• International Journal of Aeronautical and Space Sciences
• /
• 제6권2호
• /
• pp.84-96
• /
• 2005

Helical tip vortex is known as stable vortex structure, however the specific frequency component of far wake perturbation induces the vortex pairing in hover and axial flight. It is expected that the tip vortex pairing phenomena may happen in transition flight and very low advance ratio flight so that inflow may be most nonuniform in the low advance ratio flight. The objectives of this paper are that a tip-vortex instability during the transition from hover into very low advance ratio forward flight is numerically predicted to understand a physics by using a time-marching free-wake method. To achieve the objectives, numerical method is firstly validated in typical axial and forward flights cases. Present scheme with trim routine can predict airloads and inflow distribution of forward flight with good accuracy. Then, the transition flight condition is calculated. The rotor used in this wake calculation is a small-scale AH-1G model. By using a tip-vortex trajectory tracking method, the tip-vortex pairing process are clearly observed in transient flight($\mu$=0.03) and disappears at a slightly higher advance ratio($\mu$=0.05). According to the steady flight simulation at $\mu$=0.03, it is confirmed the tip-vortex pairing process is continued in the rear part of rotor disk and not occurs in the front part. Time averaged inflow in this case is predicted as smooth distribution.

• 한국입자에어로졸학회지
• /
• 제15권4호
• /
• pp.139-148
• /
• 2019

This study was performed for the application of a high-speed centrifugal cyclone to shale gas mining process. This device uses the centrifugal force to control particles similar to typical cyclones, and the disk located inside the cyclone is forced to rotate using a motor. The pressure difference occurred during the rotating of disk. Hence, inflow rate was generated without a blower fan. In addition, flow rate increased with elevating rpm of motor. The installing the disk in multiple stages on the inner rotor increased the instantaneous disk outlet flow. Hence, the control efficiency of oil particle increased from 1.05% to 31.2%. By modifying the structure of the disk so that the air flow to the opposite direction of the cyclone, the control efficiency of oil particles increased to 81.5%. By increasing the capacity of the motor and the size of the disk, the flow rate was increased to 2.5 ㎥/min because the rpm of motor and pressure difference increased. As rpm of motor increased, the cut-off diameter (d_pc) became smaller. Unlike the Lapple's equation, d_pc was inversely proportional to the effective number of rotations (N_e). The control efficiency was maintained even if the concentration of oil particles increased, for this reason, the higher the oil concentration, the more particles were accumulated and controlled.

• 전력전자학회논문지
• /
• 제10권2호
• /
• pp.148-154
• /
• 2005

SRM은 회전자의 위치에 따라 상권선의 여자시점이 결정되므로 회전자의 정확한 위치정보가 요구된다. 회전자 위치검출을 위해 절대형 엔코더 및 레졸버를 사용할 경우 초기 회전자 위치 검출이 가능하여 초기기동이 가능하지만 경제성을 고려할 때 적절하지 않다. 증분형 엔코더의 경우 초기 회전자 위치 검출이 용이하지 않아 초기기동의 문제가 있고, 홀센서를 이용할 경우 별도의 링마그넷을 부착하여야 하는 단점이 있다. 초기기동과 경제성을 고려할 때 슬롯디스크 및 옵토 인터럽터를 이용한 광센서 기법이 적합하지만, 이 방식은 6/4 pole SRM의 경우 3개의 옵토 인터럽터와 슬롯디스크가 필요하다. 반면에 본 논문에서는 단지 2개의 광센서만을 이용하여 3상 6/4 pole SRM을 구동하였으며 초기기동 및 정·역 운전을 가능하게 하였다. 광센서의 개수를 1개 줄이고 슬롯디스크를 제거함으로써 제작의 편리성과 경제성이 개선되었으며 슬롯디스크 취부면적이 제거되어 모터의 부피도 줄일 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.233-237
• /
• 2014

In this paper, the finite element modeling of the RK4 rotor kit system (RK4) and then frequency analysis and transient analysis, and was compared with the actual experimental results. RK4 manufactured by General Electric for the purpose of education and research. It is composed of two shaft, Two shaft is connected using a flexible coupling, one disk is mounted. The analytical model is modeled by using the ANSYS finite element analysis program commercially available. Based on impact hammer test results, material properties and the stiffness of the bearing and coupling was tuned. Considering the operating conditions and the vibration response of the analytical model were compared with experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.641-645
• /
• 2001

