• The Journal of Engineering Geology
• /
• v.21 no.2
• /
• pp.125-131
• /
• 2011

The discharge characteristics of the Seodo Mulgol Spring-the only groundwater-producing area in Dokdo-were evaluated by measurements of discharge rate and electrical conductivity (EC) on five occasions. The Seodo Mulgol Spring is fed by rainfall in upstream areas of the Mulgol cave, and the rainwater of the area moves down along cooling joints developed in trachyandesite II and trachyte, finally discharging at the Mulgol cave. The discharge rate of the Seodo Mulgol Spring varied from 1.12 to 7.02 $m^3/d$ during the study period and EC varied from 2,650 to 3,390 ${\mu}S/cm$, showing a sharp increase during heavy rainfall. The observed variations in discharge rate and EC at the Seodo Mulgol Spring are attributed to the relatively short distance between the recharge area and the Mulgol cave, and to the rapid movement of groundwater through columnar joints developed in trachyandesite II and trachyte. Additional discharge measurements, combined with precise rainfall data, are required at Dokdo to elucidate the discharge characteristics of the Seodo Mulgol Spring.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.7
• /
• pp.70-75
• /
• 2014

The experiment was done on traveling at the speed of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. The experimental method were employed to measure the waveform of secondary ignition coil and exhaust emission. In this experiment, the correlation between the secondary waveform coming from ignition coil and exhaust emission were measured in decrepit vehicle. The secondary waveform characterized by the value of effective discharge energy. The following results are obtained by analyzing the data relativity between the effective discharge energy and exhaust emission. The variation rate of effective discharge energy was largest 60km/h, 20km/h, 100km/h velocity in the ordered named. As the vehicle velocity increases, the average variation rate of CO and $NO_X$ decreases and that of HC and $CO_2$ decrease. The value of effective discharge energy, CO, $NO_X$ and fuel consumption is measured badly in case of car with failures in MAP, spark plug and good in case of car with before and after maintenance regardless of vehicle velocities. The value of effective discharge energy is to be nearly parabolic shape as vehicle velocity increases. As the value of effective discharge energy increases, the value of $NO_X$, HC and $CO_2$ decrease, the value of CO increase. The most sensible factors of exhaust emission were CO, $NO_X$, and the small variation factors were HC, $CO_2$.

• Journal of Preventive Medicine and Public Health
• /
• v.44 no.2
• /
• pp.84-92
• /
• 2011

Objectives: This study aimed to investigate smoking relapse and the related factors within 1 year after discharge from the smoking cessation clinics (SCCs) of public health centers (PHCs). Methods: Data were collected with a structured questionnaire from 395 people who success fully stopped smoking at 4 SCCs in Busan between May and June 2009, and this data were analyzed by Kaplan-Meier survival curves and the Cox proportional hazard model. Results: The rate of smoking relapse within 1 year after discharge from SCCs was 39.2% and this decreased rapidly over 6 months after discharge. The factors related to smoking relapse within 1 year after discharge from SCCs were being female (HR, 2.11; 95% CI, 1.17 to 3.82), a trial of smoking cessation with any assistants (HR, 1.95; 95% CI, 1.19 to 3.19), more than 7 ppm of exhaled CO2 on the SCCs' registration (HR, 1.81; 95% CI, 1.24 to 2.64), use of pharmacotherapy after discharge from SCCs (HR, 2.00; 95% CI, 1.36 to 2.93), alcohol drinking more than once a week after discharge from SCCs (HR, 3.32; 95% CI, 2.15 to 6.78), and a perceived barrier (HR, 1.21; 95% CI, 1.14 to 1.30) after discharge from the SCCs. Conclusions: According to the results, at least 6 months follow-up after discharge from SCCs of public health centers is recommended to reduce the rate smoking relapse. It is also recommended to strengthen the education on how to overcome barriers such as drinking in the course of smoking cessation clinics.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.12
• /
• pp.665-672
• /
• 2000

This paper described the measurement technology to analyze the partial discharge characteristics for long term aging of insulations. This system was consisted of high voltage generation and measurement part, PD detection part, digital conversion and signal processing part. We used the VXI system for digital conversion and signal processing part. In the digital conversion part, we studied the error of partial discharge magnitude and memory capacity for reading digital signal with the sampling rate. In the signal processing part, we showed the program algorithm to count pulses and read peak values of partial discharge. The allowable minimum sampling rate of digizer was decided to 250kS/s through analyzing test. We confirmed that this system was very useful in the study of $\phi-q-n$ characteristics of long term PD experiments with specimens being consisted of internal void defects and CIGRE II electrodes.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.157-163
• /
• 2017

