• 동력기계공학회지
• /
• 제7권4호
• /
• pp.61-66
• /
• 2003

In this paper, the relation between displacement of piezoelectric material and electric field was proposed. FEA was introduced to predict the displacement and reaction force of plate spring attached in the piezoelectric material. The relation between displacement of piezoelectric material forced by plate spring and applied electric field were further verified by experimental investigation. Also, the flow rate of gas in piezoelectric valve was examined by experiment. Finally, the relation between electric field and gas flow was derived. Based on these results, these relations can be used in the design of mass flow controller.

• Structural Engineering and Mechanics
• /
• 제51권1호
• /
• pp.163-180
• /
• 2014

In the displacement based finite element analysis of composite beams that consist of two Euler-Bernoulli beams juxtaposed with a deformable shear connection, the coupling of the displacement fields may cause oscillations in the interlayer slip field and reduction in optimal convergence rate, known as slip-locking. In this study, the B-bar procedure is proposed to alleviate the locking effects. It is also shown that by changing the primary dependent variables in the mathematical model, to be able to interpolate the interlayer slip field directly, oscillations in the slip field can be completely eliminated. Examples are presented to illustrate the performance and the numerical characteristics of the proposed methods.

• Geomechanics and Engineering
• /
• 제10권1호
• /
• pp.1-19
• /
• 2016

This paper presents the results of an intensive experimental investigation on cyclic behavior of various sands and structural materials interface. Comprehensive measurements of the horizontal displacement and shear stresses developed during testing were performed using an automated constant normal load (CNL) cyclic direct shear test apparatus. Two different particle sizes (0.5 mm-0.25 mm and, 2.0 mm-1.0 mm) of sands having distinct shapes (rounded and angular) were tested in a cyclic direct shear testing apparatus at two vertical stress levels (${\sigma}=50kPa$, and 100 kPa) and two rates of displacement ($R_D=2.0mm/min$, and 0.025 mm/min) against various structural materials (i.e., steel, concrete, and wood). The cyclic direct shear tests performed during this investigation indicate that (i) the shear stresses developed during shearing highly depend on both the shape and size of sand grains; (ii) characteristics of the structural materials are closely related to interface response; and (iii) the rate of displacement is slightly effective on the results.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.463-468
• /
• 2002

This study investigates the variations of shear force, displacement, and fracture surface with the shear speed and the number of reflows. The experimental data of shear tests indicate that the shear force increases as increasing the number of reflows and the shear speed due to the formation of a kind of intermetallic compound, Ni$_3$Sn$_4$, on Au/Ni/Cu pad, and the work-hardening. However, general trends show that the shear force decreases due to increasing the thickness of the intermetallic compound over 4x reflow. It is observed that the intermetallic compound which is formed between solder and pad increases according to increasing the number of reflows, and the growth rate of the intermetallic compound at central region on the interface is faster than one at edge part. The general tendencies of shear force and displacement with different shear speeds are almost identical as an increase of the number of reflows.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.336-340
• /
• 1997

For optimal design of micro stage, we were measured to displacement of piezo-electric transducer that was based on voltage value. And then researchers were analyzed to microstage through FEM with displacement data including voltage value of piezo-electric transducer. For verification of analyzing results, we were gauged on displacement by using Laser-interferometer. And researchers were confirmed to propriety of micro stage design with FEM, were obtained error rate that are 3.5% between measurement results and analyzing results.

• 한국소음진동공학회논문집
• /
• 제16권7호
• /
• pp.739-745
• /
• 2006

This paper presents a novel type of hybrid dispensing head for IC fabrication and surface mount technology. The proposed mechanism consists of solenoid valve and piezoelectric stack as actuators, and provides positive-displacement and jet dispensing. The positive-displacement dispensing can produce desired adhesive amount without viscosity effect, while the jet dispensing can produce high precision adhesive amount. In order to determine the relationship between required voltage of the piezoelectric actuator and needle displacement, both static and dynamic analysis are undertaken, In addition, finite element analysis is performed in order to find optimal design parameters. Dispensing flow rate and pressure in the chamber are evaluated through fluid dynamic model.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.821-826
• /
• 2006

