• 대한화학회지
• /
• 제14권4호
• /
• pp.327-332
• /
• 1970

A simple and convenient device for deflection-type direct reading the variations in electrolytic conductance is described and applied to the analysis of sulfur by combustion-$H_2O_2$ oxidation method. The apparatus consisted of a high resistance-ratio bridge in which the other adjacent arms are the differential cells. By adopting unusually high a-c voltage source for the bridge excitation, the a-c method for unbalanced bridge is established, decreased sensitivity owing to reduced bridge factor, 0.01, is overcome and also the absolute sensitivity and linearity are greatly improved. Over 50% variations in impedance of the balanced cell, within 1% deviation from the linearity can be attained with a volt (rms)order of output which was detected directly with VTVM without further amplification. Analysis of the bridge shows that these useful features are natural result of the constant current character of the high source impedance generator and the performance of the device agreed with the theoretical predictions. A standard procedure for the rapid analysis of sulfur using the bridge is also given, the analytical accuracy was approximately 1%. A determination takes not more than 5 minutes.

• 한국자동차공학회논문집
• /
• 제3권5호
• /
• pp.82-89
• /
• 1995

The three-dimensional fluid motion through the intake port and cylinder of a single DOHC SI engine was investigated with a commercial computational fluid dynamics simulation program, STAR-CD. This domain includes the intake port, intake valves and combustion chamber. Steady induction port flows for various valve lifts have been simulated for an actual engine configuration. The geometry was obtained by direct interface with a three-dimensional CAD software for complicated port and valve shape. The computational grid was generated using the commercial preprocessor ICEM CFD/CAE. Detailed procedures were presented on the generation of the geometry and the block-structured mesh. A standard k-${\varepsilon}$ turbulent model was applied to consider the complexity of the geometry and the fluid motion. The global flow patterns and the distributions of various quantities, such as pressure, velocity magnitude around the valve seat etc., were examined. The computational results, such as mass flow rate, discharge coefficient etc., for various valve lifts were compard with the experimental results and the computational results were found in good agreement with the experiment.

• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.9-18
• /
• 2000

Combustion and emission characteristics in a direct injection diesel engine is closely related to the intake port system. It is therefore important to understand the swirl flow characteristics formed by a helical intake port. However there are still many uncertainties. The purpose of this experimental study is to investigate the effects of the valve eccentricity ratio and the inlet flow conditions of a helical intake port on the characteristics of an in-cylinder swirl flow. A steady state flow test rig consisted of ISM(impulse swirl meter), LFM(laminar flow meter) and cylinder head with a helical intake port was used. The swirl ratio(Rs) and mean flow coefficient(Cf(mean)) with inlet flow conditions were measured. The results of these experiment can be summarized as follows. Swirl flow characteristics of a helical intake port are affected by the inlet flow conditions, and especially they are much affected by the length of a manifold runner and the rotational angle of a curved manifold runner.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 추계학술대회 논문집 학회본부
• /
• pp.172-174
• /
• 1994

Due to the environmental considerations and the energy crisis, there has been a revival of electric vehicles since 1960s. Research and development work concerning with electric vehicles (EVs) was becoming more intense in last decade. As compared with conventional internal combustion engine (ICE) cars, EVs have the advantages of clean, quiet, better energy efficiency, less maintenance and improving the load factor of electric power systems. However, EVs usually have a snort running range, bad acceleration performance and high initial cost. The main reason for these shortcomings is the low figure of energy density and the high per energy cost of battery at present technology state. So it is very important to optimize the overall drive system design with respect to the maximum utilization of battery, energy, motor torque and inverter power. This paper describes a demonstration model of electric car which is driven by 4-wheel direct method using the vector control.

• 공업화학
• /
• 제27권2호
• /
• pp.128-134
• /
• 2016

최근 셰일가스의 개발로 프로판, 부탄과 같은 경질알칸으로부터 프로필렌, 부텐, 부타디엔과 같은 올레핀을 제조하는 탈수소 공정에 대한 연구와 상용화가 많이 진행되었다. 특히 직접 탈수소화 반응의 열역학적 한계를 극복하고자 산화적 탈수소 또는 선택적 수소 산화 반응과 같이 산소를 활용한 기술의 연구개발이 진행되거나, 실제 공정에 적용된 사례들도 보고되고 있다. 이에 본 연구에서는 경질알칸의 탈수소 반응을 위한 산소활용기술의 최근 연구동향을 가스상의 산소를 활용하는 방법과 고체산화물의 격자산소를 활용한 기술로 나누어 정리하고, 산소활용기술의 현황과 연구 개발 방향 및 향후 전망에 대해 고찰하였다. 반응물의 반응성에 따라 기체상 산소의 적용이 용이한 경우와 반응성의 조절을 위해 격자산소를 이용하는 기술로 분류할 수 있었고, 전환율을 높이면서 선택도를 낮추지 않는 기술의 개발이 주요한 목표가 되었다.

• 해양환경안전학회지
• /
• 제25권3호
• /
• pp.381-394
• /
• 2019

The marine industry contributes a large proportion of the air pollutant emissions along coastal regions, and this air pollution has been strongly linked to cardiovascular diseases and other illnesses. To alleviate the problem, many ports have installed alternative maritime power (AMP) facilities that enable onboard marine auxiliary engines with generators (gensets) to be shut down while a ship is at berth. This study compared the emissions from conventional gensets with those from AMP facilities, focusing on four emission types: greenhouse gases (GHG), sulphur oxides (SOX), nitrogen oxides (NOX), and particulate matter (PM). Both direct (combustion / operation) and indirect (upstream) emissions were considered together for the emission comparison. The results showed that AMP has lower emissions than conventional onboard gensets, and this benefit is highly dependent on the electricity generation mix onshore. On average, GHG emissions could be reduced by about 18.3 %, while the other emissions (SOX, NOX, and PM) would decrease more dramatically (88.4 %, 90.1 %, and 91.5 %, respectively). Additionally, future benefits of the AMP would increase due to the expansion of renewable energies. Thus, this study supports the potential of AMP as a promising solution for environmental concerns at ports worldwide.

