• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권6호
• /
• pp.230-235
• /
• 2003

In this paper, a superposed discharge type ozonizer with an internal dielectric that can be made into a vacuum tube has been designed and fabricated. Ozone generation and discharge characteristics have been investigated in accordance with output voltage of power supply, flow-rate, discharge power and vacuum of inside internal dielectric. Pure oxygen was used as the supply gas of the ozonizer. Ozone concentration and ozone generation are gradually increased when discharge power is increased at the same flow-rate and they are both proportional to the vacuum level. As such, the maximum ozone concentration of 8840 ppm was obtained at vacuum 0.1 Torr and flow-rate 0.5 $\ell$/min.

• International Journal of Aeronautical and Space Sciences
• /
• 제3권1호
• /
• pp.1-8
• /
• 2002

A numerical analysis was performed on the fluid flow in injector orifice of a liquid rocket engine. The present computational code was verified against the published data for turbulent flow in a pipe with a sudden expansion-contraction. Considered were the parameters for the flow analysis in an injector orifice: Reynolds number, ratio of mass flow rate of the injector orifice and inlet flow rate, and slant angle of the injector orifice. The discharge coefficient increased slightly as the Reynolds number increased. The slant angle of the injector changed critically the discharge coefficient. The discharge coefficient increased by 7% when the slant angle changed from $-30^{\circ}$ to $30^{\circ}$ The ratio of mass flow rate had relatively little impact on the discharge coefficient.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.381-385
• /
• 2003

In this paper, a co-axial type ozonizer varied with discharge gap was designed and manufactured for investigating $\circled1$ discharge characteristics with variation of output voltage power supply, flow rate and gap $\circled2$ ozone generation characteristics with variation of flow rate, gap and discharge power. pure oxygen was used as process gas of the co-axial type ozonizer. In this paper, a double cylindrical type superposed silent discharge type ozonizer which internal electrode can be produced a vacuum has been designed and manufactured. Discharge and ozone generation characteristics have been investigated in accordance with output voltage of power supply, flow-rate, discharge power and vacuum of internal electrode.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.98-106
• /
• 2002

The airflow characteristics of an air-conditioning duct with multiple diffusers were investigated through one-dimensional analysis, CFD simulation and experimental measurement. One-dimensional program based on Bernoulli's equation and minor loss equations was developed in order to evaluate the air distribution rate at each diffuser. In CFD simulation, three-dimensional flow characteristics inside air-conditioning duct were computed for incompressible viscous flow, adopting the RNG k-$\xi$turbulence model. Also, in an effort to equalize the discharge flow rate at each outlet, the optimization procedure has been performed to obtain the optimum diffuser area. In this process, square of difference between maximum discharge rate and minimum discharge rate is used as an object function. Diffuser area and discharge velocity are established as constraints. After optimization process, determined design variables are applied again in CFD simulation and experiment to validate the optimized result by one-dimensional program. Comparison with the experimental data of airflow rate distribution showed that the developed program seems to be acceptable and can be useful design tool for an automotive air-conditioning duct in an initial design stage.

• 설비공학논문집
• /
• 제27권9호
• /
• pp.468-474
• /
• 2015

When oil is used for cooking in detached or apartment houses, large amounts of oil-mist, smoke, and particulate substances are generated and dispersed into the indoor-air environment. These pollutants diffuse into the surroundings and spread their odor while rising fast at a high temperature due to the heat energy from the gas range. Although the exhaust gas is discharged from the exhaust hood, which is installed on the top of a gas range to remove the diffuse pollutants, the exhaust conditions can vary greatly because they depend on the shape of the exhaust hood and the discharge rate. In this paper, the air that is required for the gas-exhaustion process is supplied by an air curtain that surrounds the kitchen hood, and the pollutant-capturing efficiency varies depending on the angle of the discharge grills; the pollutant-capturing efficiency was studied using a numerical-analysis method. The results indicate that the pollutant-capturing efficiency is not significantly changed by a change of the discharge-grill angle at a low air-discharge rate; however, at a high air-discharge rate, the efficiency value increases with an increase of the discharge-grill angle, whereby the best value occurs at 30 degrees and the efficiency decreases above this angle. Below 30 degrees, the effect of the discharge rate on the capturing efficiency is more than that of the discharge-grill angle.