This paper presents a novel type of hybrid dispensing head for IC fabrication and surface mount technology. The proposed mechanism consists of solenoid valve and piezoelectric stack as actuators, and provides positive-displacement and jet dispensing. The positive-displacement dispensing can produce desired adhesive amount without viscosity effect, while the jet dispensing can produce high precision adhesive amount. In order to determine the relationship between required voltage of the piezo actuator and needle displacement, both static and dynamic analysis are undertaken, In addition, finite element analysis is performed in order to find optimal design parameters. Dispensing flow rate and pressure in the chamber are evaluated through fluid dynamic model.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제5권4호
• /
• pp.580-597
• /
• 2013

Three materials SUS304, 9% Ni steel and Al 5083-O alloy, which are considered possible candidate for International Maritime Organization (IMO) type B Cargo Containment System, were studied. Monotonic tensile, fatigue, fatigue crack growth rate and Crack Tip Opening Displacement tests were carried out at room, intermediate low ($-100^{\circ}C$) and cryogenic ($-163^{\circ}C$) temperatures. The initial yield and tensile strengths of all materials tended to increase with decreasing temperature, whereas the change in elastic modulus was not as remarkable. The largest and smallest improvement ratio of the initial yield strengths due to a temperature reduction were observed in the SUS304 and Al 5083-O alloy, respectively. The fatigue strengths of the three materials increased with decreasing temperature. The largest increase in fatigue strength was observed in the Al 5083-O alloy, whereas the 9% Ni steel sample showed the smallest increase. In the fatigue crack growth rate test, SUS304 and Al 5083-O alloy showed a decrease in the crack propagation rate, due to decrease in temperature, but no visible improvement in da/dN was observed in the case of 9% Ni steel. In the Crack Tip Opening Displacement (CTOD) test, CTOD values were converted to critical crack length for the comparison with different thickness specimens. The critical crack length tended to decrease in the case of SUS304 and increase for the Al 5083-O alloy with decreasing temperature. In case of 9% Ni steel, change of critical crack length was not observed due to temperature decrease. In addition, the changing material properties according to the temperature of the LNG tank were analyzed according to the international code for the construction and equipment of ships carrying liquefied gases in bulk (IGC code) and the rules of classifications.

• 한국임상수의학회지
• /
• 제36권1호
• /
• pp.68-73
• /
• 2019

We determined the risk factors for displacement of the abomasum (DA), and the relationships between DA and postpartum disorders, milk yield, and reproductive performance in dairy cows. Initially, we identified the risk factors for DA using data regarding cow health and calving season from 2,208 lactations. Then, we compared the incidence of postpartum disorders, culling, death, and reproductive performance between cows with DA and their control herdmates (each n = 57). In addition, serum metabolites concentrations and milk yield were compared between cows with DA and controls (each n = 33). Ketosis (odds ratio [OR] = 9.27, p < 0.0001) and twin calves (p = 0.06) increased the risk of DA. Cows with a parity of three had a higher risk (OR = 5.23, p < 0.01) of DA than primiparous cows. Serum total cholesterol concentration was lower but non-esterified fatty acid, ${\beta}-hydroxybutyrate$, and alanine aminotransferase concentrations were higher after calving in cows with DA than in controls (p < 0.05). The removal rate from the herd by 2 months after calving was higher (p < 0.05) but milk yield 1 and 2 months after calving (p < 0.01) and the rate of first insemination by 150 days postpartum were lower (hazard ratio = 0.49, p < 0.05) in cows with DA than controls. In conclusion, higher parity, twin calves, and ketosis are risk factors for DA in dairy cows, which is associated with a higher removal rate from the herd, lower milk yield, a longer calving to first insemination interval, and unfavorable levels of metabolites related to energy and liver function.

• Steel and Composite Structures
• /
• 제18권1호
• /
• pp.29-50
• /
• 2015

With a quasi-three point bending apparatus, ratcheting deformation is studied experimentally on a pressurized austenitic stainless steel Z2CND18.12N pipe under bending load and vertical displacement control, respectively. The characteristic of ratcheting behavior of straight pipe under both control methods is achieved and compared. The cyclic bending loading and internal pressure influence ratcheting behavior of pressurized straight pipe significantly under loading control and the ratcheting characteristics are also highly associated with the cyclic displacement and internal pressure under displacement control. They all affect not only the saturation of the ratcheting strain but the ratcheting strain rate. In addition, ratcheting simulation is performed by elastic-plastic finite element analysis with ANSYS in which the bilinear model, Chaboche model, Ohno-Wang model and modified Ohno-Wang model are applied. By comparison with the experimental data, it is found that the CJK model gives reasonable simulation. Ratcheting boundaries under two control modes are almost same.