• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.36-41
• /
• 2010

High Mn steel has been developed for automotive applications since the steel has an excellent combination of strength and ductility. However, from the viewpoint of welding, high Mn steel has a few problems related to its chemical composition. This paper describes characteristics of dissimilar $CO_2$ laser welding for expanding application of high Mn steel. From this work it was cleared that dissimilar laser welded joint between high Mn steel and carbon steel had poor formability due to the formation of martensite within weld metal. In order to improve ductility of welded joint, the method of controlling the dilution ratio of high Mn steel was suggested.

• 비파괴검사학회지
• /
• 제31권5호
• /
• pp.536-542
• /
• 2011

원자력발전소의 이종금속 용접부는 PWSCC 결함에 민감한 것으로 알려져 있으며 기량검증된 검사자가 기량검증된 절차서를 사용하여 가동중검사 기간 중에 주기적인 검사를 수행하고 있다. 국내 원자력발전소 이종금속 용접부의 형상 조사 결과에 따르면 대부분의 이종금속 용접부가 경사진 노즐부나 인접부에 위치하는 것으로 나타났다. 일반적인 초음파 탐촉자를 사용하여 경사부위에 위치한 이종금속 용접부의 검사를 수행할 경우 초음파 탐촉자의 접근성이 제한되어 검사체적을 모두 검사하기가 어렵다. 특히 축방향 결함 검출을 위한 원주방향 주사에서는 초음파 탐촉자가 경사면에 위치하게 되면 반사체로부터 결함 신호를 얻기 가 어려우며 이에 따라 결함 검출이 어렵게 된다. 이러한 문제점을 극복하기 위해서는 경사면을 고려하여 비틀림 각도를 적용한 초음파 탐촉자를 사용하는 것이 필요하다. 모델링을 통하여 비틀림 굴절 종파탐촉자 를 설계하고 축방향 결함 검사용 비틀림 굴절 종파탐촉자를 제작하여 실험을 통하여 결함으로부터 신호를 취득하였다. 일반 탐촉자와 비틀림 각도가 적용된 탐촉자의 초음파 응답신호를 비교한 결과 비틀림 각도가 적용된 탐촉자의 초음파 응답신호가 훨씬 뛰어난 것으로 나타났다.

• 한국압력기기공학회 논문집
• /
• 제6권2호
• /
• pp.34-41
• /
• 2010

This work is concerned with the analysis of stress corrosion cracking(SCC) behavior of Alloy 600 nozzle penetration mock-up according to a residual stress induced by a dissimilar metal welding(DMW) in a nuclear reactor pressure vessel. The effects of the dimension and materials of the nozzle penetration on the deformation and the residual stress induced by DMW were investigated using a finite element analysis(FEA). The inner diameter(ID) change of the nozzle by DMW and its dependance on the design variables, calculated by FEA, were well consistent with those measured from the mock-up. Accelerated SCC tests were performed for three mock-ups with different wall thicknesses in a highly acidic solution to investigate mainly the effect of the residual stress on the SCC behavior of Alloy 600 nozzle. From a destructive examination of the mock-up after the tests, the SCC behavior of the nozzle was fairly related with the residual stress induced by DMW : axial cracks were found in the ID surface of the nozzle within the J-weld region where the highest tensile hoop stress was predicted by FEA, while circumferential cracks were observed beyond both J-weld root and toe where the highest tensile axial stress was expected.

• 한국기계가공학회지
• /
• 제19권3호
• /
• pp.29-35
• /
• 2020

This paper studies the main parameters of tube-to-bar dissimilar material and shape friction welding for piping materials. The weldability of joint parts was investigated with respect to tensile tests, micro-Vickers hardness, the bond of area, and optical microstructure. The specimens are tested as-welded. Optimal welding conditions are n = 2000 rpm, HP = 50 MPa, UP = 100 MPa, HT = 5 sec, and UT = 10 sec when the metal loss (Mo) is 11 mm. Moreover, the same two materials for friction welding are strongly mixed with a well-combined structure of micro-particles without any molten material, particle growth, or defects. Therefore, the expected result of dissimilar material friction welding includes a reduction of cost and material in the welding process.

• 비파괴검사학회지
• /
• 제29권3호
• /
• pp.256-263
• /
• 2009

After several PWSCCs were found in Bugey(France), Ringhals(Sweden), Tihange(Belgium), Oconee, Arkansas, Crystal Fever, Davis-Basse, VC Summer(U.S.A.), Thuruga(Japan), USNRC and PNNL started the research on PWSCC, that is, the PINC project. USNRC required KINS to participate in the PINC project in May 2005. KINS organized the Korean consortium at March 2006 and Pre-RRT for RVHP were performed for the preparation of PINC RRT. Through these preliminary RRT, Korea NDE teams can learn and develop the detection and sizing technique for RVHP dissimilar metal weld. These techniques are now being prepared in Korea and need to be utilized for the In-service inspection of the RVHP and BMI of Korea Nuclear Power Plants. PINC RRT mock-ups will be helpful to training.

