• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.2
• /
• pp.200-213
• /
• 2000

Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.

• Journal of Korea Multimedia Society
• /
• v.8 no.10
• /
• pp.1322-1328
• /
• 2005

The circulation flows passing through the Ekman boundary layer on the rotating disk and transfer the angular momentum into the interior region of the container. Consequently, the circulation enhances the momentum transfer and the interior fluid is divided by a propagating shear front. This investigation focuses on computer vision and image processing technique for analysis of Non-Newtonian Fluids. To visualize marching velocity shear front for the transient flow, a particular shaped particles and light are used. To validate the proposed method, quantitative image are compared with the optical data acquired by a direct measurement of LDV (Laser Doppler Velocimetry).

• Transactions of Materials Processing
• /
• v.15 no.1 s.82
• /
• pp.3-8
• /
• 2006

The demand fer small and high-capacity optical data storage devices has rapidly increased. The areal density of optical disk is increased by using higher numerical aperture objective lens and shorter wavelength source. A wafer-scale stacked micro objective lens with a numerical aperture of 0.85 and a focal length of 0.467mm for the 405nm blue- violet laser was designed and fabricated. A diffractive optical element (DOE) was used to compensate the spherical aberration of the objective lens. Among the various fabrication methods for micro DOE, the UV-replication process is more suitable fur mass-production. In this study, an 8-stepped DOE pattern as a master was fabricated by photolithography and reactive ion etching process. A flexible mold was fabricated for improving the releasing properties and shape accuracy in UV-replication process. In the replication process, the effects of exposing time and applied pressure on the replication quality were analyzed. Finally, the surface profiles of master, mold and molded pattern were measured by optical scanning profiler. The geometrical deviation between the master and the molded DOE was less than $0.1{\mu}m$. The diffraction efficiency of the molded DOE was measured by DOE efficiency measurement system which consists of laser source, sample holder, aperture and optical power meter, and the measured value was $84.5\%$.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.2
• /
• pp.115-120
• /
• 2005

As a popularity of a portable digital device such as a cellular phone, a digital camera and a MP3 player is spreading, the demand of the mobile storage device increases rapidly. A bluray technology using 405nm laser diode and objective lens having high NA(Numerical Aperture), 0.85, satisfies a miniaturization and a high capacity which are the requirements of the portable device. To develop SFFOP(small form factor optical pickup), it is prerequisite to minimize the number of optical components and establish evaluation and assembly method of micro optical pickup system as well as mass production method of micro optical component. To minimize optical elements of optical pickup, there have been many researches to use P-HOE(Polarized Holographic Optical Element) due to its extremely small size and versatile function. However, P-HOE is handled and assembled very accurately in SFFOP. In this paper, static error signal detection method is developed for an alignment of P-HOE in SFFOP. Using developed static error signal detection method, P-HOE can be aligned very accurately with real time result of static error signals of pickup such as FES(focusing error signal) and TES(Tracking Error Signal). The developed static error signal detection method is verified by the evaluation of commercialized DVD Pickup. And finally. developed static error signal detection method is applied for the assembly of P-HOE in SFFOP system satisfies specification of BD(Blu-ray Disk).

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.09a
• /
• pp.35-40
• /
• 2005

The demand for small and high-capacity optical data storage devices has rapidly increased. The areal density of optical disk is increased using higher numerical aperture objective lens and shorter wavelength source. A wafer-scale stacked micro objective lens with a numerical aperture of 0.85 and a focal length of 0.467mm for the 405nm blue- violet laser was designed and fabricated. A diffractive optical element (DOE) was used to compensate the spherical aberration of the objective lens. Among the various fabrication methods for micro DOE, the UV-replication process is more suitable for mass-production. In this study, an 8-stepped DOE pattern as a master was fabricated by photolithography and reactive ion etching process. A flexible mold was fabricated for improving the releasing properties and shape accuracy in UV-molding process. In the replication process, the effects of exposing time and applied pressure on the replication quality were analyzed. Finally, the shapes of master, mold and molded pattern were measured by optical scanning profiler. The deviation between the master and the molded DOE was less than 0.1um. The efficiency of the molded DOE was measured by DOE efficiency measurement system which consists of laser source, sample holder, aperture and optical power meter, and the measured value was $84.5\%$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.3
• /
• pp.589-597
• /
• 1992

The effect of pressure on soot formation in premixed propane-air combustion is investigated at high pressures over the pressure range of 1 to 5 MPa by using a specially designed constant volume combustion bomb. The combustiom chamber of disk type with eight spark plugs located on the circumference at an interval of 45deg is 100mm in diameter by 14mm thick. The end gases are compressed to high pressures by the eight converging flames. The soot volume fraction in the chamber center during the final stage of combustion at the highest pressure is measured by the in-situ laser extinction technique, and the burnt gas temperature during the same period is measured by the two-color method. It is found that the soot yield rises with 50 to 100% for the respective equivalence ratio range of 1.9-2.2 at an interval of 0.1 when the combustion pressure is increased from 1 to 5 MPa, and that the turbulent flames decrease in the soot yield as compared with the laminar flames because the burnt gas temperatures increase with the drop of heat loss.

