necessary. Therefore, in this study, we propose a distance estimation algorithm that takes into account the radio wave environment. The proposed method estimates the distance by learning RSSI input and output considering the RBF neural network and the propagation environment. To evaluate the performance of the proposed method, the performance of estimating the location of the receiver within a range of up to 55[m] using a BLE beacon transmitter and receiver was compared with the average filter and Kalman filter. As a result, the distance estimation accuracy of the proposed method was 6.7 times higher than that of the average filter and Kalman filter. As shown in the results of this performance evaluation, if the method of this study is applied to location services, more accurate location estimation will be possible.

• Imaging Science in Dentistry
• /
• v.54 no.2
• /
• pp.121-127
• /
• 2024

Purpose: Preoperative identification of the intraosseous posterior superior alveolar artery (PSAA) is critical when planning sinus surgery. This study was conducted to determine the distance between the cementoenamel junction and the PSAA, as well as to identify factors influencing the detection of the PSAA on cone-beam computed tomography (CBCT). Materials and Methods: In total, 254 CBCT scans of maxillary sinuses, acquired with 2 different scanners, were examined to identify the PSAA. The distance from the cementoenamel junction (CEJ) to the PSAA was recorded at each maxillary posterior tooth position. Binomial logistic regression and multiple linear regression were employed to evaluate the effects of scanner type, CBCT parameters, sex, and age on PSAA detection and CEJ-PSAA distance, respectively. P-values less than 0.05 were considered to indicate statistical significance. Results: The mean CEJ-PSAA distances at the second molar, first molar, second premolar, and first premolar positions were 17.0±4.0 mm, 21.8±4.1 mm, 19.5±4.7 mm, and 19.9±4.9 mm for scanner 1, respectively, and 17.3±3.5 mm, 16.9±4.3 mm, 18.5±4.1 mm, and 18.4±4.3 mm for scanner 2. No independent variable significantly influenced PSAA detection. However, tooth position (b=-0.67, P<0.05) and scanner type (b=-1.3, P<0.05) were significant predictors of CEJ-PSAA distance. Conclusion: CBCT-based estimates of CEJ-PSAA distance were comparable to those obtained in previous studies involving cadavers, CT, and CBCT. The type of CBCT scanner may slightly influence this measurement. No independent variable significantly impacted PSAA detection.

• Journal of Korean Port Research
• /
• v.14 no.3
• /
• pp.341-351
• /
• 2000

This study is on the purpose that the influence caused by noise and shaking through construction works shall be ranged to the fishing species of fishing area of the surface of sea. This study have been performed through analysis of physical effect by the value of noise and shaking test. The resulted purpose of this study has been carried out regarding whether influence factor of the fishing species and others are related or not as per the noise and shaking. For the purpose of the survey of noise and shaking, observances have been performed regarding the direct water surface of fishing area are as well as undersea. As for this result, the influence area for the injury at the fishing area caused by the noise and shaking have been stretched out to the distance of 10km from the source of sound. In this conclusion, this study is regarded as the reference basis of the compensation of injury for the species of fish and others in fishing area.

• Journal of Korea Game Society
• /
• v.21 no.3
• /
• pp.107-116
• /
• 2021

Full-board position evaluation in Go is a measurement of judging the advantages and disadvantages between black and white players during a game playing, and through this, the proper tactics and strategies would be undertaken in the near future. In this paper, we tried to evaluate the full-board positions of the 50 AlphaGo vs AlphaGo games using influence function that halved according to the distance. According to the experimental results, there is a limit to making accurate evaluation when the full-board position is assessed only by influence function. In order to overcome this, it is necessary to solve life-and-death problems to deal with dead stones, and it showed that if this is reinforced, we can precisely evaluate the full-board position in Go.

• Water Engineering Research
• /
• v.1 no.2
• /
• pp.159-168
• /
• 2000

In this paper, the increment of the local scour depth at piers by constructing the bridge between existing bridges is examined through the experiments in which 5 piers in the non-cohesive bed material in the experimental flume were installed. In the experiments the maximum distance of 25 times of the pier length and the maximum distortion width of 8 times of the pier width were utilized. Through the experimental studies, it was indicated that low flow, which can be characterized as the flow having low Froude numbers, the maximum bed configuration change is obtained when the piers are installed in the straight line in the flor direction without any distortion. However, In the high flow, which can be characterized as the flow having high Froude numbers, the maximum bed configuration change is obtained when the piers are installed with some distortion from the flow direction. The influence of the bed configuration by interaction between bridge piers is changed depending upon the Froude numbers, the distance between piers, and the distortion width between adjacent bridge piers. Also, because the scour patterns are affected by the bed configuration, the maximum scour should be increased by about 60% compared to that in a single pier if the interaction between bridge piers exists. It can be suggested that the maximum scour depth at bridge piers predicted by applying the existing equations should be increased if the interaction between bridge piers exist. Those cases are found when new bridges are constructed successively in the river in the urban area.

