• 한국전기전자재료학회논문지
• /
• 제28권12호
• /
• pp.792-796
• /
• 2015

With high integration of electronic components, power inductors are also miniaturized. Recently, thick film processes for small size power inductors were developed and commercialized. However, the thick film process to prepare soft magnetic green sheets was not reported enough. In this study, we used Fe-Si magnetic and CIP (carbonyl iron powders) as starting materials to lead to a bimodal particle size distribution in the sheet. We proposed a newly developed 'Modified slurry preparation process' to get well dispersed condition even at high solid contents. Using the new process, it was possible to prepare a well dispersed slurry over 70 vol% of solid. BYK-103 was better than BYK-111 as dispersant in this slurry and the optimum amount was 0.6 wt%. The optimized slurry was formed into a sheet by tape casting process and then the sheet was laminated. We conformed that small size powder, large size powder, and epoxy resin were well dispersed in the green sheet.

• 한국지구과학회지
• /
• 제35권5호
• /
• pp.313-323
• /
• 2014

We secured the high dispersion spectra of the symbiotic star CI Cyg. The HI, HeI, and HeII line profiles were analyzed using the relatively long exposure data including 1800 sec (Sep. 12, 1998, phase=0.90), 3600 sec (Aug. 12, 2002, ${\phi}=0.47$), and 1800 sec (Oct. 21, 2009, ${\phi}=0.54$). Although a minor outburst was reported in 2008, our three observation periods were generally known to be quiescent in earlier photometric studies. With the help of hydrodynamic simulations, we identified the two emission zones responsible for the blue- and red-shifted line components: (a) an accretion disk around a hot white dwarf star which consists of the outer cool HeI emission zone and the inner hot HeII emission part, and (b) a high density zone near the inner Lagrangian point responsible for the HeI line flux variation and the broadening of its line profile. The HeII line fluxes indicate that the HeII emission zone of the accretion disk is relatively stable, implying a constant gas inflow from the giant star throughout the quiescent period. The 2002 HeI data showed that the notable mass flow activity through the inner Lagrangian point occurred during this period and its flux intensity became strongest, whereas the HeII line width in the same period indicates that its flow activity forced the accretion disk to expand. The [OIII] lines were observed in 1998 but not detected in 2002 and 2009, implying the disappearance of the low density zone. Based on our kinematical studies upon the line profiles, we conclude that CI Cyg was stable in 1998 among the three observation periods selected in this research.

• 천문학회보
• /
• 제41권1호
• /
• pp.33.1-33.1
• /
• 2016

Dwarf elliptical galaxies (dEs), the most abundant galaxy type in clusters, were recently shown to exhibit a wide variety in their properties. Particularly, the presence of blue cores in some dEs, what we call dE(bc), supports the scenario of late-type galaxy infall and subsequent transformation into red, quiescent dEs. While several transformation mechanisms for these dE(bc)s within cluster environment have been proposed, all these processes are able to explain only some of the observational properties of dEs. In this context, internal kinematic properties of dE(bc)s provide the most crucial evidence to discriminate different processes for the formation of these galaxies. We present Gemini Multi Object Spectrograph (GMOS) long-slit spectroscopy of two dE(bc)s in the Virgo cluster. We obtained radial profiles of velocity and velocity dispersion out to ~1.3 effective radius. We found that two dE(bc)s exhibit kinematically decoupled components as well as distinct peculiar features in velocity profiles, supporting the scenario of mergers. We also found that these galaxies are structurally compatible with low surface brightness component of blue compact dwarf galaxies. We suggest that a part of dE(bc)s in the Virgo Cluster were formed through galaxy merger in low density environment such as galaxy group or outskirt of the cluster, and then were quenched by subsequent effects within cluster environment.

