• 대한기계학회논문집A
• /
• 제36권2호
• /
• pp.137-148
• /
• 2012

가압경수로의 많은 관통관 중에서 니켈 기저 합금인 Inconel alloy 600 계열의 이종금속용접부는 일차수응력부식균열에 민감하며, 이를 평가하기 위하여 용접부에 작용하는 잔류응력분포를 정확히 예측하는 것이 중요하다. 본 논문에서는 유한요소해석을 이용하여 노즐 맞대기 이종금속용접부에 작용하는 일반적인 잔류응력분포를 예측하였다. 이를 위해 노즐 맞대기 이종금속용접부의 형상을 단순화하여 특정한 형상 변수에 따른 용접부 잔류응력분포를 확인하였으며, 이를 토대로 기존 문헌에 제시된 오스테나이트계 배관 맞대기 용접부 잔류응력 분포식을 수정하여 가압경수로 노즐 맞대기 이종금속용접부에 작용하는 일반적인 잔류응력분포 예측식을 제시하였다.

• 대한기계학회논문집A
• /
• 제39권10호
• /
• pp.979-984
• /
• 2015

본 논문에서는 국내 가동 중인 원자력발전소의 안전주입노즐을 대상으로 안전단의 길이와 동종금속용접부의 두께가 이종금속용접부의 응력분포에 미치는 영향을 평가하였다. 이를 위해 4가지의 서로 다른 안전단 길이와 4가지의 서로 다른 동종금속용접부 두께를 고려한 상세 2차원 유한요소 열해석 및 응력해석을 수행하였다. 유한요소해석 결과 동종금속용접부의 두께는 안전단의 길이가 짧은 경우 축방향 응력에 어느 정도 영향을 미쳤으나 원주방향 응력에는 거의 영향을 미치지 않았다. 안전단의 길이는 길이가 증가함에 따라 내면에서의 축방향 및 원주방향 응력값이 증가하는 것으로 나타났으나 특정 안전단 길이를 기준으로 응력분포가 구분되는 경향을 나타냈다.

• 한국레이저가공학회지
• /
• 제3권2호
• /
• pp.13-24
• /
• 2000

The weldability of dissimilar materials between sintered materials which are consisted of Co, Co＋Ni and carbon steel has been investigated using CO$_2$ laser. Autogeneous CO$_2$ laser welding were run along the butt between two alloys using sets of parameters variation-power and travel speed. In order to study weldability, mechanical tests (bending strength test, microhardness test) and metallurgical analyses (microstructure, phase transformation, fracture mode) were carried out. From the results obtained, it was found that the porosity which exists in a weld metal greatly affects the soundness of the weld. The optimum energy input to have a proper strength over than the requirement by a specification, found to be around 0.3-0.35kJ/m. There are two kinds of fracture mode in the weld metal, depending upon alloy combination, brittle fracture in the case of Co-carbon steel and a ductile fracture in the case of Co＋Ni-carbon steel. In general, Co＋Ni sintered material showed a better weld properties as compared to the Co sintered material.

• Journal of Welding and Joining
• /
• 제19권4호
• /
• pp.379-383
• /
• 2001

Resistance spot welding has been widely used in the sheet metal joining processes because of low cost, high productivity and convenience. Recently, automobile and aerospace industries are trying to replace partly steel sheets with aluminum alloy sheets. But in the case of dissimilar materials, to apply resistance spot welding has been known to be very difficult owing to the effect of melting temperature. On this study, an effort was made to apply spot welding of dissimilar sheet metals, 2024 aluminum alloy and zinc coated steel sheet, evaluate the spot weld quality with tensile-shear strength test and nondestructive evaluation technique, C-scan image methodology. In this study results, as the current below 11 kA, melting of materials is not achieved well. Also as the current exceeds to 13.5 kA, the more spatters happen at welded zone and tensile-shear strength lowered. So, the feasibility of C-scan image technique proposed in the study is found to be suitable evaluation method for resistance spot weldability.

• 비파괴검사학회지
• /
• 제35권1호
• /
• pp.52-60
• /
• 2015

원자력발전소에는 탄소강과 스테인리스강 용접을 위해 alloy600 용접재를 적용한 이종금속용접부가 다수 존재하며, 전 세계적으로 이종금속용접부에서 결함 발생 보고가 지속되고 있다. 주기적인 건전성 평가를 위해 이종금속용접부 초음파검사 일반절차서 (KPD-UT-10)를 적용하여 검사를 수행하고 있으며, 검사절차서에서는 탐촉자와 검사체 표면 사이의 간격을 최대 1/32"(0.8mm) 이내로 제한하고 있다. 국내의 일부 이종금속용접부는 테이퍼진 형상과 불규칙한 표면 형상을 가지고 있어, 가변형 위상배열초음파기술을 적용하여 검사 신뢰성을 높이고자 본 연구를 수행하였다. 연구 결과, 검사체 표면이 불규칙한 시편 내부의 인공결함에 대한 검출이 양호하였고, 이를 통해, 가변형 위상배열초음파기술의 현장 적용 가능성을 확인하였다.

