• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1156-1165
• /
• 2018

This paper presents a detailed realization of direct torque controlled induction motor drive for elevator applications. The drive is controlled according to the well-known space vector modulated direct control scheme (SVM-DTC). As the elevator drives are usually equipped with speed sensors, flux estimation is carried out using a current model where two stator currents are measured and accurate instantaneous rotor speed measurement is used to overcome the need for measuring stator voltages. Speed profiling for a comfortable elevator ride and other supervisory control activities to provide smooth operation are also explained. The drive performance is examined and controllers' parameters are fine-tuned using MATLAB/SIMULINK. The blocks used for flux and torque estimation and control in the offline simulation are compiled for real-time using dSPACE Microlabox. The performance of the drive has been verified experimentally. The results show good performance under transient and steady state conditions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.825-833
• /
• 2016

This paper introduces a direct-conversion CMOS RF transmitter for the IEEE 802.15.4 standard with a low-power high-gain up-conversion mixer designed in $0.18{\mu}m$ process. The designed RF DCT(Direct Conversion Transmitter) is composed of differential DAC(Digital to Analog Converter), passive low-pass filter, quadrature active mixer and drive amplifier. The most important characteristic in designing RF DCT is to satisfy the 2.4 GHz Zigbee standard in low power. The quadrature active mixer inside the proposed RF DCT provides enough high gain as well as sufficient linearity using a gain boosting technique. The measurement results for the proposed transmitter show very low power consumption of 7.8 mA, output power more than 0 dBm and ACPR (Adjacent Channel Power Ratio) of -30 dBc.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2006.07a
• /
• pp.689-689
• /
• 2006

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.154-157
• /
• 2000

One of the problems using DCR(Direct Conversion Receiver) type architecture are DC offset, Poor channel selectivity. APDP(Anti Parallel Diode Pair) can be mood candidate for the DCR frequency mixer due to its inherent 2nd harmonic suppression. APDP shows good IP2 and DC suppression. This paper describes single APDP LO power characteristics, IP2, and receiver structure utilizing APDP frequency mixer.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1367-1374
• /
• 2016

This paper presents a discrete-time version of voltage and current limited operation using an enhanced direct torque and flux control method for interior permanent magnet synchronous motor (IPMSM) drives. A command voltage vector for airgap torque and stator flux regulation can be uniquely determined by the finite-settling-step direct torque and flux control (FSS-DTFC) algorithm under physical constraints. The proposed command voltage vector trajectories can be developed to achieve the maximum inverter voltage utilization for the discrete-time current limit (DTCL)-based FSS-DTFC. The algorithm can produce adequate results over a number of the potential secondary upsets found in the steady-state current limit (SSCL)-based DTFC. The fast changes in the torque and stator flux linkage improve the dynamic responses significantly over a wide constant-power operating region. The control strategy was evaluated on a 900W IPMSM in both simulations and experiments.

• Wind and Structures
• /
• v.22 no.6
• /
• pp.635-662
• /
• 2016

This paper deals with the comparison of different control strategies for the Induction generators in wind energy conversion system. Mainly, two types of induction machines, Self excited induction generator (SEIG) and doubly Fed Induction generators (DFIG) are studied. The different control strategies for SEIG and DFIG are compared. For SEIG, Electronic load Controller mechanism, Static Compensator based voltage regulator are studied. For DFIG the main control strategy namely vector control, direct torque control and direct power control are implemented. Apart from these control strategies for both SEIG and DFIG to improve the performance, the ANFIS based controller is introduced in both STATCOM and DTC methods. These control methods are simulated using MATLAB/SIMULINK and performances are analyzed and compared.

• Journal of information and communication convergence engineering
• /
• v.6 no.4
• /
• pp.439-443
• /
• 2008

It is shown that even if the modulating frequency of the light is too high for direct detection the signal can be extracted by frequency conversion at the same time as the detection by means of the nonlinearity of the APD. When this frequency conversion detection is applied to an optical receiver, the detection bandwidth can be increased while the configuration of the optical detection circuit and the signal processing in the subsequent stages are simplified. A fundamental analysis is carried out with an APD which is confirmed experimentally.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.6
• /
• pp.1151-1156
• /
• 2007

In this paper, we develop a new conversion method for implementing binary ECG(Electrocardiogram) conversion scheme to improve our previous research works that supported the conversion of binary ECG files into HL7 aECG for enhancing interoperability of ECG data. HL7 aECG is a XML-based standard for interoperability of ECG waveform. To improve the performance of ECG data conversion, we utilize a compilation-based ECG conversion method on binary ECG files. Our new method supports both flexibility of BED-based ECG conversion mechanism and the performance of direct conversion mechanism.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.329-339
• /
• 2006

The production of lower olefins from methanol becomes an attractive process because of the rapid increase in crude oil price. This paper reivews the conversion mechanisms of methanol to hydrocarbons over zeolite and SAPO molecular sieve catalysts to understand the formation steps of lower olefins from methanol. The feasibility of the conversion mechanisms such as the direct mechanism based on well-defined intermediates and the hydrocarbon pool mechanism involving hydrocarbon moieties as an active centers is discussed with reepect to the induction period, the selectivity for products and the deactivation phenomena of the methanol conversion. The literature appeered since 1999 for the structure of the hydrocarbon pool and its catalytic role in the methanol conversion are summariged, and the prospect for the methanol-to-olefins process is described.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.18-26
• /
• 2015

In this paper, we studied the method for analyzing and estimating the parameters that induce I/Q imbalance in the repeater using direct conversion RF. In repeater, amplitude, phase, and filter mismatch are generated in the receiving-end which converts RF signal to baseband signal. And amplitude and phase mismatch are generated in the transmitting-end which converts baseband signal to RF signal. Accordingly, we modeled the parameters that cause I/Q imbalance in the structure of the repeater in order, and proposed a feedback test structure from the transmitting-end to the receiving-end for estimating the corresponding parameters. By comparing the test transmitting signal and received signal, it is possible to estimate the I/Q imbalance parameters which occurred from mixed components of real and imaginary part. And it was confirmed that I/Q imbalance phenomenon has been properly compensated with estimated parameters at the direct conversion RF repeater.