• Coupled systems mechanics
• /
• v.7 no.4
• /
• pp.441-453
• /
• 2018

Longitudinal fracture in a functionally graded beam configuration was studied analytically with taking into account the non-linear behavior of the material. A cantilever beam with two longitudinal cracks located symmetrically with respect to the centroid was analyzed. The material was functionally graded along the beam width as well as along the beam length. The fracture was studied in terms of the strain energy release rate. The influence of material gradient, crack location along the beam width, crack length and material non-linearity on the fracture behavior was investigated. It was shown that the analytical solution derived is very useful for parametric analyses of the non-linear longitudinal fracture behavior. It was found that by using appropriate material gradients in width and length directions of the beam, the strain energy release rate can be reduced significantly. Thus, the results obtained in the present paper may be applied for optimization of functionally graded beam structure with respect to the longitudinal fracture performance.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.26-30
• /
• 2001

Creep crack growth lift of high temperature pressure equipments was assessed for various crack locations and for various material properties. Surface cracks at the inner and outer surface of the vessel in the axial and circumferential directions were considered. The crack was located in the weld metal, in the parent metal or at the weld interface. Results shored that the crack at the weld interface was the most dangerous one. The crack located outside is weaker than that located inside. Safety factors of the case in which improper material properties were used the to unavailability of the correct material properties were discussed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.33-40
• /
• 2001

In this research, the cracking of tunnel concrete lining was investigated and analyzed through long-term measurement and nonlinear numerical analysis. For one year after the casting of lining, the stresses and strains were measured by the sensors installed in hard rock tunnel lining. The measurements showed that only small stresses which were less than cracking stress occurred in every survey sections regardless of sensor directions. It could be induced that the external load applied to the lining was small or ignorable. Also, it was carried out short-term numerical analysis based on such site condition as ambient temperature, the- degree of overbreak and mold staying period. Long-term numerical analysis based on creep & shrinkage and nonlinear cracking was carried out. The output showed that construction condition and ambient environments could make the lining concrete crack without external loads. The cracks formed in this process does not indicate the structural instability of the tunnel.

• Korean Journal of Materials Research
• /
• v.10 no.11
• /
• pp.784-788
• /
• 2000

The Vickers microhardness was measured on the basal (0001) plane of sapphire single crystals in the temperature range from 25$^{\circ}C$to 1000$^{\circ}C$. The substructure surrounding the indents was investigated using selective chemical polishing and etching, optical microscopy, and trasmission electron microscopy (TEM). At room temperature, cracks were predominant, and at intermediate temperatures (400$^{\circ}C$and 600$^{\circ}C$), extensive rhombohedral twinning was observed. On the other hand, at higher temperatures, prism plane slip bands on prism plane {1120}(원문참조) were dominant in the microstructure. TEM observations revealed that the dislocation substructure at the vicinity of the indents consisted of fairly straight dislocations lying in basal and/or prism planes and aligned along the <1100> and <1120> directions. The details of the glide dissociation of perfect <110> screw dislocations into three collinear 1/3<1100> partials on the prism plane and the Peierls potential for sapphire single crystals were discussed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.5 no.1
• /
• pp.9-23
• /
• 1985

Boshin-Kak Bell, which is one of the largest bells, is located at Chong-Ro Square in the center of Seoul. The bell has been struct early morning and late evening for time-report since the 14th century in Lee Era. Therefore Boshin-Kak Bell has been an intimate old friend of Seoul citizen more than 500 years. Unfortunately, motal large cracks were found inside this bell in the horizontal and vertical directions in 1979. The present paper has investigated the propagated bell-crack by ultrasonic flaw detecting method, and the stress level, bell vibration and weight measurement by electric wire resistance strain gauge method. The results indicate that they are useful for further study of Korean bell by nondestructive test.

• Journal of Power System Engineering
• /
• v.13 no.5
• /
• pp.52-58
• /
• 2009

A gas turbine consists of an upstream compressor and a downstream turbine with a combustion chamber, and also the compressor and the turbine are generally coupled using a single shaft. Many casing bolts are used to assemble two horizontally separated casings, the gas turbine casing and the compressor casing, in both of axial and vertical directions. Because drilled holes for casing bolts in vertical direction are often too close to drilled holes for casing bolts in axial direction, one can observe cracks in the area frequently during operations of a gas turbine. In this study of the root cause analysis for the cracking initiating from the drilled holes of the casings of a gas turbine, the finite element analysis(FEA) was applied to evaluate the thermal and mechanical characteristics of the casings. By applying the field operation data recorded from combined cycle power plants for FEA, thermal and thermo-mechanical characteristics of a gas turbine are analyzed. The crack is initiated at the geometrical weak point, but it is found that the maximum stress is relieved when the same type of cracks is introduced on purpose during FEA. So, it is verified that the local fracture could be delayed by machining the same type of defects near the hole for casing flange bolts of the gas turbine, where the crack is initiated.