• Korean Journal of Materials Research
• /
• v.4 no.2
• /
• pp.233-240
• /
• 1994

We have investigated how the magneto-optical and recording properties of Pt/Co modulated films vary with sample preparation conditions : sputtering at various gas pressures, sputtering with Xe instead of Ar, and etching the buffer layers, etc. The magneto-optical characteristics of Pt/Co multilayers was comparable with those of currently prevailing rare-earth transition-metal alloys(Tb-Fe-Co amorphous films). On a disk of $12{\times}[Pt10.7\;{\AA}/Co2.8{\;}{\AA}]$ multilayer enhanced with 70nm silicon nitride, we have achieved a CNR of 36dB with a reading laser(${\lambda}\;=\;780nm$) power of 2.5-4.5mW for 720KHz carrier at 1.4m/s and the enhanced kerr rotation angle of $1.23^{\circ}$ at 780nm. It is suggested that Pt/Co modulated films clearly are very promising magneto-optical materials for a commercially use.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.43-54
• /
• 1999

The effects of equivalence ratio and pressure on burnt gas temperature in premixed fuel rich propane-oxygen-inert gas combustion are investigated over the wide ranges of equivalence ration from 1.5 to 2.7 and pressure from 0.1 to 7 MPa by using a specially designed disk -type constant-voume combustion chamber, The premixtures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree interals. The eight converging flames compress the end gases to high pressures. The burnt gas temperature is meausured by the nmodifie dtow-colr pyrometry method. The transmissivity in the chamber center during the final stage of combustion at the hightest pressure is meausred by in situ laser extinction method. It is found that a temperature difference between the burnt gas temperature measured by mofidied and conventrational two-color method is 10 to 20 K, but the accuracy of the modified two-color methdo is higher if the local transmissivity in observed region is uniform , and the combustion at higher pressures results gas density conditions and the burnt gas temperature increases as the volume fraction of argon is increased because the specific heat of argon is lower compared to that of nitrogen with a constant equivalence ratio.

• Journal of the Korean Institute of Educational Facilities
• /
• v.12 no.2
• /
• pp.5-13
• /
• 2005

The school library plays an important role to improve the student's mental activity and cultivate the formation of character and emotion. Especially in the information society, the students must collect, select and utilize the necessary information themselves. The school library has to collect, put in order and keep the book, audiovisual material and necessary information beyond it about the entire education and to offer the students and teachers them for the general school education. The school library has to be a center of school education and drive forwards the spontaneous and subjective learning activity as well as progress the education process. The school library must be the place to preserve the student's subjective study ability, that is, consolidate the materials as the study center and be composed of proper study materials for the solving-problem and research. Also to be perfect in the role of the information center, the school library has to be consolidated in accordance with development of various information softwares and ways including the newspaper, magazine, video, CD, laser disk and computer. It is required for the information of school library to be corresponded actively to the multi-media society.

• Transactions of the Society of Information Storage Systems
• /
• v.6 no.1
• /
• pp.12-17
• /
• 2010

Thermally-assisted magnetic recording (TAMR) is a potentially promising approach to increase the storage density of hard disk drive (HDD). However, TAMR has some issues such as temperature effects, media problems, thermal deformation and light delivery. In this research, we focused on light delivery. One of the powerful methods to deliver the light from laser diode to recording medium is the use of an optical fiber and a specially designed prism. However, the TAMR with optical fiber may have some flyability problems induced by the mounted optical fiber and prism. Also, the TAMR suspension using an optical fiber has high vertical and pitch stiffness. Therefore, p-torque is greatly increased by the optical fiber. Also, flying height (FH) of the slider with TAMR suspension can be largely changed by p-torque. Therefore, in this paper, we focus on the pitch static attitude (PSA) tolerance and the FH by PSA of the TAMR suspension. The FH is investigated using various errors and the PSA tolerance for TAMR suspension is proposed.