• Journal of the Korean Society of Safety
• /
• v.28 no.6
• /
• pp.84-89
• /
• 2013

The main causes of traffic accidents can be classified by 3 factors - human error, vehicle deficiency and road environmental problem and most accidents occurs not only 1 factor but combination of 2 or 3-factors. Among these factors, road environmental factor is the most important factor due to influence the behavior of cars and road users and road environmental factor affects 30% of total accidents approximately. The 5 years traffic accidents data analyzed to verify the accidents severity on Korea National Highways. In order to analyze the severity, Ordered Probit Model was used. As a independent variables of this model the number of lane, neighbor road environments, sight distance, vertical grade, lane width, shoulder width and traffic volume were used and as a dependent variables the minor injuries, serious injuries and fatalities were used. Research results shows that sight distance and lane width are identified as significant factors for the traffic accident severity and lesser sight distance and lane width shows greater traffic accident severity.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.123-128
• /
• 2009

The effects of temperature and initial crack length on the impact fracture behavior for the side plate material of FRP ship were investigated. And the effects of the counterpart roughness and sliding distance on the volumetric wear of same material were investigated as well. Impact fracture toughness of GF/PE composites displayed maximum value when the temperature of specimen is room temperature and $50^{\circ}C$, and with decreasing the temperature of specimen, impact fracture toughness decreased. Impact fracture energy of GF/EP composites decreased with increasing the initial crack length of specimen, and this value decreased rapidly when the temperature of specimen is lowest, $-25^{\circ}C$. It is believed that sensitivity of notch on impact fracture energy were increased with decreasing the temperature of specimen. With increasing the sliding distance, the transition sliding distance, which displayed different aspect on the friction coefficient and the volumetric wear loss, were found out. Counterpart roughness had a big influence on the wear rate at running in period, however the effect of counterpart roughness became smaller with sliding speed increase in. Volumetric wear loss were increased with increasing the applied load and the counterpart roughness.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.6
• /
• pp.216-223
• /
• 1995

This research is aimed to investigate the influence of the structural parameters on dowel action of reinforcing bars in reinforced concrete members. I~ollowing the previous research, $^{(3.6)}$ a total of forty two specimens were tested to scrutinize the dowel action of reinforcing bars. Concrete cover, reinforcing bar size and bar distance were taken as main test variables for constant compressive strength of concrete. ]+om the test results, the structural behavior of all specimens was almost linear up to failure load. It is seen that dowel force increases as concrete cover increases. Reinforcing bar size and bar distance hardly affects dowel force. It is found that the dowel forces obtained by this experimental research is relatively close to that of regression analysis results and White's equation.

• Journal of the Korean Society for Precision Engineering
• /
• v.4 no.4
• /
• pp.84-92
• /
• 1987

To investigate the influence of the cutting pressure on the laser cutting quality, an expermental facility was constructed which can measure the cutting pressure distribution for various cutting conditions. Flow visualization was performed using the Schlieren photography and the pressure acting on the workpiece surface was measured, corresponding to the important process variables such as the kind of assist gas, nozzle pressure, distance between the nozzle exit and the workpiece surface, and the presence of the secondary nozzle. The cutting pressure acting on the workpiece was largely influenced by the nozzle pressure and nozzle-workpiece distance. The secondary nozzle which is used to raise the effective working pressure had its obvious role only when the angle between it and the main nozzle was small and when the distance between the nozzle exit and the workpiece surface was large.

• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.44-49
• /
• 2008

In this research, I would like to choose sliding distance and ventilated hole number which affect to the amount of wear of disk and pad as experiment conditions of 'the amount of wear' through wear test of motorcycle brake disk. Also, I analyze the amount of wear according to the variation of coefficient of friction by using design of experiment that is being widely used in diverse areas. With the tests of least, I present the correlation of each experiment condition. Therefore, I analyzed the variation of the amount of wear of disk and pad according to test factors such as ventilated hole number, applied load, sliding speed, and sliding distance in wear test of motorcycle brake disk by applying the design of experiment. Also, I analyzed quantitatively the influence of test factors through Taguchi Robust experimental design, response surface and examined the most suitable level and estimation of the amount of wear of disk. From these, I reached the following conclusions. response surface design, mathematical model was constructed about amount of wear of disk and pad. The amount of wear that decrease according to increase of ventilated hole number, and it's increase according to Increase of applied load, sliding speed, and sliding distance.