• The Journal of Internal Korean Medicine
• /
• v.23 no.1
• /
• pp.25-31
• /
• 2002

Objectives : To prevent stroke, it is very important to reduce risk factors which might cause stroke. However, previous studies that having investigated coffee consumption associated with stroke reported various results. In addition, there were only a few studies based on the Korean population. Therefore, we studied the association of coffee consumption and the possibility of getting stroke among Koreans. Methods : A case-control study was carried out on 207 cases(stroke patients) and 207 controls(non-stroke patients) in a hospital. Information on characteristics, health habits, dietary habits and coffee consumption were obtained through direct interview by using an organized questionnaire; WHR(Waist-Hip Ratio) was determined through physical examination. The coffee consumption was classified by the average frequency of intake, such as less than 1 cup/day, 2-3 cups/day, more than 5 cups/day). Possible confounding effects of age, sex, smoking and alcohol drinking were controlled by multiple logistically regressive analysis. Results : After adjusting age and sex, coffee consumption significantly increased risk factors of stroke(${\leq}$1 cup/day OR=1.018, 95% CI=0.631-1.644; 2-3 cup/day OR=1.782, 95%CI=1.032-3.079;${\geq}$5 cup/day OR=1.210, 95% CI=0.588-2.490). When other factors were controlled, the risk factors of stroke were associated with alcohol drinking, whereas no significant association was observed with coffee consumption. Conclusion : Coffee consumption is not a major risk factor of causing stroke in this study. Prospective and cohort study on the association between coffee consumption and the possibility of getting strokes among the Korean population will be needed in the future.

• Journal of Powder Materials
• /
• v.25 no.2
• /
• pp.120-125
• /
• 2018

Boron nitride nanotubes (BNNTs) are receiving great attention because of their unusual material properties, such as high thermal conductivity, mechanical strength, and electrical resistance. However, high-throughput and high-efficiency synthesis of BNNTs has been hindered due to the high boiling point of boron (${\sim}4000^{\circ}C$) and weak interaction between boron and nitrogen. Although, hydrogen-catalyzed plasma synthesis has shown potential for scalable synthesis of BNNTs, the direct use of $H_2$ gas as a precursor material is not strongly recommended, as it is extremely flammable. In the present study, BNNTs have been synthesized using radio-frequency inductively coupled thermal plasma (RF-ITP) catalyzed by solid-state ammonium chloride ($NH_4Cl$), a safe catalyst materials for BNNT synthesis. Similar to BNNTs synthesized from h-BN (hexagonal boron nitride) + $H_2$, successful fabrication of BNNTs synthesized from $h-BN+NH_4Cl$ is confirmed by their sheet-like properties, FE-SEM images, and XRD analysis. In addition, improved dispersion properties in aqueous solution are found in BNNTs synthesized from $h-BN+NH_4Cl$.

• Journal of Korean society of Dental Hygiene
• /
• v.7 no.3
• /
• pp.273-284
• /
• 2007

Oral health in youth is very important because this period influences life for adult remarkably. Therefore, more effective oral health education and recognition of early treatment for oral disease are required sincerely. For more effectual education for high-school students, it is necessary to consider their circumstance like obesity and smoking. This study will analyze the correlation oral health behavior with obesity and subjective oral health concerns. In addition to, the actual condition of smoking for high-school girls and oral health condition will be verified. A survey was progressed for high-school girls in Busan city and BMI(body mass index) was used for classification of weight. The statistical significance was analyzed using SPSS 13.3 for Windows. Results of this study is following. 1. The frequence of daily toothbrushing was significantly different with obesity although difference of oral health knowledge was not significant. The frequency of toothbrushing of overweight students were lesser than the others. This results may be caused by low-level for oral health concerns and by passive life style of fat person. This habit has possibility of causing serious periodontal disease like periodontitis and tooth caries. 2. The correlation of obesity and time of brush change, using for supplement, and recent dental institution was insignificant. However, concerns of oral health were showed significantly according to obesity. Under-weight and standard-weight students were more concerned about oral health than over-weight. This results can be related to frequence of toothbrushing for fat subject. This relevance of two factors was confirmed by logistic regression analysis. 3. Approximately 70% students have smoking experience responded to uncomfortableness of periodontal conditions. On the other hand, non-smoking students felt uncomfortable in 50%. This results indicated that smoking have an effect on oral health condition. Further study which identify periodontal conditions practically has to go on for verification of direct correlation smoking and oral health.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.12
• /
• pp.13-22
• /
• 2015