• 한국안전학회지
• /
• 제21권1호
• /
• pp.53-58
• /
• 2006

This paper has been addressed on the discharge characteristics of the ignition coil by Weibull function. It analyzed discharge number and amount of discharge using Weibull distribution to know the inter-relationship between partial discharge and mileage. We detected the discharge which happens for 10 seconds. The applied voltage increased by 0.5[kV] at discharge inception voltage. We diagnosed failure rate using the shape parameters. As a result, we confirmed that the failure rate was increased, because the shape parameter showed the value of 5 according to increasing mileage degradation. Also, it is considered to increase the degradation of inner insulator of ignition coil. Because failure rate of virgin was increased from 0[%] to 25[%] after degradation, stability analysis of the ignition coil using Weibull analysis is possible.

• 대한화학회지
• /
• 제38권3호
• /
• pp.214-220
• /
• 1994

금속시료를 직접분석하기 위하여 원자흡수법에 의한 글로우방전시스템을 구성하였다. 방전이 일어나는 양극과 음극은 가공성 세라믹을 이용한 arrestor에 의해 분리하였으며, 방전에 영향을 미치는 전류 및 전압, arrestor의 형태, 가스 압력 그리고 가스 흐름 등을 개인용 컴퓨터와 ADC/DAC board 및 RS-232를 사용하여 자동적으로 제어될 수 있도록 하였다. 여러가지 방전에 미치는 실험변수들을 변화시키면서 시료손실속도, 원자흡광도 등의 변화를 측정하였으며, sputtering 된 후의 시료 표면을 주사형 전자현미경으로 관찰하였다.

• Korean Chemical Engineering Research
• /
• 제46권5호
• /
• pp.852-857
• /
• 2008

광촉매의 고정화는 광촉매의 이용범위를 넓히기 위해서 매우 중요한 기술이다. 광촉매를 고정화시키기 위해 티타늄 표면을 양극산화 시켜 $TiO_2$로 전환시킬 수 있다. 양극산화에 의해 제조된 $TiO_2$는 광촉매 활성을 가지고 있으며 표면은 스펀지와 비슷한 형태를 나타내었다. 다양한 초기농도, 습도, 방전전압 하에서 양극산화에 의해 티타니아를 제조 이를 이용하여 기상의 아세트알데히드와 VOC의 광촉매 분해반응을 연구하였다. 양극산화 티타니아의 반응성은 상대습도가 증가함에 따라 증가하였으나 너무 높은 습도는 반응성을 감소시켰다. 광촉매 반응과 전기 방전을 결합시키면 VOC 제거효율이 크게 증가 되었으나, 과도한 전압을 가하여 코로나 방전이 발생되면 반응속도가 오히려 감소되었다. 최적 상대습도는 40%였으며 최적 방전전압은 암방전 영역인 5 kV였다.

• 한국전기전자재료학회논문지
• /
• 제11권11호
• /
• pp.1043-1048
• /
• 1998

The decomposition performance of the Surface induced Plasma Chemical Processing(SPCP) for benzene, toluene, xylene and $NO_2$ were experimentally examined. Discharge exciting frequency range was 5kHz and 10kHz, and low frequency discharge requires high voltage to inject high electric power in gas and to decompose contaminants. The decomposition rate of dioxide nitrogen for 5kHz power in gas and to decompose contaminants. The decomposition rate of dioxide nitrogen for 5kHz power supply is only 85%, but it’s rate for 10kHz power supply is very high, more than 96% when peak voltage is 12kv. Aromatic hydrocarbon vapor of up to 1000ppm is almost throughly decomposed at the flow rate of 1000$\ell$/min or lower rate under the discharge with electric power of several hundred watts. High decomposition rate is shown in every case, that is, for SPCP reactor is necessary to obtain the decomposition rate of more than 80~98%. The decomposition rate of benzene, toluene and xylene were 90~98% and dioxide nitrogen was 45~96%.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권1호
• /
• pp.15-21
• /
• 2002

We investigated effects of electrical, physical, and chemical parameters on energy transfer, NO conversion, and light emission in the dielectric barrier discharge (DBD) process. As gap distance between electrodes increased, discharge onset voltage increased. However, as gap distance between electrodes increased, electric field which initiates discharge showed approximately the same value, 30kV/cm. The discharge onset voltage of the coarse surface electrode was lower than that of the smooth surface electrode. And, energy transfer was slightly enhanced in the coarse electrode condition. However, NO conversion rate decreased with the coarse surface electrode because more uniform discharge can be obtained on the smooth surface electrode. The NO conversion rate increased with decreasing the initial concentration, so the DBD process is more feasible in the lower concentration condition. The variation of gas residence time tested at the same energy density in the experiment did not affect on the NO conversion. The result shows that the NO conversion rate mainly depends on the energy density. The DBD process is able to adjust on plasma-photocatalyst process because it emits the short wavelength light in the range of ultraviolet. The intensity of light emission increased with the increase of the energy transfer to the reactor and the gas flow rate.