• 접착 및 계면
• /
• 제3권4호
• /
• pp.44-52
• /
• 2002

Composite materials are created by combining two or more component to achieve desired properties which could not be obtained with the separate components. The use of reinforcing fillers, which can reduce material costs and improve certain properties, is increasing in thermoplastic polymer composites. Currently, various inorganic fillers such as talc, mica, clay, glass fiber and calcium carbonate are being incorporated into thermoplastic composites. Nevertheless, lignocellulose fibers have drawn attention due to their abundant availability, low cost and renewable nature. In recent, interest has grown in composites made from lignocellulose fiber in thermoplastic polymer matrices, particularly for low cost/high volume applications. In addition to high specific properties, lignocellulose fibers offer a number of benefits for lignocellulose fiber/thermoplastic polymer composites. These include low hardness, which minimize abrasion of the equipment during processing, relatively low density, biodegradability, and low cost on a unit-volume basis. In spite of the advantage mentioned above, the use of lignocellulose fibers in thermoplastic polymer composites has been plagued by difficulties in obtaining good dispersion and strong interfacial adhesion because lignocellulose fiber is hydrophilic and thermoplastic polymer is hydrophobic. The application of lignocellulose fibers as reinforcements in composite materials requires, just as for glass-fiber reinforced composites, a strong adhesion between the fiber and the matrix regardless of whether a traditional polymer matrix, a biodegradable polymer matrix or cement is used. Further this article gives a survey about physical and chemical treatment methods which improve the fiber matrix adhesion, their results and effects on the physical properties of composites. Coupling agents in lignocellulose fiber and polymer composites play a very important role in improving the compatibility and adhesion between polar lignocellulose fiber and non-polar polymeric matrices. In this article, we also review various kinds of coupling agent and interfacial mechanism or phenomena between lignocellulose fiber and thermoplastic polymer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.145-148
• /
• 2003

Recently, the recycle of CMP (chemical mechanical polishing) slurries have been positively considered in order to reduce the high COO (cost of ownership) and COC (cost of consumables) in CMP process. Among the composition of slurries (buffer solution, bulk solution, abrasive particle, oxidizer, inhibitor, suspension, antifoaming agent, dispersion agent), the abrasive particles are one of the most important components. Especially, the abrasive particles of slurry are needed in order to achieve a good removal rate. However, the cost of abrasives, is still very high. In this paper, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size and hardness. Also, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slury, As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• 한국작물학회지
• /
• 제28권2호
• /
• pp.211-215
• /
• 1983

수집된 재래의 유색대두종을 일률적인 재배조건하에서 종실특성 변이와 종실종군별 생육진전 및 수량형질 특성을 조사한 결과 다음의 결론을 얻었다. 1. 유색대두 수집종들은 100립중을 기준으로 하여 20gr 이하의 소립중, 20-25gr의 중립중, 25-30gr의 대립종 및 30gr 이상의 특대립종 등 4개군으로 나눌 수 있었다. 2. 종실크기에 관련된 요인중 종실장과 종실폭의 변이는 종실후보다 크게 나타났다. 3. 종실중과 경중 및 주당협수 등의 형질들은 변이계수에서 생육일수나 결과일수 등의 형질보다 큰 경향이었다. 4. 생육일수와 성숙일수 및 개화시기는 립중군별간에 유의한 차이를 나타내지 않았다. 5. 개화기와 성숙일수는 경장 및 경중과 정의 상관관계를, 경장과 경중은 수량형질과 정의 상관을 나타내었으며, 주당협수는 100립중과 부의 상관을, 또한 수량과는 정의 상관관계를 나타내었다.

• 한국약용작물학회지
• /
• 제26권4호
• /
• pp.317-327
• /
• 2018

Background: The root of Angelica gigas Nakai is used as a traditional herbal medicine in Korea for the treatment of many diseases. However, the poor water solubility of the active components in A. gigas Nakai is a major obstacle to its bioavailability. Methods and Results: This work aimed at enhancing the solubility of the active compounds of A. gigas Nakai by a chemical (using a surfactant) and physical (hot melt extrusion, HME) crosslinking method. Fourier transform infrared spectroscopy revealed multiple peaks in the case of the extrudate solids, attributable to new functional groups including carboxylic acid, alkynes, and benzene derivatives. Differential scanning calorimetry analysis showed that the extrudate soilid had a lower glass transition temperature ($T_g$) and enthalpy (${\Delta}H$) ($T_g:43^{\circ}C$, ${\Delta}H$ : < 6 J/g) as compared to the non-extrudate ($T_g:68.5^{\circ}C$, ${\Delta}H:123.2$) formulations. X-ray powder diffraction analysis revealed the amorphization of crystalline materials in the extrudate solid. In addition, enhanced solubility (53%), nanonization (403 nm), and a higher amount of extracted phenolic compounds were achieved in the extrudate solid than in the non-extrudate (solubility : 36%, nanonization : 1,499 nm) formulation. Among the different extrudates, acetic acid and span 80 mediated formulations showed superior extractions efficiency. Conclusions: HME successfully enhanced the production of amorphous nano dispersions of phenolic compound including decursin from extrudate solid formulations.