• 대한기계학회논문집A
• /
• 제30권4호
• /
• pp.402-408
• /
• 2006

Dissimilar friction welding were produced using 15(mm) diameter solid bar in chrome molybedenum steel(KS SCM440) to carbon steel(KS S45C) to investigate their mechanical properties. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond of area and H.A.Z and microstructure investigations. The specimens were tested as-welded and post-weld heat treated(PWHT). The tensile strength of the friction welded steel bars was increased up to 100% of the S45C base metal under the condition of all heating time. Optimal welding conditions were n=2,000(rpm), $P_1=60(MPa),\;P_2=100(MPa),\;t_1=4(s),\;t_2=5(s)$ when the total upset length is 5.4 and 5.7(mm), respectively. The peak of hardness distribution of the friction welded joints can be eliminated by PWHT. Two different kinds of materials are strongly mixed to show a well-combined structure of macro-particles without any molten material and particle growth or any defects.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.152-154
• /
• 2005

Austenitic stainless steel has good weldability but is sensitive to hot cracking such as solidification crack and liquation crack. In this study, the specimens of dissimilar metals made between austenitic stainless steel and Al-brass were welded by GTAW process using four different filler metals. Cracks were detected in the heat-affected zone of the stainless steel when welded with CuAl, CuSn and NiCu filler metals, but no cracks were detected a Ni filler metal was used. The cracks propagated along the grain boundary in the heat affected zone near the fusion line to base metal of 316L stainless steel. The cracks were located inside the weld bead with very fine hairline crack. All cracks initiated at the fusion line and moved forward in the base metal. From energy dispersion spectroscopy (EDS), Cu peak was detected only in the crack-opening area.

• Journal of Welding and Joining
• /
• 제15권2호
• /
• pp.43-53
• /
• 1997

The complete joining method for dissimilar press punch materials and its real-time evaluation method is not available at present. Brazing method has been used for joining them, but it is known that the welded joint by the brazing has the lower bonding efficiency and reliability than the diffusion welding. The friction welding with a diffusion mechanism in bonding was applied in this study. This work was carried out to determine the proper friction welding conditions and to analyze mechanical properties of friction welded joints of sintered carbide tool materials (SKNM50 for the blade part of press punch) to alloy steel (SCM440 for the shank part of press punch) using aluminum (A6061 for the interlayer material) as an insert material between the sintered carbide tool materials and the alloy steel. In addition, acoustic emission test was carried out during friction welding to evaluate the weld quality.

• Journal of Welding and Joining
• /
• 제12권4호
• /
• pp.127-140
• /
• 1994

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. In the resistance spot welding processes the size of molten nugget is a criterion to assess weld quality. Many research have founded on measuring weld nugget size at the same time monitoring welding process parameters such as dynamic resistance and electrode movement. With increasing demand of energy saving, many efforts were made to employ aluminum alloys that are lighter than steel and have relatively equivalent strength to steel in the automobile industry. In this paper, spot weldability of aluminum alloys for various welding conditions were examined by series of experiments. One of the 6000 series (Mg-Si) aluminum alloy, 6383-T4 was chosen, which is currently considered as a substitute for the galvanized steel. Dynamic resistance, electrode movement and corresponding nugget size were observed and compared to the case of steel. Finally, resistance spot welding of dissimilar material (galvanized steel-aluminum alloy) was attempted.

• Journal of Welding and Joining
• /
• 제4권3호
• /
• pp.32-42
• /
• 1986

In this study, the influence of carbon equivalents on friction welds of dissimilar steels was investigated. Four types of carbon steels with 10mm diameter were welded to a high-speed tool steel SKH 9. Main experimental results could be summarized as follows (1) Under constant friction pressure, the friction time increased almost linearly with the increasing burn-off length, while the forge length decreased almost linearly. (2) The maximum hardness in carbon steels increased almost linearly with the increasing carbon equivalent, but was much lower than that in the high speed steel. (3) After quenching and tempering of dissimilar steel friction welds, the hardness in carbon steel weldments became similar as that in the base metal, while the hardness in SKH 9 weld was still higher that of the base metal. (4) Relative movement in the friction phae occurred not at the interface of the weldments, but in the high speed steed steel near the interface. (5) For considered material combinations and welding parameters, most of fractures in tension and twisting tests occurred in the base metal. And welds with so high strength could produced in a wide range of welding parameters.