• Journal of Welding and Joining
• /
• 제23권6호
• /
• pp.43-48
• /
• 2005

This work was carried out to obtain sound welds and to select a most suitable binary metal joint among three different dissimilar binary metal combinations such as Zr-4/Ta, Mo/Ta and Ti/Ta(seal tube/sensor sheath) joints fur the instrumented nuclear fuel irradiation test. To do this, Taguchi experimental method was employed to optimize the experimental data. In addition, metallography, micro-focus x-ray radiography and hardness test were conducted to examine the welds. From the weld bead appearance, penetration depth and bead width as well as weld defects standpoint, Zr-4/Ta joint is suggested for the circumferential joining between a seal tube and a sensor sheath. The optimized welding parameters based on Zr-4/Ta joint are suggested as well.

• Nuclear Engineering and Technology
• /
• 제53권6호
• /
• pp.1846-1857
• /
• 2021

Ultrasonic nondestructive testing is important for monitoring the structural integrity of dissimilar metal welds (DMWs) in pressure vessels and piping in nuclear power plants. However, there is a low probability of crack detection via inspection of DMWs using ultrasonic waves because the grain structures (grain orientations) of the weld area cause distortion and splitting of ultrasonic beams propagating in anisotropic media. To overcome this issue, the grain orientation should be known, and a precise ultrasonic wave simulation technique in anisotropic media is required to model the distortion and splitting of the waves accurately. In this study, a method for nondestructive prediction of the DMW grain orientations is presented for accurate simulation of ultrasonic wave propagation behavior in the weld area. The ultrasonic wave propagation behavior in anisotropic media is simulated via finite-element analysis when ultrasonic waves propagate in a transversely isotropic material. In addition, a methodology to predict the DMW grain orientation is proposed that employs a simulation technique for ultrasonic wave propagation behavior calculation and an optimization technique. The simulated ultrasonic wave behaviors with the grain orientations predicted via the proposed method demonstrate its usefulness. Moreover, the method can be used to determine the focal law in DMWs.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.48-53
• /
• 2008

Although Magnetic Pulse Welding(MPW) is not a recently developed technique, it has gained the attention of the automotive industry. MPW has become an accepted welding process because it enables the joining of similar, and dissimilar materials, with a very short cycle time, without the need for filler metal and gases. In this study, the effect of the stand-off distance on the weld strength has been investigated. The compressive strength of the MPW joints was evaluated using UTM. The interface of weld, IMC composition and morpology were studied by SEM and EDS. It was concluded that the stand-off distance and the voltage are the main parameters influencing the strength of weld. In case of too high stand-off distance, it influenced harmful effect because of the resistance of deformation.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.42-62
• /
• 1997

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. Recently, automobile industries are trying to replace partly steel sheets with aluminum alloy sheets. Among currently produced aluminum alloys, Al alloy sheets of Al-Mg-Si(6000 series) are being tested. Especially, 6000 series are the most probable substitute in view of strength and weldability. In this paper, an attempt was made to apply resistance spot welding to joining of dissimilar sheet metals (KS6383+SCPZn or KS6383+SHCP). An effort was made to balance heating rate in the Al alloy with that in the steel sheets by increasing electrode tip diameter. Although resistance spot welding of Al alloy sheet and sheet metals does not produce desirable nugget, it proved to have reasonable strength if optimal weld condition is found by tensile-shear strength and fatigue life test. Since spot weld joints in automobile are always experiencing repeated load, spot welding methodology proposed in this paper is found to be not suitable to automobile body manufacturing.

• 대한기계학회논문집A
• /
• 제34권3호
• /
• pp.333-340
• /
• 2010

본 논문은 Alloy 82/182를 용가재로 사용한 SA508 Gr.3 노즐과 F316L 스테인리스강 안전단 사이의 이종금속 용접부에서 상온의 인장물성치와 파괴물성치를 평가하였다. 이를 위해서 두 모재와 열영향부, 버터링부, 그리고 용접부 내의 각 위치에서 채취된 시편을 이용하여 인장시험과 J-R 시험을 수행하였다. 시험 결과 Alloy 82/182 용접 루터부가 상부에 비해 높 은 강도를 보였다. 용접 루터부에서는 항복강도와 인장강도가 위치에 따라 크게 변화하였다. 버터링 부분이 가장 낮은 강도를 보였으며, F316L 스테이리스강 인접부로 갈수록 강도가 증가하였다. 반면, 용접 상부에서는 위치에 따른 강도의 변화가 크지 않았다. Alloy 82/182 용접부는 모재와 열영향부에 비해 낮은 파괴인성을 보였다. Alloy 82/182 용접부 내에서는 용접부 중심이 용접 경계부와 버터링부에 비해 약간 낮은 파괴인성을 보였으며, 용접 루터부가 용접 상부에 비해 높은 파괴인성을 보였다.