• Journal of the Korean Vacuum Society
• /
• v.13 no.4
• /
• pp.175-181
• /
• 2004

We investigated the stability of the DLC film coated on 304 stainless steel substrate by Radio frequency assisted chemical vapor deposition method. Fracture and spallation behaviour of the coating was observed during micro-tensile test of the fil $m_strate composite. As the tensile deformation progressed, the cracks of the film were observed in the perpendicular direction to the tensile axis. Further deformation resulted in the plastic deformation with $45^{\circ}$ slip bands on the substrate surface. Spallation of the film occurred with the plastic deformation, which was initiated at the cracks of the film and was aligned along the slip directions. We found that both the cracking and the spallation behaviors are strongly dependent on the pre-treatment condition, such as Ar plasma pre-treatment. The spallation of the film was considerably suppressed in an optimized condition of the substrate cleaning by Ar glow discharge. We observed the improved stability with increasing duration of Ar plasma pre-treatment.nt.

• Computers and Concrete
• /
• v.3 no.4
• /
• pp.213-233
• /
• 2006

Over the past years techniques for non-linear analysis have been enhanced significantly via improved solution procedures, extended finite element techniques and increased robustness of constitutive models. Nevertheless, problems remain, especially for real world structures of softening materials like concrete. The softening gives negative stiffness and risk of bifurcations due to multiple cracks that compete to survive. Incremental-iterative techniques have difficulties in selecting and handling the local peaks and snap-backs. In this contribution, an alternative method is proposed. The softening diagram of negative slope is replaced by a saw-tooth diagram of positive slopes. The incremental-iterative Newton method is replaced by a series of linear analyses using a special scaling technique with subsequent stiffness/strength reduction per critical element. It is shown that this event-by-event strategy is robust and reliable. First, the model is shown to be objective with respect to mesh refinement. Next, the example of a large-scale dog-bone specimen in direct tension is analyzed using an isotropic version of the saw-tooth model. The model is capable of automatically providing the snap-back response. Subsequently, the saw-tooth model is extended to include anisotropy for fixed crack directions to accommodate both tensile cracking and compression strut action for reinforced concrete. Three different reinforced concrete structures are analyzed, a tension-pull specimen, a slender beam and a slab. In all cases, the model naturally provides the local peaks and snap-backs associated with the subsequent development of primary cracks starting from the rebar. The secant saw-tooth stiffness is always positive and the analysis always 'converges'. Bifurcations are prevented due to the scaling technique.

• Economic and Environmental Geology
• /
• v.54 no.3
• /
• pp.311-330
• /
• 2021

The Sinseongri site contains at least eleven theropod trackways, three sauropod trackways, and one or more ornithopod walkways of dinosaur footprints. The host rock at the site is primarily siltstone and mudstone, but thermal alterations have metamorphosed it into hornfels. Except for micro cracks and exfoliations, joint systems in various directions appeared on the surface of the fossils site and showed a low share of all damage factors. The host rocks in the fossils site demonstrated relatively high physical properties as a result of ultrasonic velocity and were classified as stable. More than half of the fossils required reinforcement to control the progression of cracks if the type of conservation treatment was subdivided according to the damage type of dinosaur footprint fossils. The white paint used to visualize the footprints seems to deteriorate, allowing rock debris to spill out and causing damage to the fossil site, and alternative visualization schemes should be considered.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.15-27
• /
• 2004

Sliding aspects of rock slope, where large-scaled tension cracks are induced during preliminary excavation, have been analyzed. Structure of rock mass is investigated by performing the electrical resistivity survey and the orientations and positions of discontinuities are measured from DOM-drilled core log. Geological evidence far primary failure movement has been detected and clay minerals which possess swelling properties are identified through XRD analysis. Slope stability is examined by considering the orientations of discontinuities and their trace distributions on the cut-face and neighboring natural slope surface. Both orientations and positions of failure-invoking discontinuity planes, traces of which are exposed within the anticipated sliding region, are concerned fur analyzing the preferred sliding directions. Regional sliding vectors are assessed based on the relative positions of potential sliding planes in the boreholes and the general trend of anticipated failure movement of rock slope is also investigated.