• Journal of computational fluids engineering
• /
• v.21 no.1
• /
• pp.64-71
• /
• 2016

This research is to numerically investigate the convective cooling performance in the Disk brake. Research concentrates on the heat transfer coefficient and cooling performance which are selected with cooling local locations. Cooling performance of the Hole disk has been compared by Ventilated Disk. According to the results of heat transfer on the disk brake, activated velocity distributions more appear in the Hole disk. This is due to the fact that a number of hole units have exactly 120 on the surface of the hole disk. Therefore, velocity distributions of hole disk brake is better activated than Ventilated disk. According to the calculations of Nusselt number between surface and atmosphere in the interested cooling area, average value of cooling effect has been increased 13.5% by the hole disk at driving of speed 65 km/h situation and grown 18% by the hole disk at driving speed of 100 km/h. Due to the flow of air through the hole route, cooling performance of the hole disk was very excellent. In addition, cooling effect on edge of the bottom is better than the vicinity of center.

• Journal of Power System Engineering
• /
• v.10 no.3
• /
• pp.67-72
• /
• 2006

The effect of manufacturing parameters on wear and improve cooling of motorcycle break system was studied using a disk-on-pad type friction tester. Such parameters conditions have an effect on the wear and improve cooling factor such as applied load, sliding speed, frictional time and number of ventilated disk hole. However, it is difficult to know the mutual relation of these factor. In this study, the wear and cooling characteristics using design of experiment containing 4 elements were investigated for an optimal condition for the best motorcycle disk break system employing Taguchi robust experimental design. From this study, the result was shown that vents have an effect on convection area improving more cooling ability and reduced wear of the disk.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.563-569
• /
• 2008

During braking operation, the surfaces of disk have severe contact conditions and high frictional heat would be generated between disk and pad surfaces. The heat makes high temperature gradient on disk surfaces and results in thermal deformation. To enhance the frictional heat dissipation, heat pipes are embedded in the ventilated type disk along the radial direction. The temperatures of the inner vent type disk and the brake disk with heat pipes are compared at the same operating conditions. By comparison a brake disk with heat pipes has higher cooling performance than the inner vent type disk.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.4 no.3
• /
• pp.233-241
• /
• 1992

Temperature distributions in a 3.5 inch hard disk drive including disk surface and internal air have been simulated numerically. Solutions were obtained from fifteen cases regarding three power consumption rates and five ambient conditions. As a result, the velocity of cooling air should be maintained greater than ㏐/s when the power consumption reached 3W in the disk drive. A correlation equation was proposed to predict the temperature field of disk surface and caseing surface.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.199-205
• /
• 1999

Using a coupled thermal-mechanical analysis, the thermal distortion of the ventilated disk brakes has been investigated based on the air cooling effects during 15 braking operations. The FEM results show that the bendings and distortions of the disk toward the left side are decreased, but the sinusoidal distortion of the disk rubbing surface along the arc length of the vent hole is highly increased by increasing the convective air cooling effects, which is heavily related to the squeal, wear and micro-thermal crackings at the rubbing surfaces due to uneven dissipation rates of friction heatings.

• Journal of The Korean Astronomical Society
• /
• v.28 no.1
• /
• pp.97-107
• /
• 1995

The stability of the geometrically thin, two-temperature hot accretion disk is studied. The general criterion for thermal instability is derived from the linear local analyses, allowing for advective cooling and dynamics in the vertical direction. Specifically, classic unsaturated Comptonization disk is analysed in detail. We find five eigen-modes: (1) Heating mode grows in thermal time scale, $(5/3)({\alpha}{\omega})^{-1}$, where alpha is the viscosity parameter and w the Keplerian frequency. (2) Cooling mode decays in time scale, $(2/5)(T_e/T_i)({\alpha}{\omega})^{-1}$, where $T_e\;and\;T_i$ are the electron and ion temperatures, respectively. (3) Lightman-Eardley viscous mode decays in time scale, $(4/3)(\Lambda/H)^2({\alpha}{\omega})^{-1}$, where $\Lambda$ is the wavelength of the perturbation and H the unperturbed disk height. (4) Two vertically oscillating modes oscillate in Keplerian time scale, $(3/8)^{1/2}\omega^{-1}$ with growth rate $\propto\;(H/\Lambda)^2$. The inclusion of dynamics in the vertical direction does not affect the thermal instability, adding only the oscillatory modes which gradually grow for short wavelength modes. Also, the advective cooling is not strong enough to suppress the growth of heating modes, at least for geometrically thin disk. Non-linear development of the perturbation is followed for simple unsaturated Compton disk: depending on the initial proton temperature perturbation, the disk can evolve to decoupled state with hot protons and cool electrons, or to one-temperature state with very cool protons and electrons.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.332-338
• /
• 1999

A coupled thermal-mechanical analysis has been presented for the thermal distortions of the ventilated disk brakes during IS braking operations. The FEM results show that the bendings and distortions of the disk toward the left side are decreased, but the sinusoidal distortion of the disk rubbing surface along the arc length of the vent hole is highly increased by increasing the convective air cooling effects, which is heavily related to the squeal, wear and micro-thermal crackings at the rubbing surfaces due to uneven dissipation rates of friction heatings.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.1
• /
• pp.62-66
• /
• 2011

In this study, the thermal performance of disk can be compared with disk and disk with holes through numerical analysis. The capacity of thermal emission on general disk becomes more than on disk with holes at the distribution of temperature at first and the magnitude of equivalent stress on general disk becomes less than on disk with holes at the distribution of stress. The capacity of thermal emission or the magnitude of thermal deformation on disk with holes becomes less than that on general disk 30 minutes later. The disk with holes is worn less and more durable than general disk. The performance of cooling and braking force at disk and pad can be improved by installing the disk with holes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.1
• /
• pp.36-41
• /
• 2002

The cause and the elimination method for the chattering phenomena were investigated in a check valve attached to the exit of an auxiliary cooling water pump in a Korean nuclear powerplant. From the site experiment and the numerical calculation, the incident angle of the disk was so small that it was not able to produce the sufficient lifting force to overcome the gravitational component of the disk weight. Moreover, it turned out that the installation position was not symmetric for the secondary vortical flow generated inside the elbow so that the flow structure had strongly unstable flow characteristics. From this study, the tapping noise and the chattering phenomena were eliminated exactly by changing the incidence angle of the valve disk and the installation position of the calve body.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.274-276
• /
• 2010

Three noise sources are come from note PC system; HDD, System Cooling Fan and ODD. Except HDD, user can accept as an acceptable operating noise. System Fan needs to cooling down the CPU and Chipset and ODD only works when it need to work, therefore user thinks these two noise sources are necessary. For the HDD, some times it makes noise without user HDD access action such as re-organizing cache and defragmentation, user can hardly accept this noise. At the circumstance like as library and the room at the dawn, user can recognize the noise easily so that makes dissatisfaction. I'm studying algorithm and method to reduce HDD noise for user satisfaction.