• Korean Journal of Veterinary Service
• /
• v.41 no.2
• /
• pp.105-110
• /
• 2018

A total of 41 Salmonella (S.) strains were isolated from pigs suffered with severe watery diarrhea and were tried to identify by both matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) and polymerase chain reaction (PCR) analysis. Fibrinous exudate and ulceration in the large intestine were prevalent in gross observation, and variable degrees of enteritis were observed in the histology of large intestines. Subsequent polymerase chain reaction (PCR) analyses demonstrated that 41 strains were identified as S. Typhimurium (39 strains), though 2 stains were failed to identify. Further identification was performed using both direct smear and protein extraction method by MALDI-TOF MS analyses. In terms of extraction methods, 100% (41/41) of isolates were identified to species level of S. spp. Whereas only 43.9% (18/41) were identified to species level using the direct method. These results thus suggest that rapid and accurate diagnosis of porcine salmonellosis can be guaranteed by MALDI-TOF MS combined with protein extraction method.

• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.1078-1082
• /
• 1997

The distance in load parameter space to the closest voltage collapse point provides the worst case power margin and the left eigenvector identifies the most effective direction to steer the system to maximize voltage stability under contingency. This paper presents the results of the comparative performance study of the algorithms, which are applicable to a large scale power system, for computing the closest saddle node bifurcation (CSNB) point. Dobson's iterative method converges with robustness. However the slow process of updating the load increasing direction makes the algorithm less efficient. The direct method converges very quickly. But it diverges if the initial guess is not very close to CSNB. Zeng's method of estimating the approximate critical point in the pre-determined direction is attractive in the sense that it uses only using load flow equations. However, the method is found to be less efficient than Dobson's iterative method. It may be concluded from the above observation that the direct method with the initial values obtained by carrying out the iterative method twice is most efficient at this time and more efficient algorithms are needed for on-line application.

• Nuclear Engineering and Technology
• /
• v.47 no.3
• /
• pp.267-283
• /
• 2015

The main objective of this study is to investigate experimentally the two-phase flow characteristics in terms of the direct contact condensation of a steam-water stratified flow in a horizontal rectangular channel. Experiments were performed for both air-water and steam-water flows with a cocurrent flow configuration. This work presents the local temperature and velocity distributions in a water layer as well as the interfacial characteristics of both condensing and noncondensing fluid flows. The gas superficial velocity varied from 1.2 m/s to 2.0 m/s for air and from 1.2 m/s to 2.8 m/s for steam under a fixed inlet water superficial velocity of 0.025 m/s. Some advanced measurement methods have been applied to measure the local characteristics of the water layer thickness, temperature, and velocity fields in a horizontal stratified flow. The instantaneous velocity and temperature fields inside the water layer were measured using laser-induced fluorescence and particle image velocimetry, respectively. In addition, the water layer thickness was measured through an ultrasonic method.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.3
• /
• pp.175-181
• /
• 2020

For the success of a structural integrity management, it is essential to acquire structural response data at some critical locations with limited number of sensors. In this study, the structural response of numerical model was estimated by data fusion approach based on the Kalman filter known as stochastic recursive filter. Firstly, transient direct analysis was conducted to calculate the acceleration and strain of the numerical standing beam model, then the noise signals were mixed to generate the numerical measurement signals. The acceleration measurement signal was provided to the Kalman filter as an information on the external load, and the displacement measurement, which was transformed from the strain measurement by using strain-displacement conversion relationship, was provided into the Kalman filter as an observation information. Finally, the Kalman filter estimated the displacement by combining both displacements calculated from each numerically measured signal, then the estimated results were compared with the results of the transient direct analysis.

• Journal of Environmental Science International
• /
• v.5 no.1
• /
• pp.71-81
• /
• 1996

Direct Sky Blue-5B is an Azo dye known as general for staining of textile and leather, etc., and as materials which are difficult to be biodegraded in nature. The bacterium strain which could degrade direct Sky Blue-5B was isolated from activated sludge of dyeing factory and identified as Proteus sp. by experiment on morphological, cultural and biochemical characteristics, and so named Proteus sp. ST-1. The optimum condition of the strain for degradation of Sky Blue-5B were at about 35$^{\circ}C$ and PH 7~8. The strain had been capable of degradation with organic nitrogen effectively and had completely degraded 200mg/1 of the dye within 12hrs at 37$^{\circ}C$. The enzyme system related to degradation of Azo dye may be intracellular, and so degraded the dye after absorption into cell. The degradation products of Sky Blue-5B by Proton sp. 57-1 were analyzed by Gas Chromatography /Mass Spectrometry and Spectrophotomer, from this observation, it may be infered that the strain degraded the dye directly without any mediate.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.4
• /
• pp.81-89
• /
• 1998

In the field of industrial drives, the vector control of the induction motor has been widely used to achieve the good control performance. In this paper, to require the information of rotor flux in direct vector control scheme, the flux observer by current model of rotor circuit is used. This flux observer is not only available at low-speed region bt good for the error reduction by feedback properties. Also, employing the flux observer on rotor reference frame, the robustness of decoupling control to the observation of rotor flux can be achieved. Through digital simulation and DSP-based IGBT inverter system, the validity for practical implementation is verified.

