• 한국화재소방학회논문지
• /
• 제18권2호
• /
• pp.7-11
• /
• 2004

본 논문에서는 비닐 캡타이어 전선(600 V, VCTFK, $2C{\times}1.25mm^2$)을 모델로 하여 과전류 시 전류크기 및 이격 거리에 따른 전선 상호간의 힘을 유한요소법(FEM)을 통하여 계산하며, 또한 직접 제작한 대전류 공급 장치(형명: EHT_EFAD, Korea 사용하여 과전류시 전류크기와 공급시간에 따른 전선 상호간의 최대 이격거리에 대하여 실험함으로써 과전류로 인한 전기화재 감식 시 기초 자료로 활용하고자 한다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권3호
• /
• pp.9-12
• /
• 2012

Usually, the AC loss from the superconducting element of an SFCL due to the load current is very small because it is composed of the combination of bifilar windings with very small reactance. Although the AC loss is small enough, we should be albe to predict for the design and control of the cryogenic system. In fact, an SFCL for the transmission voltage class may not generate ignorable AC loss because of the inevitable space between the HTS wires for the high voltage insulation and cryogenic efficiency. To measure the AC loss dependency on the space between the 2G HTS wires with the width of 4.4 mm, we prepared an experimental setup which could adjust the distance between the wires. We used two 500-mm length HTS wires in parallel and applied the current in the opposite direction for each wire to simulate a part of a current limiting module for a high voltage SFCL. We also put two couples of voltage taps at the ends of each wire and a cancel coil in the voltage measurement circuit to compensate the reactive component from the voltage taps. In this condition, we varied the distance between the wires to investigate the change of the transport current loss. A similar experimental study with HTS wire with the width of 12 mm is now in progress.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권1호
• /
• pp.22-26
• /
• 2007

Superconductor is weak in AC condition. Bifilar geometry provides a solution to reduce AC loss. Bifialr geometry is piled up or wound with more than two layers. When a layer of superconductor abuts on other layers, AC loss is affected by not only self-field, but also magnetic field induced by adjacent layers. In this study, two superconductors are piled up as a series connection so that current flows in different directions. By this method, magnetic field is cancelled. If magnetic field is cancelled, AC loss is reduced. To compare AC loss with respect to piling method, we measured the AC loss difference between the case facing each other with substrate side and the case facing with YBCO side. Measured AC loss is compared with one-way current flow single layer AC loss. In addition, we analyzed how much AC loss was increased, or reduced. All results were compared with those calculated with Norris equation. By this experiment, we concluded that distance between two wires is the important cause of AC loss. The distance between two wires affects magnetic field reduction in YBCO and induced current flow on substrate side.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.49-55
• /
• 2012

The tandem welding process is one of the most efficient welding processes widely used in material joining technique such as manufacturing of strong and durable structures. It facilitates high rate of joint filling with little increase in the overall rate of heat input due to the simultaneous deposition from two electrode wires. The two electrodes in tandem welding process helps in high-efficiency and high productive of welding process. In this study a automated tandem welding system is developed to determine the correlation between cathode and anode and compared with current ratio of the two electrode torch. Three different inter-electrode distances were chosen, 25mm, 35mm and 45mm to perform the experiment with three different current ratio. From the experiment results, the current ratio between two torch has a large impact on width, height and depth of penetration. In addition, a stable bead geometry is obtained when inter-electrode distance is 35mm.

• 한국초전도ㆍ저온공학회논문지
• /
• 제13권1호
• /
• pp.41-45
• /
• 2011

Hybrid fault current limiters (FCL) have been researched at Yonsei University. The hybrid FCL has advantages such as having a rapid response to a sudden fault situation and a fast recovery time from a quench. It consists of an asymmetric HTS coil, a switching module, and a bypass reactor. The asymmetric HTS coil is wound with two different types of HTS wires in an opposite direction so that it has nearly zero inductance at the superconducting state. When the quench occurs at the fault state, a strong magnetic field is generated from the asymmetric coil because of different quench characteristics of two HTS wires, and then a repulsive force is induced in the switching module. The force opens the switch and the fault current is pushed into the bypass reactor. In this research, we analyzed the cause of the repulsive force and confirmed, experimentally and computationally, that the magnitude of a repulsive force is varied by changing the gap distance between the asymmetric coil and the switching module. By using the FEM simulation, we calculated the repulsive force with respect to the gap distance and verified that the effect of the gap distance. Then, short circuit test was carried out to confirm the correct operation of the fast switch.