Developed ground cavity due to leakage of decrepit old sewer pipe causes ground surface settlement and brittle fracture of pavement. Recently, for 5 years, frequency of occurrence of ground subsidence phenomenon tends to increase rapidly and/or steadily. It is difficult to investigate ground surface settlement and/or subsidence in urban area because most ground surfaces are covered with asphalt or concrete pavement. In this research, therefore, ground surface settlement, influence zone and settlement of sewer pipe were analyzed using finite element method. Not only reinforced effect of pseudo-plastic backfill that is applied to prevent ground surface settlement or subsidence spot, was compared and analyzed using numerical analysis program, but also direct shear test was carried out to determine strength parameters of pseudo-plastic backfill.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.3
• /
• pp.314-324
• /
• 2006

Statement of problem. Osseointegration is important mechanism of dental implant but it is not easy to evaluate. Indirect measurement is non-invasive and clinically applicable but they need more study about correlation between indirect values and degree of osseointegration. Purpose. The aims of this study were to evaluate the coefficient of correlation between indirect measurement and direct measurement under different healing time, and assessment of effect of initial insertion torque to the implant stability. Material and Methods. 20 rabbits received 3 implants on each side of tibia. Three kinds of implants (machined surface implant, Sandblasted with Large grit and Acid etched implant, Resorbable Blast Media treated implant) were used. During the surgery implant insertion torque were measured with $Osseocare^{TM}$. After the 1, 4, 8, 12 weeks of healing time, animals were sacrificed and stability values (Implant Stability Quotient with $Osstell^{TM}$, removal torque with torque gauge) were measured. Results. The Bone quality of rabbit tibia was classified into 2 groups according to the insertion torque. Resonance frequency analysis (ISQ) and removal torque showed positive correlation until $4^{th}$ week (r=0.555, p=0.040). After $8^{th}$ week (r=0.011, p=0.970) the correlation became weak and it turned negative at $12^{th}$ week (r=-0.074, p=0.801). Insertion torque and ISQ showed changing correlation upon the healing time ($1^{st}$ week: r=0.301, p=0.033, $4^{th}$ week: r=-0.429, p=0.018, $8^{th}$ week: r=0.032, p=0.865, $12^{th}$ week: r=-0.398, p=0.029). Insertion torque and removal torque has positive correlation but it was not statistically significant ($1^{st}$ week: r=0.410, p=0.129, $4^{th}$ week: r=0.156, p=0.578, $8^{th}$ week: r=0.236, p=0.398, $12^{th}$ week: r=0.260, p=0.350). Conclusion. In this study, bone quality may affect the degree of osseointegration positively during healing time and correlation between ISQ and degree of osseointegration can be different according to the healing time and bone quality.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.1
• /
• pp.139-149
• /
• 2006

This study is to analyze the kinematic variables of inward $1{\frac{1}{2}}$ somersault in platform diver. For the manner, 3 people form the national diving team in the year 2000were chosen as the subjects and two S-VHS video cameras set in 60frames/sec were used for recording their motions. Coordinated raw positions data through digitizing are smoothing by butter-worth's low-pass filterin method at a cut off frequency 6.0Hz. and the direct linear transformation(DLT) method was employed to obtain 3-D position coordinates. The conclusions were as follows. However, horizontal distance which is the change of the COG, form the point of the jump to the point of Event 3 where the player is out of the board range completely, Subject B showed 105.1cm and 71.1cm of the vertical distance which are shorter horizontal distance and higher vertical distance, thus, took a great advantage of the position to prepare for the entry. Therefore, if a player takes higher position by speeding up the vertical velocity at the moment of the jumping off the board, and stays in the air longer, the player can have more time to show his skill. Because of the use of the characteristics of the inward somersault, keeping the safe distance form the board is important but in order to higher the completeness, it is ideal to keep the horizontal distance little over 100cm. Also, the angles of shoulder and elbow from Event 1 to 4, depending on swing of the arms, motions in the air, getting ready for the entry, showed some difference individual by individual, according to the velocity of the thigh and shank showed much difference while getting ready and take-off, and it's because of the individual's different bending and straightening for horizontal and vertical distance.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.1
• /
• pp.13-26
• /
• 2004

The purpose of this study was to investigate the differences of the kinematical and the kinetical factors that calculated from preflight to preflight of salto forward straight 3/2 turn motion between skillers and less-skillers. four S-VHS video cameras operating at 60Hz were used to record the performances. Five elite male gymnasts were participated in this study as subjects. Three-dimensional coordinates of 21 body landmarks during each trial were collected using a Direct Linear Transformation method. The raw 3-D coordinates of the 21 body landmarks were smoothed using a second order lowpass, recursive Butterworth digital filter and a cutoff frequency of 10Hz. Load cells attached on the beneath of a board were used to attain the kinetic variables. It was found that the more angular momentum in the longitudinal axis, the less vertical velocity and these angular momentum effected the height of peak in the preflight. Also, it was revealed that the larger angular momentum in the medio-lateral axis was rather than it in the longitudinal axis to increase vertical height and rotation force of the body. For the reaction force of springboard, the vertical and the horizontal reaction force were 16.52BW and 3.45BW, respectively. It was found that the higher value of the vertical reaction force induced the faster vertical velocity and the higher an ar momentum. of the whole body center of gravity.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.17 no.2
• /
• pp.11-16
• /
• 1980