• 비파괴검사학회지
• /
• 제24권4호
• /
• pp.341-347
• /
• 2004

발전설비의 중요한 요소인 배관의 효율적인 비파괴검사를 위해, 배관내에 유도초음파를 comb 트랜스듀서를 이용하여 발생시켰으며, 유도초음파를 비접촉 방식으로 수신하기 위해 An(air-coupled transducer)를 적용하였다. comb 트랜스듀서의 요소간격과 이론적인 분산선도로부터 발생가능 한 유도초음파 모드가 예측되었다. 또한 예측된 모드를 수신하기 위해 각 모드의 이론적인 위상속도를 이용하여 ACT의 수신 각도를 결정하였다. 수신모드의 특성을 규명하기 위해 웨이블릿 변환과 2D-FFT를 이용한 시간-주파수해석을 수행하여 이론적인 분산선도와 비교한 결과, 수신된 보드는 이론적으로 예측된 모드와 일치하는 것으로 나타났다.

• Geomechanics and Engineering
• /
• 제18권1호
• /
• pp.85-96
• /
• 2019

A free vibration analysis and wave propagation of triclinic and orthotropic plate has been presented in this work using an efficient quasi 3D shear deformation theory. The novelty of this paper is to introducing this theory to minimize the number of unknowns which is three; instead four in other researches, to studying bulk waves in anisotropic plates, other than it can model plates with great thickness ratio, also. Another advantage of this theory is to permits us to show the effect of both bending and shear components and this is carried out by dividing the transverse displacement into the bending and shear parts. Hamilton's equations are a very potent formulation of the equations of analytic mechanics; it is used for the development of wave propagation equations in the anisotropic plates. The analytical dispersion relationship of this type of plate is obtained by solving an eigenvalue problem. The accuracy of the present model is verified by confronting our results with those available in open literature for anisotropic plates. Moreover Numerical examples are given to show the effects of wave number and thickness on free vibration and wave propagation in anisotropic plates.

• Bulletin of the Korean Chemical Society
• /
• 제19권3호
• /
• pp.299-307
• /
• 1998

PM3 semiempirical calculations were carried out to study the frequency-dependent nonlinear optical properties of thiophene, furan, pyrrole, (1,2,4)-triazole, (1,3,4)-oxadiazole, and (1,3,4)-thiadiazole monomers and oligomers. The longitudinal component, αxx, is the largest of three principle components. On the other hand, the out-of-plane component, αzz, is the smallest. Moreover, the out-of-plane component (αzz) of thiophene, furan, pyrrole, (1,2,4)-triazole, (1,3,4)-oxadiazole, and (1,3,4)-thiadiazole monomers show constant changes with increasing optical frequencies. The frequency-dependent first- order polarizabilities increase in the order: thiophene > (1,2,4)-triazole > pyrrole > furan > (1,3,4)-thiadiazole > (1,3,4)-oxa-diazole monomers and oligomers. The effects of β(-2ω;ω,ω) (SHG) shows a larger dispersion compared with (-ω;ω,0) (EOPE) and β(0;-ω,ω) (OR). The second- order polarizabilities of thiophene, furan, pyrrole, (1,2,4)-triazole, (1,3,4)-thiadiazole, and (1,3,4)-oxadiazole monomers for the various second- order effects have the order: β(-2ω;ω,ω) (SHG) > β(-ω;ω,0) (EOPE) > β(0;-ω,ω) (OR) and thiophene > pyrrole > (1,2,4)-triazole > furan > 1,3,4-thiadiazole > 1,3,4-oxadiazole monomers. The third- order polarizabilities for the various third- order effects have the following order: γ(-3ω;ω',ω,ω) (THG) > γ(-2ω;0,ω,ω) (EFISHG) > γ(-ω;ω',-ω,ω) (IDRI) > γ(-ω;0,0,ω) (OKE). The effects of THG increase rapidly with increasing optical frequencies compared with the other effects. In particular, OKE effects increase most slowly with increasing optical frequencies. Also, the effects of THG for thiophene, furan, pyrrole, (1,2,4)-triazole, (1,3,4)-thiadiazole, and (1,3,4)-oxadiazole oligomers show the order thiophene > (1,2,4)-triazole > furan > pyrrole > (1,3,4)-thiadiazole > (1,3,4)-oxadiazole oligomers. In particular, the third- order polarizabilities of thiophene and (1,3,4)-thiadiazole oligomers are about four and three times larger than those of (1,3,4)-oxadiazole and (1,2,4)-triazole oligomer, respectively.