• Journal of the Korean Wood Science and Technology
• /
• 제14권1호
• /
• pp.3-44
• /
• 1986

목재(木材)파아티클과 성질(性質)이 전혀 다른 철선(鐵線)을 물리적(物理的)으로 결합(結合)시킴으로써 목재(木材)와 철재(鐵材)의 재료적(材料的) 특성(特性)을 서로 보완(補完)하여 목재(木材)파아티클과 철선(鐵線)의 새로운 복합체(複合體)인 목질(木質)-철선(鐵線)보오드를 제조(製造)하고 그 특성(特性)을 구명(究明)하여 기초자료(基礎資料)를 얻고자 하였다. 메란티 합판제조폐재(合板製造廢材)을 이용(利用)한 팔만칩을 12mesh를 통과하고 20mesh체에 남는 큰 파아티클과 20mesh을 통과하고 60mesh체에 남는 작은 파아티클로 구분하여 요소수지를 분무한 다음, 굵기 1mm인 철선(鐵線)을 나비방향과 길이방향으로 1, 2 및 3층(層)으로 배열하여 성형(成型)하고 시험용(試驗用) 복합(複合) 파아티클 보오드를 제조하였다. 1층(層) 철선구성(鐵線構成)보오드의 경우에는 철선간(鐵線間)의 배치간격(配置間隔)을 나비방향과 길이방향(方向)으로 각기 0.5cm, 1cm, 1.5cm, 2cm 및 2.5cm 등(等) 5가지로 하여 24가지의 철선구성방법(鐵線構成方法)으로 하였으며, 2층(層) 철선구성(鐵線構成 )보오드는 철선구성간격(鐵線構成間隔)을 1cm로 하였고 철선구성방법(鐵線構成方法)을 3가지로 하였으며, 3층(層) 철선구성(鐵線構成)보오드는 철선구성간격(鐵線構成間隔)을 1cm로 하고 철선구성방법(鐵線構成方法)을 11가지로 하여 제조(製造)한 보오드는 대조(對照)보오드를 포함(包含)하여 312개였다. 보오드를 성형(成型)한 열압온도(熱壓溫度) 160$^{\circ}C$, 악력(壓力) 35kgf/$cm^2$, 열압시간(熱壓時間) 9분(分)으로 하여 보오드를 제조(製造)하고 이 목질(木質) 철선복합(鐵線複合)보도드의 물리적(物理的) 및 기계적(機械的) 성질(性質)을 측정(測定)분석(分析)한 바 다음과 같은 결과(結果)를 얻었다. 1. 큰 파아티클과 작은 파아티클로 제조(製造)한 보오드에서 철선구성층수(鐵線構成層數) 및 구성철선(構成鐵線)의 수(數)가 많은 보오드일수록 그 비중(比重)은 컸었다. 2. 큰 파아티클로 제조(製造)한 보오드는 철선구성(鐵線構成)으로 인하여 두께팽창율(膨脹率)의 감소(減少)가 뚜렷하였으며 특히 철선구성층수(鐵線構成層數)가 많을수록 이 팽창율(膨脹率)은 더 개선되었다. 3. 큰 파아티클 및 작은 파아티클로 제조(製造)한 보오드 공(共)히 철선구성층수(鐵線構成層數)가 증가(增加)함에 따라 철선(鐵線)의 강도적(强度的) 특성(特性)이 파아티클 휨강도(强度) 성질(性質)을 보강(補强)하여 파괴계수(破壞係數), 탄성계수(彈性係數), 휨 극한하중(極限荷重) 일량(量) 등(等)이 개선(改善)되었으며, 2층(層) 및 3층(層) 철선구성(鐵線構成)보오드의 경우 보오드의 하층(下層)의 철선구성방향(鐵線構成方向)이 보오드의 길이방향(方向)과 일치(一致)하는 보오드가 특(特)히 큰 휨강도(强度) 향상(向上)을 보여 인장라미네이션을 얻었다. 4. 1층(層) 철선구성(鐵線構成)보오드는 철선구성간격(鐵線構成間隔)에 따른 개구면적(開口面積)과 파아티클의 크기에 따라 파괴계수(破壞係數), 탄성계수(彈性係數), 휨 극한하중(極限荷重) 일량(量) 등(等)이 다르게 나타났으나, 큰 파아티클로 제조(製造)한 보오드의 파괴계수(破壞係數)는 개구면적(開口面積)이 1.5~3$cm^2$이고, 나비 방향(方向)의 철선구성간격(鐵線構成間隔)이 1~2cm이면서 길이방향(方向)의 철선구성간격(鐵線構成間隔)이 1.5~2.5cm인 보오드가 높은 값을 나타냈고 작은 파아티클로 제조(製造)한 보오드의 파괴계수(破壞係數)는 개구면적(開口面積)이 0.5~1.5$cm^2$ 및 3.75~6.25$cm^2$이고 나비 방향(方向)의 철선간격(鐵線間隔)이 0.5cm이거나 2.5cm인 보오드가 높은 값을 나타냈다. 5. 큰 파아티클로 제조(製造)한 1층(層) 철선구성(鐵線構成)보오드의 탄성계수(彈性係數)는 개구면적(開口面積)이 1.5~3$cm^2$이고 나비방향(方向) 및 길이방향(方向)의 철선구성간격(鐵線構成間隔)이 1~2.5cm에서 큰 값을 나타냈으며, 한편 작은 파아티클로 제조(製造)한 보오드의 탄성계수(彈性係數)는 개구면적(開口面積)이 0.75~1.25$cm^2$ 민 3~6.25$cm^2$이고, 나비방향(方向)의 철선구성간격(鐵線構成間隔)이 0.5 또는 2.5cm에서 큰 값을 나타내었다. 6. 큰 파아티클로 제조(製造)한 1층(層) 철선구성(鐵線構成)보오드의 휨 극한하중(極限荷重) 일량(量)은 개구면적(開口面積)이 1~3$cm^2$인 보오드가 큰 값을 보였고, 작은 파아티클로 제조(製造)한 보오드의 경우의 그것은 철선(鐵線)의 개구면적(開口面積)이 좁은 것이 크게 나타났다. 7. 박리저항(剝離抵抗) 및 나사못보지력(保持力)은 큰 파아티클로 제조(製造)한 3층(層) 및 2층(層) 철선구성(鐵線構成)보오드에서 대부분(大部分) 대조(對照)보오드보다 큰 값을 보였으나 작은 파아티클로 제조(製造)한 보오드에서는 뚜렷한 경향이 없었다. 큰 파아티클로 제조(製造)한 1층(層) 철선구성(鐵線構成)보오드의 박리저항(剝離抵抗) 및 나사못보지력(保持力)은 전체적으로 비슷한 수준(水準)을 보였고 작은 파아티클로 제조한 보오드에서는 개구면적(開口面積)이 증가(增加)함에 따라 박리저항(剝離抵抗)은 증가(增加)하고 나사못보지력(保持力)은 감소(減少)하는 현상(現象)을 보였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.278-278
• /
• 2009