For vibration analysis of stiffened plates the orthotropic plate analogy is commonly accepted. As to stiffened plates in contact with water, however, there is still much uncertainty in estimation of the added mass because of the lack of direct methods. The authors, considering that for added mass of plates there are many reliable data derived theoretically or experimentally available, suggest a method to estimate the added mass of a stiffened plate by combining the mass increase factor, $\beta$, of an equivalent orthotropic plate and the correction factor, $\kappa$, for the effects of stiffeners. The latter is to be derived from systematic experimental investigations. Then, the natural frequency in water, f', can be calculated from that in air, f, by the equation $f'=f/\sqrt{1+\kappa\beta}$. To investigate practical applicability of this method, a systematic experiment was carried out with five uniaxially stiffened plates. Each of them had a plate of same size, $600mm{\times}600mm{\times}3.2mm$, but stiffeners of different size in the web-depth, 41.6mm, 51.2mm or 66.8mm and of different spacing 75mm, 100mm, or 150mm. Natural frequencies were measured under simply supported-edge conditions in both air and water, and corresponding $\kappa$ values derived. In spite of wide variations of web-depth and spcae of stiffeners, the experimental results show that the diversity of $\kappa$ values is not remarkable; mean values of $\kappa$ are 1.31 with standard deviation of 0.025 for the first modes and 1.27 with that 0.077 for the second modes. Hence, the authors concluded that the above $\kappa$ values can be used generally for the cases of uniaxially stiffened plates both sides of which contact with water, and that $\kappa$ values of general use for the cases of cross-stiffened plates may also be obtainable from similar experiments.

• Journal of Communications and Networks
• /
• v.17 no.6
• /
• pp.622-633
• /
• 2015

The coexistence among different systems is a major problem in communications. Mutual interference between different systems should be analyzed and mitigated before their deployment. The paper focuses on two aspects that have an impact on the system performance. First, the coexistence analysis, i.e. evaluating the mutual interference. Second aspect is the coexistence techniques, i.e. appropriate system modifications that guarantee the simultaneous use of the spectrum by different technologies. In particular, the coexistence problem is analyzed between ultra-wide bandwidth (UWB) and narrow bandwidth (NB) systems emphasizing the role of spectrum sensing to identify and classify the NB interferers that mostly affect the performance of UWB system. A direct sequence (DS)-time hopping (TH) code design technique is used to mitigate the identified NB interference. Due to the severe effect of Narrowband Interference on UWB communications, we propose an UWB transceiver that utilizes spectrum-sensing techniques together with mitigation techniques. The proposed transceiver improves both the UWB and NB systems performance by adaptively reducing the mutual interference. Detection and avoidance method is used where spectrum is sensed every time duration to detect the NB interferer's frequency location and power avoiding it's effect by using the appropriate mitigation technique. Two scenarios are presented to identify, classify, and mitigate NB interferers.

• Wind and Structures
• /
• v.14 no.4
• /
• pp.301-319
• /
• 2011

The full-scale measurements are compared with the wind tunnel test results for the long-span roof latticed spatial structure of Shenzhen Citizen Center. A direct comparison of model testing results to full-scale measurements is always desirable, not only in validating the experimental data and methods but also in providing better understanding of the physics such as Reynolds numbers and scale effects. Since the quantity and location of full-scale measurements points are different from those of the wind tunnel tests taps, the weighted proper orthogonal decomposition technique is applied to the wind pressure data obtained from the wind tunnel tests to generate a time history of wind load vector, then loads acted on all the internal nodes are obtained by interpolation technique. The nodal mean wind pressure coefficients, root-mean-square of wind pressure coefficients and wind pressure power spectrum are also calculated. The time and frequency domain characteristics of full-scale measurements wind load are analyzed based on filtered data-acquisitions. In the analysis, special attention is paid to the distributions of the mean wind pressure coefficients of center part of Shenzhen Citizen Center long-span roof spatial latticed structure. Furthermore, a brief discussion about difference between the wind pressure power spectrum from the wind tunnel experiments and that from the full-scale in-site measurements is compared. The result is important fundament of wind-induced dynamic response of long-span spatial latticed structures.