• 소성∙가공
• /
• 제4권3호
• /
• pp.233-244
• /
• 1995

Rolling force in the direct rolling(or twin-roll strip continuous casting) process fo semi-solid material has been computed using rigid-viscoplastic finite element method. Temperature distributions for calculations of rolling force and roll deformation are obtained from thermofluid analysis. Three dimensional roll deformation analysis has also been performed by using commercial package ANSYS. From the results, behavior of metal flow, rolling force and roll deformation have been investigated according to the process conditions of semi-solid direct rolling.

• 한국소음진동공학회논문집
• /
• 제17권1호
• /
• pp.17-23
• /
• 2007

In this paper, the modified direct method employing beam transformation technique is proposed in order to efficiently calculate hydroelastic responses of floating structure. Since the proposed method expresses the displacements of three-dimensional structure with those of transformed beam which leads to small number of equations of motion, the method is numerically efficient compared to the conventional direct method. To verify the efficiency of the proposed method, a 500 m-long floating structure under wave loads is considered in numerical example. Displacements, bending moments, torsion moments and shear forces are calculated and computing time is examined. The results are also compared with those of the conventional direct method.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1171-1178
• /
• 1992

본 연구에서는 직접접촉식 열교환기를 이용한 실험을 통하여 열교환기 설계에 가장 중요한 열교환기 단위 체적당 총괄 열전달 계수를 시스템의 작동조건에 따라 구 하여 실제 설계자료로 이용하는 데 그 목적이 있다.

• 유공압시스템학회논문집
• /
• 제1권4호
• /
• pp.1-8
• /
• 2004

The optimum design parameters of several hydraulic systems are obtained using the complex method that is one kind of constrained direct search method. First, the parameters of lead-lag controller of the direct drive servovalve is designed using the complex method to satisfy the steady-state error requirement. Second, the optimum locating point of hydraulic cylinder Is determined to minimize the cylinder force in the operation range of rotational sluice gate. For the third application case, the optimum piston area of hydraulic cylinder is determined to minimize the man power to elevate the manually operated sluice gate.

• 전기학회논문지P
• /
• 제54권2호
• /
• pp.67-72
• /
• 2005

This paper presents a method to select contingency ranking considering voltage security problems in power systems. Direct method which needs not the detailed knowledge of the post contingency voltage at each bus is used. Based on system operator's experience and knowledge, the membership functions for the MVAR mismatch and allowable voltage violation are justified describing linguistic representation with heuristic rules. Rule base is used for the computation of severity index for each contingency by fuzzy inference. Contingency ranking harmful to the system is formed by the index for security evaluation. Compared with 1P-1Q iteration, this algorithm using direct method and fuzzy inference shows higher computation speed and almost the same accuracy. The proposed method is applied to model system and KEPCO pratical system which consists of 311 buses and 609 lines to show its effectiveness.

• 한국자동차공학회논문집
• /
• 제2권3호
• /
• pp.75-84
• /
• 1994

In general direct-operated pressure reducing valves have been gardly applied to a dynamic control system such as active suspension control because of their poor control stability. But they are more robust than pilot-operated type and do not need pilot control flow. In this paper development of a new direct-operated proportional pressure reducing valve for low-band type active suspension control is reported. By means of a special damper directly linked to the valve spool, the control stability could be effectively improved without drawback in response time. The linearity error was less than $\pm$3.5%. Applied to an experimental active suspension system the new valve showed the $-90^{\circ}$ phase delay at 4Hz with 20% sinusoidal signal input and could control the suspension system with almost same performance as that with a pilot-operated type valve.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제8권3호
• /
• pp.1026-1039
• /
• 2014

We present a new method for generating sweep surfaces using bivariate B-spline motion. The sweep surface is defined as the trace of a single point under bivariate B-spline motion. Direct manipulation of the sweep surface is achieved by controlling its motion components while producing various editing effects. We demonstrate the effectiveness of our technique by modeling and deforming various three-dimensional shapes.

• 대한전기학회논문지
• /
• 제33권5호
• /
• pp.193-199
• /
• 1984

This paper presents a direct adaptive pole placement control scheme which is applicable to discretetime non-minimum phase systems. It is proved that by this scheme the poles can be placed at the desired locations and the overall state vector of the system is uniformly bounded if the reference input is sufficiently rich, and also proved that in case of insufficiently rich reference input the overall system can still be stabilized though the poles may not be placed exactly at the desired locations. The effectiveness of this scheme is verified by digital computer simulations.

• 대한전기학회논문지
• /
• 제40권6호
• /
• pp.606-614
• /
• 1991

A robust direct adaptive controller with respect to additive and multiplicative unmodeled dynamics is designed. A new term, proportional to the product of the bounded tracking error and normalizing signal, is added to the conventional control input for improvement of robustness and performances of an adaptive system. It is shown by the mathematical analysis and simulation results that the stability of the closed loop system is guaranteed and the performance of the system is improved.

• 대한기계학회논문집
• /
• 제13권6호
• /
• pp.1061-1069
• /
• 1989

본 연구에서는 제조공정을 생략하고, 보다 최종제품의 형상에 가까운 직접압 연법을 실현하기 위한 기초적 연구로서 두개의 회전하는 로울 내부를 냉각하면서 쐐기형 노즐을 통하여 폭이 균일한 용탕을 직접 주입하는 실험방법에 의해서 얻어진 주편의 표면상태와 주조조건과의 관계에 대하여 논하며 또한 기계적성질에 대하여 검토한다.