A photovoltaic device consisting of arrays of radial p-n junction wires enables a decoupling of the requirements for light absorption and carrier extraction into orthogonal spatial directions. Each individual p-n junction wire in the cell is long in the direction of incident light, allowing for effective light absorption, but thin in orthogonal direction, allowing for effective carrier collection. To fabricate radial p-n junction solar cells, p or n-type vertical Si wire cores need to be produced. The majority of Si wires are produced by the vapor-liquid-solid (VLS) method. But contamination of the Si wires by metallic impurities such as Au, which is used for metal catalyst in the VLS technique, results in reduction of conversion efficiency of solar cells. To overcome impurity issue, top-down methods like noble metal catalytic etching is an excellent candidate. We used noble metal catalytic etching methods to make Si wire arrays. The used noble metal is two; Au and Pt. The method is noble metal deposition on photolithographycally defined Si surface by sputtering and then etching in various BOE and $H_2O_2$ solutions. The Si substrates were p-type ($10{\sim}20ohm{\cdot}cm$). The areas that noble metal was not deposited due to photo resist covering were not etched in noble metal catalytic etching. The Si wires of several tens of ${\mu}m$ in height were formed in uncovered areas by photo resist. The side surface of Si wires was very rough. When the distance of Si wires is longer than diameter of that Si nanowires are formed between Si wires. Theses Si nanowires can be removed by immersing the specimen in KOH solution. The optimum noble metal thickness exists for Si wires fabrication. The thicker or the thinner noble metal than the optimum thickness could not show well defined Si wire arrays. The solution composition observed in the highest etching rate was BOE(16.3ml)/$H_2O_2$(0.44M) in Au assisted chemical etching method. The morphology difference was compared between Au and Pt metal assisted chemical etching. The efficiencies of radial p-n junction solar Cells made of the Si wire arrays were also measured.