• Smart Structures and Systems
• /
• v.30 no.3
• /
• pp.273-286
• /
• 2022

In recent years, vision-based monitoring has received great attention. However, structural identification using vision-based displacement measurements is far less established. Especially, simultaneous identification of structural systems and unknown excitation using vision-based displacement measurements is still a challenging task since the unknown excitations do not appear directly in the observation equations. Moreover, measurement accuracy deteriorates over a wider field of view by vision-based monitoring, so, only a portion of the structure is measured instead of targeting a whole structure when using monocular vision. In this paper, the identification of structural system and excitations using vision-based displacement measurements is investigated. It is based on substructure identification approach to treat of problem of limited field of view of vision-based monitoring. For the identification of a target substructure, substructure interaction forces are treated as unknown inputs. A smoothing extended Kalman filter with unknown inputs without direct feedthrough is proposed for the simultaneous identification of substructure and unknown inputs using vision-based displacement measurements. The smoothing makes the identification robust to measurement noises. The proposed algorithm is first validated by the identification of a three-span continuous beam bridge under an impact load. Then, it is investigated by the more difficult identification of a frame and unknown wind excitation. Both examples validate the good performances of the proposed method.

• Transactions of Materials Processing
• /
• v.29 no.2
• /
• pp.103-112
• /
• 2020

This study explores the effects of different pre-machining conditions on the deposition characteristics and mechanical properties of austenitic stainless steel samples repaired using direct energy deposition (DED). In the DED repair process, defects such as pores and cracks can occur at the interface between the substrate and deposited material. In this study, we varied the shape of the pre-machined zone for repair in order to prevent cracks from occurring at the slope surface. After repairs by the DED process, macro-scale cracks were observed in samples that had been pre-machined with elliptic and trapezoidal grooves. In addition, it was not possible to completely prevent micro-crack generation on the sloped interfaces, even in the capsule-type grooved sample. From observation of the fracture surfaces, it was found that the cracks around the inclined interface were due to a lack of fusion between the substrate and the powder material, which led to low tensile properties. The specimen with the capsule-type groove provided the highest tensile strength and elongation (respective of 46% and 571% compared to the trapezoidal grooved specimen). However, the tensile properties were degraded compared to the non-repaired specimen (as-hot rolled material). The fracture characteristics of the repaired specimens were determined by the cracks at the sloped interfaces. These cracks grew and coalesced with each other to form macro-cracks, they then coalesced with other cracks and propagated to the substrate, causing final fracture.

• Journal of Environmental Health Sciences
• /
• v.39 no.6
• /
• pp.532-540
• /
• 2013

Background: Exposure factors for consumer products have been developed since the 1980s. Such exposure factors are important in risk assessment. Since the exposure/use patterns of consumer products in a country may reflect its respective cultural, meteorological, and socio-economic circumstances, unique Korean exposure factors for consumer products are needed. Such exposure factors are required for newly-enacted chemical regulations in Korea. For this review, published papers and survey reports on exposure factors of consumer products were examined for their assessment methodologies. Results: Investigation into exposure factors for consumer products used a variety of methods: home visit, online, telephone, and mail surveys using questionnaires; face to face interviews; modeling using a constructed database; and direct measurement. To collect more accurate exposure information or to check the reliability of the sampling method, some studies were repeated using the same questionnaire, in-home observation, direct measurement of usage, and videotaping. In Korea, nationwide exposure surveys were conducted five times over five years to obtain Korean exposure factors. However, with the exception of the $5^{th}$-year study, the surveys were online questionnaires and only the $5^{th}$-year study validated the accuracy of exposure information by re-visits and direct measurement. Conclusion: Accurate exposure factors are an essential part of risk assessment to assure safe use of consumer products. For better and safer management of consumer products, accurate exposure factors in Korea should be assessed for various exposure pathways.

• The Journal of the Korean dental association
• /
• v.56 no.9
• /
• pp.462-478
• /
• 2018

The presence of implant-prosthesis misfits can cause various complications. It is very important to detect misfits to prevent such complications. There are various evaluation methods for misfit assessment including clinical methods and laboratory in vitro methods. The clinical misfit evaluation includes radiographic analysis, visual observation, probing, Sheffield test, evaluation with disclosing materials, and screw resistance test. The laboratory in vitro evaluation method includes indirect modelling evaluation and direct metrological visualization. Of the indirect modelling methods, photoelastic stress analysis, finite element analysis, strain gauge analysis, and microbial colonization analysis were reviewed. Of the direct metrological visualization, microscopic analysis, 3-D photogrammetric analysis, coordinate measuring analysis, and radiographic analysis were reviewed. In this review, the characteristics, advantages and disadvantages of each method were evaluated.