Storage drives for mobile devices, such as laptop computers or PDAs, are changing now. The data density of storage drives is becoming higher and sizes of those are becoming smaller and thinner. Spindle motors for rotating disk are also becoming smaller and thinner. But, large torque is required to reduce seek time. In this research, inner rotor type spindle motor suitable for thin thickness has been developed. Rotor and stator are optimized structurally for large torque performance with small size. Especially, high vibration and shock performances, which are essential to mobile devices, are analyzed in detail.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.659-662
• /
• 2003

This paper analyzes the electro-mechanical characteristics of the spindle motor in a computer hard disk drive due to the trapezoidal and sinusoidal driving methods. The driving circuit equation is modified by considering the switching action of PWM inverter, and is coupled with the Maxwell equation for the analysis of the magnetic field. Mechanical motion of a rotor is calculated by solving Newton-Euler equation. Electro-mechanical excitation and dynamic response are characterized by analyzing the free response of a rotating rotor and Fourier analysis of the excitation force.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권9호
• /
• pp.889-894
• /
• 1997

A miniaturized wind-mill type ultrasonic motor which has diameter in 12.7 mm and thickness in 2.0mm using PMN-PZT piezoelectric ceramics was fabricated. The wind-mill type ultrasonic motors has only three plate and of two wind-mill shape slotted metal endcaps a rotor whose end is hollowed out so that its periphery fits with the shape of the stator and a bearing to guide the rotor. A Finite Element Analysis was carried out to obtain the endcaps behavior under a radial displacement change of piezoelectric disk and to optimize the structure of the number of slots. Increasing the applied voltage the revolution speed of ultrasonic motors was increased. The maximum speed of 700 rpm and the maximum torque of 0.22 nN·m of the wind-mill type ultrasonic motors were obtained.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권3호
• /
• pp.105-109
• /
• 2001

In this paper, the windmill type ultrasonic motors with 11.35 mm diameter, 2.87 mm thickness of metal endcap and 1.47 g weight were fabricated. Effects of slots and thickness on torque characteristic in the windmill type ultrasonic motor were investigated, when stator's slots were changed from 4, 6, 8 and thickness 0.15 mm, respectively. Specially designed metal endcaps with windmill shaped cutting can provide longitudinal and torsional displacements simultaneously as the ceramic disk vibrates radically. The windmill type ultrasonic motor has only three components: a stator element with windmill shape slotted metal endcap, a rotor and bearing. Ultrasonic motor stimulated to ultrasonic oscillations by piezoelectrics to drive a rotor via friction contact. The ultrasonic motor fabricated here was the windmill type ultrasonic motor operated by single-phase AC source. Bidirectional revolution using single-phase high frequency for driving the ultrasonic motor was presented.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.255-264
• /
• 1999

Friction characteristics of automotive friction materials containing different metallic fibers rubbing against Al-MMC and cast iron disk specimens have been studied. Friction materials containing aluminum, copper or low steel carbon fiber were tested. Friction tests were composed of three different phases to investigate the effect of temperature, pressure, speed, and drag time. The results showed that the friction material containing Al fibers has lower friction force and wear amount than the others with Cu or Steel fiber. On the other hand, the wear of friction material was severe in the case of using Al-MMC rotors. These results showed that the thermal decomposition of solid lubricants (and organic components), formation of transfer layer, and SiC particles in the AI-MMC rotor play crucial roles in determining the friction characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.183-186
• /
• 2007

This Paper presents a solution to control the Brushless DC Motor(BLDCM) in Hard Disk Drive(HDD) using the Linear Quadratic Regulator(LQR). Generally, The speed of BLDCM in HDD is controlled by the lead angle control or the input voltage control using PAM(Pulse Amplitude Modulation) etc. These control methods have speed overshoot in speed control and need the long time until BLDCM reaches at the steady state. In order to improve the performance, this paper present the PI speed controller using the LQR based on vector control and the rotor position detection methods at the space vector PWM inverter. The proposed methods are proved by the simulation and experimental results.