• 한국분무공학회지
• /
• 제28권4호
• /
• pp.176-183
• /
• 2023

Many countries are striving to reduce carbon emissions with the goal of net zero by 2050. Accordingly, vehicles are rapidly being electrified to reduce greenhouse gases in the transportation sector. However, many organizations predict that internal combustion engines of LDV (light-duty vehicle) will exist even in 2050, and it is difficult to electrify aircraft and large ships in a short time. Therefore, synthetic fuel (i.e., e-Fuel) that can reduce carbon emissions and replace existing fossil fuels is in the spotlight. The e-Fuel refers to a fuel synthesized by using carbon obtained through various carbon capture technologies and green hydrogen produced by eco-friendly renewable energy. The purpose of this study is to compare and analyze the injection and spray characteristics of the simulated e-Gasoline. We mixed the hydrocarbon fuel components according to the composition ratio of the synthetic fuel produced based on the FT(Fischer-Tropsch) process. As a result of injection rate measurement, simulated e-Gasoline showed no significant difference in injection delay and injection period compared to standard gasoline. However, due to the low vapor pressure of the simulated e-Gasoline, the spray tip penetration (STP) was lower, and the size of spray droplets was larger than that of traditional gasoline.

• 한국분무공학회지
• /
• 제28권4호
• /
• pp.191-197
• /
• 2023

LPG direct injection (LPDi) technology is a method of improving the weaknesses of existing LPG vehicles by directly injection into the combustion chamber. This study was conducted on the comparison of emissions and fuel efficiency performance of the engine and vehicle by applying LPDi technology. The LPDi hybrid engine's maximum output and maximum torque were measured at an equivalent level of less than 1% compared to conventional gasoline fuel. The fuel amount was corrected using the LCU controller, and the THC, CO, and NOx emissions were reduced to 90% in the operating range of the three-way catalyst through air-fuel ratio control. The analysis of THC+NOx and CO emissions in FTP-75 (CVS-75) driving mode satisfied the US LEV III SULEV30 regulation.

• 한국분무공학회지
• /
• 제28권4호
• /
• pp.169-175
• /
• 2023

Multi-injection scheme is being applied to GDI combustion to reduce PM and PN emission to meet the EU7 regulation. However, very short injection duration encounters the ballistic injection region, which injection quantity does not increase linearly with injection duration when applying multi-injection. In this study, numerical studies were conducted to reveal the cause of ballistic injection and the effect of design parameters on ballistic region using 1-D simulation, AMESim. Injection rate and injection quantity were compared with experiment to validate the established model, which showed the accuracy with 10% error. The model revealed that the tendency of ballistic region coincides with the needle motion behavior, which means that parameters at the upper part of needle such as electro-magnetic force, needle spring force and needle friction force have dominant effect on ballistic injection. To figure out the effect of electro-magnetic and needle friction force on ballistic, those parameters were varied to plus and minus 10% with model. The result showed that those parameters clearly changed the ballistic region characteristics, however, the impact became insignificant for outside of ballistic region, which means that the ballistic injection is mainly influenced by initial motion of injector needle.

• 해양환경안전학회지
• /
• 제21권2호
• /
• pp.188-193
• /
• 2015

일반적으로 선박용 디젤엔진의 아산화질소($N_2O$)배출률은 이산화황($SO_2$)배출률과 밀접한 상관성을 갖고 있고, 선박에서 사용되는 연료의 다양성은 $N_2O$배출특성에 영향을 미친다고 받아들여져 왔다. 최근의 연구보고에 의하면 연료 연소에서 발생한 충분한 일산화질소(NO)가 존재할 경우, 배기의 $SO_2$배출률이 $N_2O$생성에 미치는 영향은 NO의 영향보다 막대하게 크다. 그러므로 $SO_2$성분으로부터 기인하는 $N_2O$생성은 NOx저감을 위한 배기가스 재순환(EGR) 시스템에서 중요한 인자로 작용한다. 본 실험적인 연구의 목적은 $SO_2$유량 증가를 갖는 디젤엔진의 흡기가 배기의 $N_2O$배출률에 미치는 영향에 대하여 조사하는 것이다. 실험에 사용된 테스트 엔진은 2600rpm에서 12kW의 출력을 갖는 4행정 직접분사식 디젤엔진이고, 운전조건은 75% 부하에서 실시되었다. 0.499%($m^3/m^3$)의 $SO_2$표준가스는 흡기의 $SO_2$농도를 변화시키기 위해 사용되었다. 결과적으로 황 성분을 포함하지 않는 연료는 $SO_2$를 배출시키지 않았고, 흡기 중에 $SO_2$표준가스의 증가에 따른 배기의 $SO_2$배출률은 $SO_2$흡입률과 비교하여 거의 같은 비율이었다. 또한, 흡기의 $SO_2$유량 상승은 $N_2O$배출률을 상승시켜 배기 중의 $N_2O$는 흡기의 $SO_2$혼합기에 의해 생성되었다. 결국 황 성분을 함유한 연료는 연소 중에 $SO_2$를 형성하고 배기 중의 $N_2O$는 연소실에 존재하는 NO와 $SO_2$의 반응에 의해 발생된다고 할 수 있다.