• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.774-780
• /
• 1997

Porous low reflective coating films of SiO2.ZrO2 system were prepared from the mixed alkoxide solutions of Zr(O-nC3H7)4 and partially prehydrolyzed TEOS by the sol-gel method using the dip-coating technique. In the case of 90SiO2.10ZrO2 porous coating films with HCl and H2O content was 0.3 mole and 4 mole, 378 m2/g of the specific surface area, 0.254 cm3/g of total pore volume, 30-50$\AA$ of average pore diameter. The transmittance of 90SiO2.10ZrO2 porous coated films was 95.38% at the wavelength of 550 nm, compared with the parent glass, the transmittance was increased with 4.38%.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.244-245
• /
• 2009

Sol-gel coatings of $TiO_2$ have been prepared from $TiO_2$ sol and deposited by dip-coating technique on 316L stainless steel sheets in order to study the electrochemical behaviorin corrosive solutions. The influence of the coatings on the chemical corrosion of the substrate has been evaluated by potentiodynamic polarization curves in different aqueous NaCl solution at $25^{\circ}C$.

• 전기화학회지
• /
• 제9권2호
• /
• pp.59-63
• /
• 2006

전해코팅 법과 dip-coating 법을 이용해 산화주석(IV)을 티타늄 지지체에 코팅하여, 코팅 방법에 따른 코팅 전극의 물성과 전기화학적 특성에 대해여 연구하였다. HCl 로 전극 에칭 후, nitrate 용액에 $SnCl_2{\cdot}2H_2O$을 용해시켜 pulse technique를 이용하여 전해코팅 하였으며, dip-coating 법 또한 $SnCl_2{\cdot}2H_2O$를 사용하여 1:1V% HCl 용액에 용해시켜 코팅 소결 후 산화주석(IV)코팅 전극을 제작하였다. 두 가지 코팅 방법을 통해 제작된 산화주석(IV)코팅 전극은 전극의 물성을 비교하기 위해 x-ray diffraction (XRD), scanning election microscopy (SEM)를 관찰해보았고, 전기화학적 특성을 평가하기 위해 cyclic voltammetry (CV)를 측정하여 전위창을 비교해 보았다.

• 한국세라믹학회지
• /
• 제29권12호
• /
• pp.970-980
• /
• 1992

${\gamma}-alumina$ membranes were prepared by sol-gel dip coating or pressurized coating of boehmite sols on slipcasted ${\gamma}-alumina$ support tubes. The particle size of sols synthesized via the modified Yoldas-method could be controlled below 5 mn according to the mole ratio of nitric acid/aluminumtri-sec-butoxide (0.07~1.0). The reproducible crack-free composite membranes were produced by the 2nd dip coating or the pressurized coating technique using very stable sols with the particle size of 45 nm. Nitrogen gas permeability through the top-layer in the composite membrane was about $70~55{\times}10^{-7}\;mol/m^2{\cdot}s{\cdot}Pa$. The thermal stability of the top layer was proved to be good enough upto the heat-treatment temperature of $500^{\circ}C$.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.747-757
• /
• 1997

ZSM-5 zeolite composite membranes have been synthesized from a silica sol solution containing TPABr as an organic template by the dip-coating and the pressurized-coating hydrothermal treatment techniques. The CO2 separation efficiency of synthesized composite membranes was also investigated. The permeation mechanism of CO2 through ZSM-5 membranses was the surface diffusion, and that of N2, O2, and He gases was Knudsen diffusion or activated diffusion depending on the synthetic method of membranes and the measurement temperature. The CO2/N2 separation factor of the membrane prepared by the dip-coating hydrothermal treatment was 2.5 at about 12$0^{\circ}C$, while the ZSM-5 composite membrane synthesized by the pressurized-coating hydrothermal treatment technique showed the CO2/N2 separation factor of 9.0 at room temperature higher than that ever reported in the literature.

• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.249-252
• /
• 1997

Highly oriented ZnO thin films were fabricated by dip-coating technique using zinc acetate 2-methoxyethanol 2-aminoethanol solution as starting materials, and effects of substrates on the film's orientation were investigated. Product films were obtained by prefiring at 300, 400, 500 and 550℃ for 10 min, followed by final heat-treatment at the same temperatures as prefiring for 1h. c-axis oriented films on glass substrates were prepared by heat treatment of prefiring films at 300-550℃, while films on alumina showed polycrystalline structure. Films with c-axis orientation exhibited lower specific resistivities than those of polycrystalline films with partial crack and pore.

• Corrosion Science and Technology
• /
• 제9권5호
• /
• pp.175-186
• /
• 2010

The auto industry is demanding more ductile high-strength steel grades to build lighter and stronger car bodies. The hot-dip galvanizing problems of these new steel grades are creating a demand for an improved method to control zinc wettability. The simplest way to improve zinc wettability on industrial hot-dip galvanizing lines is to increase the strip immersion temperature at zinc bath entry for enhancing the aluminothermic reaction. However, this practice increases the reactivity due to overheating the zinc in the snout which induces the formation of brittle Fe-Zn compounds at the strip/coating interface with the formation of higher amounts of dross in the zinc bath and snout contamination. Thus, this simple practice can only be utilized for short production periods of one to two hours without deteriorating coating quality. This problem has been solved by employing a technique that allows the use of a higher and attuned strip immersion temperature at zinc bath entry while still maintaining a constantly low zinc bath temperature. This has been proven to provide the solution for both the improved wettability and a significant reduction in the amounts of dross in the zinc bath.

• Tribology and Lubricants
• /
• 제37권2호
• /
• pp.71-76
• /
• 2021

As opposed to using fossil fuels, we need to use eco-friendly resources such as sunlight, raindrops and wind to produce electricity and combat environmental pollution. A triboelectric nanogenerator (TENG) is a device that converts mechanical energy into electricity by inducing repetitive contact and separation of two dissimilar materials. During the contact and separation processes, electron flow occurs owing to a change in electric potential of the contacting surface caused by contact electrification and electrostatic induction mechanisms. A solid-solid contact TENG is widely known, but it is possible to generate electricity via liquid-solid contact. Therefore, by designing a hydrophobic TENG, we can gather electricity from raindrop energy in a feasible manner. To fabricate the superhydrophobic surface of TENGs, we employ a dip coating technique to synthesize an octadecylamine (ODA)- and polydimethylsiloxane (PDMS)-based coating on polyethylene terephthalate (PET). The synthesized coating exhibits superhydrophobicity with a contact angle greater than 150° and generates a current of 2.2 ㎂/L while water droplets fall onto it continuously. Hence, we prepare a box-type TENG, with the ODA/PDMS coating deposited on the inside, and place a 1.5 mL water droplet into it. Resultantly, we confirm that the induced vibration causes continuous impacts between the ODA/PDMS coating and the water, generating approximately 100 pA for each impact.

• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.49-57
• /
• 2004

습도센서의 감습막으로 응용하기 위하여 폴리이온넨계 전해질 잉크를 제조하였다. 감습필름 은 금전극이 인쇄된 알루미나 기판 위에 잉크젯 인쇄 기법을 사용하여 도포 하였다. 또한 methyl methacrylate, acrylic acid, 2-hydroxyethyl methacrylate 그리고 [(2-methacryloyloxy)ethyl)ethyl]trimethylammonium chloride의 공중합체를 합성하였으며, 이것은 침적코팅에 의한 감습막 제조에 사용하였다. 상대습도에 따른 전기적 특성을 측정하였으며 침적코팅에 의한 습도센서와 비교하였다. 습도센서는 상대습도가 증가함에 따라서 저항의 감소함을 보여주었으며 그들의 저항특성은 시료간에 가깝게 일치함을 보여주었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1386-1388
• /
• 2009

We report on a new method of fabricating color filters based on selective wetting of color inks. The reversible formation of a hydrophobic layer provides sequential generation and protection of successive color filter patterns through a simple coating process. The transmittance and geometrical properties of the fabricated color filter were described.