This system is a diagnosis system that checks whether it causes a partial discharge of a power cable or not. PD(Partial Discharge) is detected by FBDS(Frequency Band Detection Sensor). That is, it means a acoustic sensor capable of detecting each frequency band. The wave shape of PD sound is similar to noise and is systematically generated by partial discharge. Therefore, in this paper, we could discriminate between normal and abnormal case using relative level crossing rate(RLCR) and spectrogram of frequency energy rate.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.6
• /
• pp.323-327
• /
• 2015

In this paper, parameters related with partial discharge (PD) were analyzed in SF₆ gas under AC and DC voltages. Three electrode systems (protrusion on conductor, protrusion on enclosure, and free particle) were fabricated to simulate PD defects in a gas-insulated switchgear (GIS). All electrode systems were filled with SF₆ gas at 0.5 MPa. PD pulses were detected using an oscilloscope and a data acquisition (DAQ) based on IEC 60270. To analyze the PD characteristics under AC and DC voltages, parameters such as discharge inception voltage (DIV), discharge extinction voltage (DEV), pulse magnitude, repetition rate, and T-F map were compared. From the experimental results, PD was revealed to have different characteristics under AC and DC, and these results may be useful for diagnosis of power facilities operated under HVDC.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.1
• /
• pp.26-33
• /
• 1990

The behavior and mixing process of the forced plume are studied in the hydraulic laboratory. The dilution rate of discharged waste water from the port in various hydraulic condition was analized. The effect of densimetric Froude number and the discharge type on the dilution rate are discussed: In the vertical discharge, the forced plume of small densimetric Froude number mixes more actively than that of the large one. In the horizontal discharge, forced plume of large densimetric Froude number dilutes more rapidly than that of the small one. The mixing takes place more vigorously in the horizontal discharge than in the vertical one. The multi-port diffuser is more effective for the waste water discharge system than the single port diffuser in the tidal swinging coastal sea.

• Journal of Korea Water Resources Association
• /
• v.37 no.8
• /
• pp.675-685
• /
• 2004

In this study, overflow behaviors through a partially open tainter gate mounted on a standard ogee spillway were investigated by using the FLOW-3D. The results indicated that the discharge coefficient is in the range of 0.685 to 0.723. A relation of gate-controlled discharge to free discharge was proposed and a reasonable correlation between the free and controlled discharge was obtained. Pressures on the spillway crest and the gate were also investigated. As the gate opening rate decreases with a fixed gate opening height and the gate opening height increases at a fixed gate opening rate, negative pressures on the spillway crest and the dimensionless maximum pressures on the gate increase.

• Environmental Engineering Research
• /
• v.10 no.3
• /
• pp.144-154
• /
• 2005

The use of ozone gained acceptance in the production of ultrapure water because of its powerful oxidizing ability. Ozone is currently used to deactivate microorganisms and remove organic contaminants. However, interest also exists in using radical species, which arc stronger oxidants than ozone, in such processes. One means of producing radical species is by corona discharge. This work investigates the use of a novel pulseless corona-discharge system for the removal of organic substances in ultrapure water production. The method combines corona discharge with electrohydrodynamic spraying of oxygen, forming microbubbles. Experimental results show that pulseless corona discharge effectively removes organics, such as phenol and methylene blue, in deionized water. The corona-discharge method is demonstrated to be comparable to the direct use of ozone at a high-applied voltage. The results also show that a minimum applied voltage exists for operation of the corona-discharge method. In this work, the minimum applied voltage is approximately 4.5 kV. The kinetic rate or phenol degradation in the reactor is modeled. Modeling results show that the dominant species of the pulseless corona-discharge reactor are hydroxyl radical and aqueous electron. Several radical species produced in the pulseless corona-discharge process are identified experimentally. The. major species are hydroxyl radical, atomic hydrogen species, and ozone.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.1-8
• /
• 2007

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke marine diesel engine is of great economic importance. In Korea, authors first developed a motor-driven cylinder lubricator for a Wartsila Switzerland large two-stroke diesel engine. The characteristic of the developed product is that can control automatically the oil feed rate with a load fluctuation by the motor drive and the offset cam. For manufacturing the reliable and useful products, however, it is necessary to investigate further characteristics and to improve performances as a cylinder lubricator. In this study, the effects of pump motor speed, plunger stroke and cylinder back pressure on oil feed rate, maximum discharge and delivery pressures are experimentally investigated by using the electronically controlled quill injection system and distributer in the developed cylinder lubricator. It is found that the oil feed rates of electronic control and mechanical type quills with the in-cylinder back pressure are differently characterized by the role of accumulator, the viscous resistance of contact area, etc. It can be also shown that the maximum discharge pressure of the electronic control quill is lower than the mechanical type one but the maximum discharge pressure difference of two types decreased as plunger stroke is small, and the maximum delivery pressures of two types increased as plunger stroke, motor speed and back pressure are elevated but the maximum delivery pressure of mechanical type is higher than the one of electronic control type.