• Journal of Magnetics
• /
• 제21권4호
• /
• pp.516-523
• /
• 2016

In this paper, coupling factors are calculated based on numerical analysis in order to assess various non-uniform low-frequency magnetic field exposure situations. Two types of non-uniform magnetic field sources are considered; circular coil and parallel wires with balanced currents. For each magnetic field source, source current values are determined so that reference magnetic field magnitude can be measured at the specified point on the human model. Various exposure situations are investigated by changing parameters such as the distance between source and human model, radius of circular coil, and the gap between parallel wires. For equivalent human models, prolate spheroid model and simplified human model from IEC 62311 standard are used. The calculated coupling factor values are compared with those obtained by 2D uniform disk human model, and the dependence of coupling factor on the choice of equivalent human model is analyzed.

• 전기전자학회논문지
• /
• 제22권3호
• /
• pp.846-849
• /
• 2018

Wireless power transfer (WPT) is the technology that enables the power to transmit electromagnetic field to an electrical load without the use of wires. There are two kinds of magnetic resonant coupling and inductive coupling ways transmitting from the source to the output load. Compared with microwave method for energy transfer over a long distance, the magnetic resonance method has the advantages of reducing the barrier of electromagnetic wave and enhancing the efficiency of power transmission. In this paper, the wireless power transfer circuit having a resonant frequency of 13.45 MHz for the low power system is studied, and the hardware implementation is accomplished to measure the power transmission efficiency for the distance between the transmitter and the receiver.

• 대한치과교정학회지
• /
• 제54권4호
• /
• pp.257-263
• /
• 2024

Objective: Lingual fixed retainers, made from 0.0175-inch 3-strand twisted stainless steel wire (TW) and 0.016 × 0.022-inch straight rectangular wire (RW), are generally used in clinical practice. This study aimed to calculate their accuracy by comparing the discrepancy between computer-aided customized retainers made from these two types of wires. Methods: Eleven orthodontic patients were selected, resulting in 22 maxillary and mandibular three-dimensional printing dental models. Two types of lingual fixed retainers were bonded from canine to canine. To determine the accuracy, five points were chosen for each model, resulting in 110 selected points. The absolute values of the distances on the x-, y-, and z-axes were measured to compare the accuracy of the two types of computer-aided retainers. Results: The accuracy of the two types of retainers did not differ significantly in the x- and z-axes, but only in the y-axis (P < 0.01), where RW-fixed retainers exhibited a slightly but significantly increased distance compared to the TW. Conclusions: Both types of retainers showed high accuracy; however, RW had a slight but statistically significant difference along the y-axis compared with TW. This type of computer-aided design/computer-aided manufacturing bending machine is limited to two dimensions, and the dental arch is curved. Therefore, RW may require slight manual adjustment by the practitioner after manufacturing.